壳聚糖单体溶胶凝胶煅烧合成LiFePO4/C正极

本文以壳聚糖单体为碳源兼凝胶剂,利用溶胶-凝胶煅烧合成了锂离子电池LiFePO₄/C正极材料,使用XRD和SEM对合成的材料进行表征. 用恒电流充放电测试了LiFePO₄/C电极的电化学性能,当壳聚糖单体与LiFePO4摩尔比为1:1.2时,600 ^oC煅烧的LiFePO4/C电极性能最佳,其粒径分布均匀（200 ～ 400 nm）,该电极0.2C倍率放电比容量为155 mAh.g^-1,30周期循环放电比容量仍保持152 mAh.g^-1,库仑效率为97.9 %.     

PEG分子量对LiFePO_4/C纳米复合正极材料结构与电化学性能的影响

以聚乙二醇(PEG)为纳米结构控制剂和碳源,采用液相法合成了纳米复合正极材料LiFePO4/C,其结构与电化学性能经XRD,SEM和恒电流充放电测试等表征。考察了4种不同分子量的PEG对LiFePO4/C晶型结构、粒径、形貌及充放电性能的影响。结果表明:随着PEG分子量的增大,LiFePO4/C的粒径减小、电导率增大、电化学性能提高。以PEG 4000合成的LiFePO4/C(Fd)的粒径小于50 nm,电导率为8.58×10-4S.cm-1,0.1C倍率下首次放电比容量高达165.8 mAh.g-1,循环20次后容量无衰减;1C倍率下,首次放电比容量为108.1 mAh.g-1,表明Fd具有优良的倍率性能。     

聚苯胺掺杂对C-LiFePO_4复合正极材料性能的影响

应用固相反应法在惰性气氛下合成橄榄石型LiFePO4,然后制成聚苯胺掺杂C-LiFePO4复合正极材料.XRD,交流阻抗及电化学方法等测试表明,聚苯胺掺杂对LiFePO4电化学性能有一定的改善.当放电倍率为0.1C时,掺杂10%聚苯胺的(C-LiFePO4)0.9(PANI)0.1样品的放电容量达到164 mAh.g-1,且循环稳定性良好.在0.5C和1C的放电倍率下,也可以分别达到121.6 mAh.g-1和110.1 mAh.g-1的放电比容量.     

纳米级LiFePO_4材料的水热模板法合成及其性能研究

采用水热模板法合成纳米级LiFePO4材料,改变水热反应中表面活性剂(十六烷基三甲基溴化铵)的比例控制样品颗粒生成的大小.SEM测试表明,合成的LiFePO4晶粒尺寸与表面活性剂的配比密切相关,范围在几十到几百nm之间.充放电试验表明,合成的纳米级LiFePO4材料电极具有优良的电化学性能,其0.1C放电最高比容量可达150 mAh/g,而1C和2C放电比容量也分别有140 mAh/g和126 mAh/g.     

掺碳制备锂离子电池正极材料LiFePO4

采用固相法合成LiFePO4和掺碳的LiFePO4,并对不同掺碳量的LiFePO4进行电化学性能测试,室温条件下,在0.1 C倍率下充放电,样品d(ωC=8.5%)的初始放电容量为151.7 mA·h/g.10次循环后,其放电比容量仍有149.5 mA·h/g,容量损失较小.这表明,在合适的制备工艺条件下,掺碳能获得结构稳定、电化学性能良好的锂离子电池正极材料LiFePO4.     

不同碳源对多孔球形LiFePO4/C复合材料的影响

采用喷雾干燥-碳热还原法(SDCTM),分别研究了无机和有机碳源对锂离子正极材料LiFePO4/C形貌、结构及其充放电性能的影响。结果表明:以无机碳源炭黑制备的LiFePO4/C呈不规则球形,一次颗粒粒径在800nm左右,比表面积为2m2·g-1,0.1C放电比容量为107.3mAh·g-1。而以有机碳源制备的LiFePO4/C,其形貌较为规则,呈多孔球形结构,具有较高的比表面积和放电比容量。其中,以柠檬酸为碳源制备的多孔球形LiFePO4/C复合材料,其孔径均在50nm左右,比表面积可达32m2·g-1;在室温下,0.1C和10C首次放电比容量分别为158.8和87.2mAh·g-1,具有优异的循环性能和高倍率充放电性能。     

pH对溶胶-凝胶法制备的锂离子电池正极材料磷酸铁锂的形貌及电化学性能的影响

采用溶胶-凝胶法制备了锂离子电池正极材料LiFePO_4;探讨了pH对磷酸铁锂的形貌及电化学性能的影响.结果表明,随着pH的升高,LiFePO_4的粒径减小,粒径分布变窄,电化学性能提高.在不同pH下制备的LiFePO_4材料以0.2C的倍率放电,首次放电比容量分别为126.8mAh/g、132.4mAh/g、145.6mAh/g.     

高比能LiFePO4的制备及性能研究

应用液相沉淀法-固相烧结法制备高密度的LiFePO4/C及纯相LiFePO4.X射线衍射、扫描电镜、傅立叶红外光谱仪、电化学性能测试表明:该样品具有单一的橄榄石结构和3.4 V左右的放电平台,掺碳的LiFe-PO4具有更优良的性能,粒度较小粒径分布均匀,振实密度达1.46 g/cm3,0.1C首次放电比容量为144.6mAh/g,循环20次后容量保持率为93.2%,1C倍率首次放电比容量为133.5 mAh/g,循环20次后容量下降8.76%.     

溶胶凝胶法合成LiCuVO4及其电化学性能研究

以CH3COOLi.2H2O、Cu(NO3)2.3H2O、V2O5和双氧水(30%)为原料,采用溶胶凝胶法合成了LiCuVO4,其结构、组成和形貌经XRD和SEM确认。结果表明,本文所合成的LiCuVO4具有隧道结构的形貌,颗粒粒径为0.2～6μm。将LiCuVO4作为锂离子电池正极材料,首次循环的放电比容量达到160mAh/g;而作为负极材料,其最大放电比容量达到481mAh/g。在两种电化学测试中,LiCuVO4都显示了良好的循环性能。     

球磨微波法制备Li3V2（PO4）3/C及其电化学性能表征

本文采用球磨微波法合成锂离子电池正极材料Li3V2(PO4)3/C,并研究了微波辐射时间对样品电化学性能的影响.结果表明,640 W微波辐射18 min合成的材料,结晶度高,粒径小而均匀.该电极5C倍率下首次放电比容量达101.3 mAh·g-1,300周期循环,其放电比容量仍保持100.8 mAh·g-1,展示出良好的应用前景.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

解决能源问题的新途径--光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。