Design and experimental study of a two-dimensional position sensitive X-ray detector

A prototype of a two-dimensional position sensitive X-ray detector was designed and constructed for small angle X-ray scattering experiments at BSFR (Beijing Synchrotron Radiation Facility). The detector is based on MWPC with cathode strip readout, and has a sensitive area of 200 mm×200 mm. The spatial resolution (FWHM) of about 210 μm along the anode wire direction was obtained from the ⁵⁵Fe X-ray test of the detector.     

Study of a position-sensitive scintillator neutron detector

The investigation of a novel thermal neutron detector is developed to fulfill the requirements of the high intensity power diffractometer (HIPD) at the Chinese Spallation Neutron Source (CSNS). It consists of two layers of ⁶LiF/ZnS(Ag) scintillators, two layers of crossed WLSF arrays, several multi-anode photo multiplier tubes (MA-PMT), and the matching readout electronics. The neutron detection efficiency of the scintilltors, the light transportation ability of the WLSF, and the spatial linearity of the readout electronics are measured and discussed in this paper. It shows that the sandwich structure and the compact readout electronics could fulfill the needs of the HIPD. A prototype with a 10 cm×10 cm sensitive area has been constructed to further study the characteristics of the neutron scintillator detector.     

Monte-Carlo simulation of a compact gamma-ray detector using wavelength-shifting fibers coupled to a YAP scintillation crystal

The production and transportation of fluorescent light produced in wavelength-shifting fibers (WSFs) coupled to YAP scintillation crystal is simulated using the GEANT4 codes. An advantage of the wavelength-shifting fiber readout technique over a direct readout with a position-sensitive photo-sensor is the reduced requirement for position sensitive photomultiplier tube photocathode area. With this gamma-ray detector, the gamma camera is small and flexible and has larger effective field of view and low cost. Simulation results show that a) a mean 12 of photons per 59.5 keV gamma ray interaction is produced in the WSF located nearest to the incident gamma ray, and a spatial resolution of 3.6 mm FWHM is obtained, b) a mean 27 of photons per 140 keV gamma ray interaction is produced and a spatial resolution of 3.1 mm FWHM is obtained. Results demonstrate the feasibility of this concept of a compact gamma-ray detector based on wavelength-shifting fibers readout. However, since the very low photoelectron levels, it is very important to use a photon counting device with good single photo-electron response to readout the WSFs.     

位敏型探测器数字法读出研究(英文)

中国散裂中子源( CSNS ) 的建造对中子探测器提出了非常高的要求,如更大的有效面积、二维位置灵敏、高计数率、高探测效率和低的 灵敏度等。与传统的模拟读出方法相比,数字法读出具有更高的计数率, 更小的数据传输量,更简单的电子学设计以及更高的信噪比。对数字法读出进行了理论计算,利用GEM探测器的原始数据分析了数字法读出的位置分辨率与读出条宽度的关系。结果表明,数字法读出对于位置分辨要求较低( 小于4 mm) 的大面积位置灵敏探测器是一种较好的选择,如CSNS 小角谱仪探测器。Efficient thermal neutron detectors with large area, two-dimensional position sensitive, high counting rate high detection efficiency and low gamma sensitivity are required to satisfy the demands for the China Spallation Neutron Source (CSNS). Compared with the traditional analog readout method, the digital readout method has the advantages of higher counting rate, smaller quantity of data transmission, simpler readout system and higher signal to noise ratio. The theoretical analysis of the digital readout method is reported in this paper. Used the raw data of GEM detector, the relationship between the position resolution and the width of the readout strip was studied. The results indicate that the digital readout method could be a good choice for the large area position sensitive detector where the requirement of position resolution is less than 4 mm, e.g. the detector of Small-Angle Neutron Scattering (SANS) diffractometer of CSNS.     

