HL-2A装置送气和加料的脱靶特性

HL-2A装置辐射偏滤器实验采用边缘补充送气和分子束加料等方法来提高主等离子体密度,降低边缘等离子体温度、增加辐射功率分额,获得脱靶等离子体。偏滤器室内进行主动补充送气或者注入惰性气体杂质,降低偏滤器等离子体温度,获得脱靶等离子体,并首次获得了超声分子束注入产生脱靶等离子体的实验结果。利用HL-2A装置偏滤器同一极向截面内外中性化板上安装的嵌入式探针阵列和偏滤器室安装的电动探针系统,测量了偏滤器靶板上和偏滤器室的等离子体参数及其分布,并进行了相关分析和改善约束以及偏滤器脱靶等离子体运行模式下等离子体行为的研究。     

HL-2A 装置超声分子束注入缓解偏滤器靶板上边缘局域模热通量研究

在HL-2A 装置上优化和发展了偏滤器靶板上的红外测温系统,并利用该系统分析了高约束模放电期间边缘局域模的热沉积分布特性。在高约束模式放电期间,超声分子束注入使边缘局域模所引起的偏滤器靶板上瞬间热通量峰值下降了~60%,并伴随着边缘局域模爆发频率增加了2~3 倍,而等离子体储能仅下降了~8%。分析结果表明,大幅度的丝状结构在超声分子束注入之后得到了有效抑制,沉积到偏滤器靶板上的瞬间热通量峰值也随之下降。此外,在超声分子束注入之后偏滤器室内的热辐射损失大幅度增加,从而耗散了热输运所携带的部分能量,进一步分散了沉积到偏滤器靶板上的能量,有效地保护了偏滤器靶板。     

HL-2A װ�ó���������ע�뻺��ƫ�����а��ϱ�Ե����ģ��ͨ���о�

在HL-2A 装置上优化和发展了偏滤器靶板上的红外测温系统,并利用该系统分析了高约束模放电期间边缘局域模的热沉积分布特性。在高约束模式放电期间,超声分子束注入使边缘局域模所引起的偏滤器靶板上瞬间热通量峰值下降了~60%,并伴随着边缘局域模爆发频率增加了2~3 倍,而等离子体储能仅下降了~8%。分析结果表明,大幅度的丝状结构在超声分子束注入之后得到了有效抑制,沉积到偏滤器靶板上的瞬间热通量峰值也随之下降。此外,在超声分子束注入之后偏滤器室内的热辐射损失大幅度增加,从而耗散了热输运所携带的部分能量,进一步分散了沉积到偏滤器靶板上的能量,有效地保护了偏滤器靶板。     

HL-2A装置偏滤器位形超声分子束注入深度观测

用22道Hα辐射测量阵列观测了HL-2A装置偏滤器位形超声分子束的注入过程。观测结果表明：在HL-2A装置偏滤器位形下,当分子束注入气源压强大于1MPa时,Hα辐射沿径向分布存在两个峰值,其第二个Ha辐射峰值位于r/a~0.8附近,表明大部分氢粒子在等离子体边缘(SOL区域)即被离解或电离,但仍有部分氢粒子沉积在分界面内5cm。     

Favourable scenarios established by SMBI for the realization of the ELMy H-mode at HL-2A

The ELMy H-mode plasmas realized with the supersonic molecular beam injection(SMBI) are studied in relation to the energy confinement and the heating power for the L–H transition(P_(L-H) ) in the HL-2A tokamak. A database is assembled for this study based on the ELMy H-mode discharges during the experimental campaigns in the period 2009–2013at the HL-2A tokamak. The statistical results show that the SMBI is favourable for reaching the H-mode by reducing the heating power at the L–H transition and for the H-mode performance by improving the energy confinement compared with the ordinary gas puffing(GP). The reduction of P_(L-H) is about 20% when the density is low, and the energy confinement enhancement factor of H_(H98y2)= τ_E/τ_(th,98y2) ≈ 1.5 is achieved with the SMBI. Note that in the database the density dependence of P_(L-H) is non-monotonic with the ˉne,min≈ 3×10~(19) m~(-3) at which the P_(L-H) is minimum. Most of P_(L-H) data are on the low density branch where the P_(L-H) increases with the decrease in density. The minimum of the P_(L-H) in HL-2A is comparable to the ITPA multi-machine threshold power scaling P_(thr■scal08). The physics behind the reduction of the P_(L-H) with the SMBI is also investigated in relation to the change of the density gradient at the plasma edge, the gas fuelling efficiency, and the recycling.     

