树形结构Si/ZnO纳米线阵列的制备及光学性能

用一种低成本的方法制备出了树形结构Si/ZnO纳米线阵列。首先在室温条件下用金属辅助化学腐蚀法在Si(100)衬底上制备了Si纳米线阵列,Si纳米线的直径尺寸及分布都很均匀,通过改变腐蚀时间,能够得到高度不同的Si纳米线阵列。利用磁控溅射在Si纳米线表面制备一层ZnO薄膜,然后利用水热法在Si纳米线阵列上生长了ZnO纳米线。通过扫描电子显微镜(SEM)、能谱分析仪(EDS)和光致发光(PL)测试对样品进行了表征。通过这种方法制备的Si/ZnO复合结构在太阳能电池、光催化等领域有潜在应用价值。     

ZnO纳米线的合成与生长机理

采用化学气相沉积系统制备ZnO纳米线,以覆盖一层约5nm厚的Ag薄膜的单晶Si(001)为衬底,纳米线的生长遵循气-液-固(VLS)机理。对得到的样品采用X射线衍射(XRD)和扫描电镜(SEM)进行晶体结构和形貌的表征。XRD结果表明衬底温度在600~700℃时生长的ZnO纳米线具有六方结构和统一的取向。通过扫描电子显微镜分析,比较了生长温度对纳米线直径和长度的影响。实验表明我们可以通过催化剂和温度来实现ZnO纳米线生长的可控。与传统的VLS生长方式不同的是在我们制备的ZnO纳米线顶端并没有看到催化剂颗粒,表明纳米线的生长方式是底部生长,我们对其生长机理进行了研究。     

退火对ZnO薄膜光学特性的影响

用射频磁控溅射法在蓝宝石衬底上制备出ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了退火温度对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度和平均晶粒尺寸增大,(002)XRD峰半高宽(FWHM)减小,光致发光紫外峰强度增强。结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量ZnO薄膜。     

ZnO/Zn界面对纳米ZnO薄膜光学性质的影响

采用氧等离子体辅助电子束蒸发金属Zn后低温退火的方法制备纳米ZnO薄膜。利用X射线衍射(XRD)谱、拉曼(Raman)谱、X射线光电子能谱(XPS)以及光致发光(PL)谱等手段,分析了退火温度及ZnO/Zn界面对样品的结构和发光性质的影响。Raman结果表明随着退火温度的升高,界面模式(Es)振动减弱并向低波数方向移动。当退火温度为400℃时,界面振动消失,Zn全部转化成具有六方纤锌矿结构的ZnO,得到化学配比的纳米ZnO薄膜。PL谱表明,经400℃退火处理的样品紫外发射最强,发光性质最好。     

Pd颗粒表面修饰ZnO纳米线阵列的制备及其气敏特性

采用化学气相沉积(CVD)方法在SiO_2/Si衬底生长了ZnO纳米线阵列,纳米线长约为15μm,直径为100~500 nm。通过改变溅射沉积时间(0~150 s),在ZnO纳米线表面包覆了不同厚度的Pd薄膜。在Ar气氛中,经800℃高温退火后,制备出Pd颗粒表面修饰的ZnO纳米线阵列并对其进行了气敏测试。对于乙醇而言,所有传感器最佳工作温度均为280℃。溅射时间的增加(3~10 s)导致ZnO纳米线表面Pd纳米颗粒数量及尺寸增加,传感器响应值由2.0增至3.6。过长的溅射时间(30~150 s)将导致Pd颗粒尺寸急剧增大甚至形成连续膜,传感器响应度显著降低。所有传感器对H2均表现出相对较好的选择性,传感器具有较好的响应-恢复特性和稳定性。最后,探讨了Pd颗粒表面修饰对ZnO纳米线阵列气敏传感器气敏特性的影响机制。     

高取向As掺杂ZnO纳米线阵列的制备与表征

在不采用任何金属催化剂的条件下,运用化学气相沉积法,在Si(100)衬底上制备出高取向的As掺杂ZnO纳米线阵列.样品的X射线衍射(XRD)谱显示获得了单一取向的衍射峰,表明样品具有较好的结晶质量.场发射扫描电镜(FE-SEM)观察表明,As掺杂ZnO纳米线阵列具有均一的直径和长度,其顶部和根部直径分别为70 nm和1...     