A position resolution MRPC for muon tomography

Muon tomography is a promising method in the detection and imaging of high Z material. In general, considering the quality of track reconstruction in imaging, a detector of good position resolution, high efficiency and large area is required. This paper presents the design and study of a prototype of position sensitive MRPC with 0.15 mm narrow gas gap and 2.54 mm strip readout. Through a cosmic-ray experiment, the performance of MRPC module is carefully observed and each channel is calibrated. Through an X ray experiment with a narrow slit, the position resolution is studied. The results show that the time resolution of the module can reach 61ps and the spatial resolution can reach 0.36 mm.     

Study of a multi-wire proportional chamber with a cathode strip and delay-line readout

The design principle for a multi-wire proportional chamber with a cathode strip and delay-line readout is described. A prototype chamber of a size of 10 cm×10 cm was made together with the readout electronics circuit. A very clean signal with very low background noise was obtained by applying a transformer between the delay-line and the pre-amplifier in order to match the resistance. Along the anode wire direction a position resolution of less than 0.5 mm was achieved with a ^55Fe-5.9 keV X ray source. The simple structure, large effective area and high position resolution allow the application of a gas chamber of this kind to many purposes.     

Study on the imaging ability of the 2D neutron detector based on MWPC

A 2D neutron detector based on 3 He convertor and MWPC with an active area of 200 mm×200 mm has been successfully designed and fabricated.The detector has been tested with Am/Be neutron source and with collimated neutron beam with the wavelength of =1.37.The best spatial resolution of 1.18 mm(FWHM) and good linearity were obtained.This is in good agreement with theoretical calculations.     

Design and performance of a 2-D multi-wire position sensitive X-ray detector

A 2-D multi-wire position sensitive detector for X-ray diffraction and small angle X-ray scattering studies is described. The detector has an active area of 100 mm × 100 mm and consists of an anode plane with 10 μm SS wires at 3 mm spacing and a pair of orthogonal cathode readout planes with 25 μm SS wires placed at 1.5 mm spacing. The position information is obtained using charge division method and recorded using a laboratory built data acquisition system. The resolution and gas gain was measured for 5.9 keV X-rays (⁵⁵Fe-source) as a function of the anode wire voltage and gas pressure. It was observed that the proportional region of the PSD at 100 kPa pressure extended up to a high voltage value of around 1.5 kV and it shifted to high values up to 2 kV for gas pressure of 300 kPa. The energy resolution improved from 18% (FWHM) to 12% with increase in pressure. The spatial resolution of the PSD also showed improvement, with a value of 1.2 mm × 1.4 mm at 300 kPa gas pressure. A maximum gain of 5 × 10⁴ is obtained.     

基于LC延迟电路的双层多丝正比室的研制

描述了为兰州放射性粒子束流线（RIBLL Ⅱ）上测量束流径迹而研制的一种基于LC延迟电路的双层多丝正比室（MWPC）。该探测器的探测灵敏面积为100 mm×80 mm,位置信号由阴极丝引出并通过LC延迟电路读出。探测器由两套完整的多丝正比室组成,每套的阳极丝夹在两层平行的阴极丝之间,阳极丝和阴极丝相互垂直。两套阴极丝相互垂直给出入射粒子的二维位置信息。为了增大感应信号以提高探测效率,将每套位置对应的阴极丝合并成一路接入LC延迟电路。用55Fe-5.9 keV X射线源均匀照射探测器的灵敏区域,测试表明其具有良好的位置灵敏一致性。用X射线源通过准直狭缝扫描整个探测器的灵敏区域,得到X,Y层的位置线性度均好于0.999;其位置分辨（σ）分别为199.9 μm和154.0 μm,目前,该探测器已成功用于RIBLL Ⅱ的实验中。A double-layer Multi-Wire Proportional Chamber (MWPC) with 100 mm×80 mm active area has been developed for Radioactive Ion Beam Line in Lanzhou(RIBLL Ⅱ). The position information has been obtained by a LC delay circuit readout method. Being called of double-layer MWPC, it is composed of two full MWPCs, each consists of an anode plane sandwiched between two parallel cathode planes, anode wires and cathode wires are perpendicular to each other. In order to improve the detection efficiency, the cathode wires of corresponding position are combined to enhance inductive signal. The cathode wires of two full MWPCs are orthogonally placed to give two coordinates of the incident particles. The sensitivity uniformity is also found to be relatively good and the position resolution of X, Y direction are measured to be 199.9 and 154.0 μm using a 55Fe-5.9 keV X ray, respectively. The position linearity of X, Y direction are as good as 0.999 for whole sensitive area of the detector. The detector has been used successfully on the experiment at RIBLL Ⅱ.     