HL-2A����������ȷ������

对HL-2A装置限制器位形和偏滤器位形下放电气体分别为氘和氦时的等离子体热辐射测量结果做了初步分析,分析结果表明：在偏滤器室注入惰性气体能够有效的降低到达靶板的热辐射;超声分子束注入时,观测到注入粒子在等离子体中输运过程;氦放电时的辐射比值明显高于氘放电时的比值;真空室器壁的处理能够有效地降低辐射损失,硅化对器壁条件的改善效果明显。     

辅助加热下HL-2A边界层等离子体数值模拟

以二维边界等离子体流体模拟代码B2.5为核心,编制适合于具有封闭偏滤器位形特征托卡马克的边界层网格划分代码和计算后处理代码.模拟分析HL-2A托卡马克有约3MW辅助加热功率时的边界等离子体特性.结果表明,偏滤器靶板前形成了致密低温等离子体,偏滤器运行于高再循环状态.     

中国环流器二号A(HL-2A)超声分子束注入最新结果

HL-2A装置电子回旋共振加热时,氘脉冲超声分子束穿越分界面,等离子体各项重要参数,包括等离子体储能、极向比压、中平面线平均密度、中心密度和温度上升,中子产额急剧增加. 超声分子束注入有可能较常规脉冲送气在台基顶部提供较强的粒子源,被认为是可供ITER替换脉冲送气的加料方法之一. HL-2A装置氢超声分子束注入的平均速度约为1.7km,与溢流(分子流)注入真空的速度测量作了比较. 关键词： 超声分子束注入 托卡马克 飞行时间法 加料     

Analyses of edge plasma characteristics in HL-2A

The edge plasma characteristics are studied by both a movable array of Mach/Reynolds stress/Langmuir 10-probes in the boundary region and the fixed flush probe arrays on the 4 divertor neutralization plates at the same toroidal cross-section in the HL-2A tokamak. The dependence of the Reynolds stress on poloidal flow in the edge plasma is analysed. The result indicates that the sheared poloidal flow in tokamak plasma can be induced by the radial gradient of Reynolds stress. In the divertor experiments of HL-2A, the profiles of the electron temperature, density and floating potential on divertor plates are measured by the flush probe arrays. The edge electron temperature in divertor configuration is higher than that in limiter configuration. The temperature asymmetry between outer and inner target plates is observed. The result of magnetic surface reconstructed from 18 Mirnov coils signals is presented. Both the particle recycling and the impurity flux in the bulk plasma during divertor discharges are discussed. Neutral gas pressure in divertor chamber, measured by fast ionization gauge during divertor discharge, is given.     

Density and impurity profile behaviours in HL-2A tokamak with different gas fuelling methods

The electron density profile peaking and the impurity accumulation in the HL-2A tokamak plasma are observed when three kinds of fuelling methods are separately used at different fuelling particle locations. The density profile becomes more peaked when the line-averaged electron density approaches the Greenwald density limit n_G and, consequently, impurity accumulation is often observed. A linear increase regime in the density range n_e< 0.6n_G and a saturation regime in n_e > 0.6n_G are obtained. There is no significant difference in achieved density peaking factor f_ne between the supersonic molecular beam injection (SMBI) and gas puffing into the plasma main chamber. However, the achieved f_ne is relatively low, in particular, in the case of density below 0.7n_G, when the working gas is puffed into the divertor chamber. A discharge with a density as high as 1.2n_G, i.e. n_e = 1.2n_G, can be achieved by SMBI just after siliconization as a wall conditioning. The metallic impurities, such as iron and chromium, also increase remarkably when the impurity accumulation happens. The mechanism behind the density peaking and impurity accumulation is studied by investigating both the density peaking factor versus the effective collisionality and the radiation peaking versus density peaking.     

HL-2Aװ�õ�ECRHʵ���ƫ��������

用HL-2A装置下偏滤器靶板上的14组嵌入式静电三探针阵列和外偏滤器室的电动扫描四探针组,测量了同一环向截面的内外中性化板上的电子温度、密度、悬浮电位及其分布,以及电子回旋加热(ECRH)实验期间的等离子体行为。研究了偏滤器中等离子体参数的分布及非对称性以及等离子体的形成、物理特性和改善粒子的约束特性。     

HL-1M装置高气压超声分子束加料效果

超声分子束注入作为一种新的托卡马克加料方法,已成功地开发和应用于环流器新一号(HL1M)和超导托卡马克HT7.近期开展的高气压超声分子束注入实验,在束流中发现了团簇流,其注入等离子体深度超过17cm.电子密度上升率接近于小型冰弹丸加料.多脉冲超声分子束注入形成电子密度阶梯形上升,类似于多弹丸加料效果,电子温度剖面呈中空分布.描述了在HL1M装置同一次欧姆放电等离子体中超声分子束与冰弹丸加料效果的实验比较. 关键词： 超声分子束 托卡马克 团簇 加料     

Tokamak Experiment and Tokamak Engineering——Development of the Plasma Diagnostics on HL-2A Tokamak

The main mission the HL-2A tokamak is of the experiments on to explore the divertor physics and to investigate the plasma confinement, transport and instabilities with high power auxiliary heating and advanced fuelling, it is necessary to develop more new diagnostics and increase the spatial and temporal resolutions of the measurements for exist system. Up to now, about 30 diagnostic systems have been moved from HL-1M to HL-2A tokamak. Other 10 diagnostic systems are being designed and installed on the device. In developed in last 2 years, will be presented.     