海胆状ZnO纳米线阵列的制备及其光学性能

采用一种低成本的有效方法制备出了有序排列的海胆状ZnO纳米线阵列。首先利用自组装的方法得到了单层的聚苯乙烯(PS)小球,以其为模板用水热法在小球表面生长ZnO纳米线,得到了由PS小球和ZnO纳米线构成的海胆状结构。纳米线的直径均一,长度可通过水热反应时间进行控制。利用这种方法制备的一维ZnO纳米结构在传感器、太阳能电池及光催化领域有潜在的应用价值。     

联合体驱使生长法制备ZnO纳米棒及其表征

在常压环境下采用联合体驱使生长(Aggregation-driven growth)法在镀有ZnO纳米薄膜的医用盖玻片衬底和锌箔上制备了不同直径、高取向、密集生长的ZnO纳米棒阵列结构,发现平均直径与生长时间呈线性关系。X射线衍射(XRD)谱图中出现了较强的(002)峰,表明制备的纳米棒阵列具有高度c轴择优生长取向;高分辨透射电子显微镜(HRTEM)和选区电子花样衍射图谱(SAED)结果表明我们得到的单根纳米棒为沿(002)生长的单晶结构。分析确定盖玻片上的纳米棒阵列是以ZnO纳米薄膜缓冲层上的ZnO种子颗粒为成核点生长形成的。     

ZnO纳米线阵列的定向生长、光致发光及场发射性能

采用光刻和脉冲准分子激光沉积技术在Si衬底上制备了图形化的ZnO种子层薄膜。分别采用气相输运和水热合成法,制备了最小单元为30μm的图形化的垂直定向生长的ZnO纳米线阵列。X射线衍射(XRD)分析显示ZnO纳米线阵列具有高度的c轴[001]择优取向生长特性。从扫描电子显微镜(SEM)照片看出,阵列图形完整清晰,边缘整齐。纳米线阵列室温下光致发光(PL)谱线中在380nm左右具有强烈的紫外发射峰,可见光区域发射峰得到了抑制,证明ZnO纳米线缺陷少,晶体质量高。场致电子发射测量表明,ZnO纳米线阵列开启电场和阈值电场分别为2.3,4.2V/μm,具有较好的场致电子发射性能。     

紫外光电材料ZnO的反应溅射制备及研究

采用直流反应溅射法分别在Si(111),Si(001),及K4玻璃衬底上制备ZnO薄膜,研究了氧氩比、衬底温度以及退火处理对于晶体结晶质量的影响,发现生长过程中的退火处理提高了薄膜质量和晶面取向.通过优化生长条件,在衬底温度为350℃,氧氩比为1:2的条件下生长出了XRD半高宽为01°、C轴取向高度一致的ZnO薄膜.     

Effect of seed layer on the growth of well-aligned ZnO nanowires

We demonstrate that vertical well-aligned crystalline ZnO nanowire arrays were grown on ZnO/glass substrates by a low-temperature solution method. Different thicknesses of ZnO seed layers on glass substrates were prepared by radio-frequency sputtering. In this work it was found that the morphology of ZnO nanowires strongly depends on the thickness of ZnO seed layers. The average diameter of nanowires is increased from 50 to 130 nm and the nanowire density is decreased from 110 to 60 μm⁻² while the seed layer thickness is varied from 20 to 1000 nm. The improved control of the morphology of ZnO nanowire arrays may lead to an enhanced carrier collection of hybrid polymer photovoltaic devices based on ZnO.     

Growth mechanism studies of ZnO nanowire arrays via hydrothermal method

Well-controlled ZnO nanowire arrays have been synthesized using the hydrothermal method, a low temperature and low cost synthesis method. The process consists of two steps: the ZnO buffer layer deposition on the substrate by spin-coating and the growth of the ZnO nanowire array on the seed layer. We demonstrated that the microstructure and the morphology of the ZnO nanowire arrays can be significantly influenced by the main parameters of the hydrothermal method, such as pH value of the aqueous solution, growth time, and solution temperature during the ZnO nanowire growth. Scanning electron microscopy observations showed that the well oriented and homogeneous ZnO nanowire arrays can be obtained with the optimized synthesis parameters. Both x-ray diffraction spectra and high-resolution transmission electron microscopy (HRTEM) observations revealed a preferred orientation of ZnO nanowires toward the c-axis of the hexagonal Wurtzite structure, and HRTEM images also showed an excellent monocrystallinity of the as-grown ZnO nanowires. For a deposition temperature of 90 °C, two growth stages have been identified during the growth process with the rates of 10 and 3 nm/min, respectively, at the beginning and the end of the nanowire growth. The ZnO nanowires obtained with the optimized growth parameters owning a high aspect ratio about 20. We noticed that the starting temperature of seed layer can seriously influence the nanowire growth morphology; two possible growth mechanisms have been proposed for the seed layer dipped in the solution at room temperature and at a high temperature, respectively.     