Investigation of high resolution compact gamma camera module based on a continuous scintillation crystal using a novel charge division readout method

The objective of this study is to investigate a high performance and lower cost compact gamma camera module for a multi-head small animal SPECT system. A compact camera module was developed using a thin Lutetium Oxyorthosilicate （LSO） scintillation crystal slice coupled to a Hamamatsu H8500 position sensitive photomultiplier tube （PSPMT）. A two-stage charge division readout board based on a novel subtractive resistive readout with a truncated center-of-gravity （TCOG） positioning method was developed for the camera. The performance of the camera was evaluated using a flood 99roTe source with a four-quadrant bar-mask phantom. The preliminary experimental results show that the image shrinkage problem associated with the conventional resistive readout can be effectively overcome by the novel subtractive resistive readout with an appropriate fraction subtraction factor. The response output area （ROA） of the camera shown in the flood image was improved up to 34%, and an intrinsic spatial resolution better than 2 mm of detector was achieved. In conclusion, the utilization of a continuous scintillation crystal and a flat-panel PSPMT equipped with a novel subtractive resistive readout is a feasible approach for developing a high performance and lower cost compact gamma camera.     

Study of a multi-wire proportional chamber with a cathode strip and delay-line readout

The design principle for a multi-wire proportional chamber with a cathode strip and delay-line readout is described. A prototype chamber of a size of 10 cm ～ l0 cm was made together with the readout electronics circuit. A very clean signal with very low background noise was obtained by applying a transformer between the delay-line and the pre-amplifier in order to match the resistance. Along the anode wire direction a position resolution of less than 0.5 mm was achieved with a 55Fe-5.9 keV X ray source. The simple structure, large effective area and high position resolution allow the application of a gas chamber of this kind to many purposes.     

Design and experimental study of a two-dimensional position sensitive X-ray detector

A prototype of a two-dimensional position sensitive X-ray detector was designed and constructed for small angle X-ray scattering experiments at BSFR (Beijing Synchrotron Radiation Facility). The detector is based on MWPC with cathode strip readout, and has a sensitive area of 200 mmx200 mm. The spatial resolution (FWHM) of about 210 μm along the anode wire direction was obtained from the 55Fe X-ray test of the detector.     

Diamond X‐ray beam‐position monitoring using signal readout at the synchrotron radiofrequency

Single‐crystal diamond is a material with great potential for the fabrication of X‐ray photon beam‐position monitors with submicrometre spatial resolution. Low X‐ray absorption combined with radiation hardness and excellent thermal‐mechanical properties make possible beam‐transmissive diamond devices for monitoring synchrotron and free‐electron laser X‐ray beams. Tests were made using a white bending‐magnet synchrotron X‐ray beam at DESY to investigate the performance of a position‐sensitive diamond device using radiofrequency readout electronics. The device uniformity and position response were measured in a 25 µm collimated X‐ray beam with an I‐Tech Libera `Brilliance' system. This readout system was designed for position measurement and feedback control of the electron beam in the synchrotron storage ring, but, as shown here, it can also be used for accurate position readout of a quadrant‐electrode single‐crystal diamond sensor. The centre‐of‐gravity position of the F4 X‐ray beam at the DORIS III synchrotron was measured with the diamond signal output digitally sampled at a rate of 130 Msample s^?1 by the Brilliance system. Narrow‐band filtering and digital averaging of the position signals resulted in a measured position noise below 50 nm (r.m.s.) for a 10 Hz bandwidth.     