HL-2A偏滤器运行模式的探针测量

在HL-2A装置的偏滤器位形运行模式下,用偏滤器靶板上的平面型嵌入式静电探针阵列测量了同一环截面的内外和上下四个中性化板上的电子温度、密度、悬浮电位分布。偏滤器运行模式下的边缘电子温度高于孔栏运行模式下的边缘的电子温度。比较了内外靶板之间的温度不对称性。给出了由18个米尔诺夫线圈信号重建获得的磁分界面,并用强磁场快速电离规测量了偏滤器室的中性气体压强变化。测量结果表明,在偏滤器运行模式下,主真空室中边缘粒子再循环降低,杂质通量水平下降。     

HL-2Aװ�ñ�Ե�Ŷ����Թ۲�

用中平面往复快速扫描6探针组观测HL-2A装置边缘等离子体的扰动特性。在一次放电中能测量到边缘等离子体参数的时空分布及其涨落量，雷诺胁强与极向流和带状流的关系，以及静电涨落驱动的粒子通量和热通量的径向变化。在多发弹丸注入(MPI)和多脉冲超声分子束注入(SMBI)条件下，研究了边缘参数的涨落和相关特性。实验结果表明：SMBI和MPI等注入手段改变了边缘的扰动特性；雷诺胁强的径向梯度可以驱动带状流，抑制湍流输运。     

HL-2A装置偏滤器室中性气体压强的初步研究

HL-2A装置上首次实现了偏滤器位形放电。采用专门研制的可在强磁场和强噪声环境下工作的快响应真空电离规对偏滤器室内的中性气体压强进行了测量,给出了HL-2A装置偏滤器有关结构的基础数据。初步研究了偏滤器位形和孔栏位形放电期间偏滤器室中性气体压强的特性。     

HL-2A托卡马克超声分子束注入深度和加料效果研究

超声分子束注入深度与加料效率是分子束加料研究中的基本课题.在近期开展的超声分子束注入实验中，发现分子束注入深度与等离子体电子温度和密度、分子束源的气压和温度有直接关系，获得了分子束注入深度的定标律.在低温气体源(液氮冷却)的分子束注入实验中，发现分子束流中形成了团簇，其注入深度超过30 cm，分析了在低温气源分子束注入实验中的团簇现象. 关键词： 超声分子束注入 注入深度 加料效率 团簇     

Radial transport dynamics studies of SMBI with a newly developed TPSMBI code

In tokamak plasma fueling, supersonic molecule beam injection(SMBI) with a higher fueling efficiency and a deeper penetration depth than the traditional gas puffing method has been developed and widely applied to many tokamak devices.It is crucial to study the transport dynamics of SMBI to improve its fueling efficiency, especially in the high confinement regime. A new one-dimensional(1D) code of TPSMBI has also been developed recently based on a six-field SMBI model in cylindrical coordinate. It couples plasma density and heat radial transport equations together with neutral density transport equations for both molecules and atoms and momentum radial transport equations for molecules. The dominant particle collisional interactions between plasmas and neutrals, such as molecule dissociation, atom ionization and charge-exchange effects, are included in the model. The code is verified to be correct with analytical solutions and also benchmarked well with the trans-neut module of BOUT++ code. Time-dependent radial transport dynamics and mean profile evolution are studied during SMBI with the TPSMBI code in both slab and cylindrical coordinates. Along the SMBI path, plasma density increases due to particle fuelling, while plasma temperature decreases due to heat cooling. Being different from slab coordinate, the curvature effect leads to larger front densities of molecule and atom during SMBI in cylindrical coordinate simulation.     

HL-2A偏压偏滤器物理设计

根据已有的理论模型,推算出了HL-2A偏压偏滤器的理论电流为1．5kA、偏压电压为200V,并对HL-2A偏压偏滤器做出了初步设计。HL-2A装置采用偏压后,有可能降低L-H模转变阈功率,增加偏滤器等离子体密度、压强和滞留时间,改善约束,改善内外靶板功率沉积的非对称性,提高排灰效率及提高偏滤器性能。