基于阻性阳极读出方法的气体电子倍增器二维成像性能

新型微结构气体探测器,如气体电子倍增器(gas electron multiplier,GEM)等,具有非常好的位置分辨率潜力(σ100μm),但是需要匹配大规模高密度的读出电子学,给探测器的建设、造价、功耗、空间利用等带来极大压力.阻性阳极读出方法可以在保持较高位置分辨率的前提下,大幅节省电子学.基于厚膜电阻工艺,一种新的阻性单元阵列结构被成功开发和应用于三级级联GEM探测器的读出阳极.该阻性阳极包括6×6个6 mm×6 mm的基本阻性单元,仅需匹配49路读出电子学.~(55)Fe放射源(5.9 keV)和X光机(8 keV)实验的结果显示探测器的位置分辨率(σ)可好于80μm,位置非线性好于1.5%.同时,探测器还获得了很好的实物成像效果.探测器的优良性能表明这种阻性阳极读出方法适用于大面积二维成像气体探测器的读出,并可用于其他探测器的读出.     

Monte-Carlo simulation of a compact gamma-ray detector using wavelength-shifting fibers coupled to a YAP scintillation crystal

The production and transportation of fluorescent light produced in wavelength-shifting fibers (WSFs) coupled to YAP scintillation crystal is simulated using the GEANT4 codes.An advantage of the wavelength-shifting fiber readout technique over a direct readout with a position-sensitive photo-sensor is the reduced requirement for position sensitive photomultiplier tube photocathode area.With this gamma-ray detector,the gamma camera is small and flexible and has larger effective field of view and low cost.Simulation results show that a) a mean 12 of photons per 59.5 keV gamma ray interaction is produced in the WSF located nearest to the incident gamma ray,and a spatial resolution of 3.6 mm FWHM is obtained,b)a mean 27 of photons per 140 keV gamma ray interaction is produced and a spatial resolution of 3.1 mm FWHM is obtained.Results demonstrate the feasibility of this concept of a compact gamma-ray detector based on wavelength-shifting fibers readout.However,since the very low photoelectron levels,it is very important to use a photon counting device with good single photo-electron response to readout the WSFs.     

X‐ray position‐sensitive duo‐lateral diamond detectors at SOLEIL

The performance of a diamond X‐ray beam position monitor is reported. This detector consists of an ionization solid‐state chamber based on a thin single‐crystal chemical‐vapour‐deposition diamond with position‐sensitive resistive electrodes in a duo‐lateral configuration. The detector's linearity, homogeneity and responsivity were studied on beamlines at Synchrotron SOLEIL with various beam sizes, intensities and energies. These measurements demonstrate the large and homogeneous (absorption variation of less than 0.7% over 500 µm × 500 µm) active area of the detector, with linear responses independent of the X‐ray beam spatial distribution. Due to the excellent charge collection efficiency (approaching 100%) and intensity sensitivity (0.05%), the detector allows monitoring of the incident beam flux precisely. In addition, the in‐beam position resolution was compared with a theoretical analysis providing an estimation of the detector's beam position resolution capability depending on the experimental conditions (X‐ray flux, energy and readout acquisition time).     

用于像素探测器的高事例率高精度TDC ASIC原型电路的设计与仿真

像素探测器因其优异的位置分辨能力在高能粒子物理实验的内径探测器中有着广泛应用,随着应用场景的发展,许多物理实验要求探测器及其读出电子学也具备高精度时间测量的能力。针对像素探测器时间测量的需求,设计完成了一款具备高事例率处理能力、高精度特点的TDC(Time-to-Digital Conversion) ASIC(Application Specific Integrated Circuit) 原型电路,将来可以作为核心组成部分集成到像素探测器前端读出ASIC中。采用粗细结合的方案完成TDC的设计,其中粗时间测量基于计数器实现,细时间测量采用TAC(Time-to-Amplitude Converter)结合ADC(Time-to-Amplitude Converter)的结构实现,基于130 nm工艺完成了原型电路的设计。对TDC进行仿真,仿真结果表明,该电路可以最多处理连续11个事例,相邻事例的最短时间间隔为500 ps,bin size达到了2 ps,DNL(Differential Non-Linearity)小于2.8 ps,时间测量精度好于5 ps RMS。