Sol-gel synthesis of sub-50 nm ZnO nanowires on pulse laser deposited ZnO thin films

A simple synthesis route to high-quality sub-50 nm ZnO nanowires is reported, utilizing ZnO thin films grown by pulse laser deposition (PLD) as seed layers. Depending upon the PLD growth conditions, the surface morphology of the ZnO nanowires on ZnO film was distinctively different whereas the diameters were almost the same. With the increase of the concentration of zinc nitrate/methenamine solution from 0.002 to 0.02 M, the average diameter of the ZnO nanowire increased but remained sub-50 nm. The grown ZnO nanowires showed a high crystallinity with a low defect density confirmed by a sharp photoluminescence spectrum.     

Growth of self-assembled ZnO nanowire arrays

This paper reports on ZnO nanowires arrays synthesized using Sn as a catalyst. The Sn particles were produced from the reduction of SnO₂ powders via a vapour-solid growth process. Control of growth conditions led to the formation of ZnO nanowire arrays, radial nanowire ‘flowers’ and uniaxial fuzzy nanowires. ZnO nanowire–nanobelt junctions were also grown by changing the growth direction. As-grown nanowire arrays could be fundamental materials for investigating physical and chemical properties at nano-scale dimensions.     

聚苯胺/ZnO纳米线薄膜材料作为发光层的柔性光电器件 及其发光机理

综合氧化锌纳米线(ZnO NWs)的光学活性与聚苯胺(PANI)的空穴传输特性,设计并制备了一种聚合物/ZnO纳米线电致发光材料,并对其发光特性进行了研究。通过高分子络合软模板法,将有序的单晶ZnO NWs均匀生长在覆有铟锡氧化物(ITO)涂层的柔性聚乙烯对苯二甲酸乙二醇酯(PET)衬底上并嵌入PANI薄膜,获得了电致发光薄膜材料和有机/无机异质结实验器件ITO/(ZnO NWs-PANI)。有机/无机异质结器件电致发光可调,在相对低的开启电压下呈现室温蓝紫外发光,并且ZnO NWs表面覆盖PANI增加了蓝紫外发光的强度和稳定性;而无PANI的ZnO NWs阵列具有450 nm处的缺陷发射峰,这可能是电子从扩展态锌间隙Zn_i到价带的跃迁引起的。这些结果表明,基于PANI/ZnO纳米线的复合材料在柔性光电器件方面的应用极具潜力。     

Growth and characterization of type-II ZnO/ZnTe core-shell nanowire arrays for solar cell applications

Large area, well-aligned type-II ZnO/ZnTe core-shell nanowire arrays have been fabricated on an a-plane sapphire substrate. The ZnO nanowires were grown in a furnace by chemical vapor deposition with gold as catalyst and then were coated with a ZnTe shell on the ZnO nanowires surface by a metal-organic chemical deposition chamber. The morphology and size distribution of the ZnO/ZnTe core-shell nanowire arrays were studied by scanning electron microscopy (SEM) and the crystal structure was examined by x-ray diffraction (XRD). Transmission measurement was used to study the optical properties of the core-shell nanowires. The results indicated that the ZnO/ZnTe core-shell nanowire arrays have good crystalline quality. In addition, it was found that the nanowire arrays have good light absorption characteristics and these properties make it suitable for making photovoltaic devices.     

单晶ZnO纳米线的合成和生长机理研究

用化学气相输运(CVT)方法合成了直径在20～120nm呈单晶结构的ZnO纳米线.利用场发射扫描电 镜(FESEM)、高分辨透射电镜(HRTEM)以及选区电子衍射(SAED)等技术对ZnO纳米线的生长机理和结构进行 了系统研究,结果表明,纳米线的成核与Au Zn合金催化颗粒的饱和度有直接的关系,先饱和的颗粒上纳米线首 先成核.纳米线顶端合金颗粒组成的变化是导致纳米线生长终止的重要原因,大量纳米线的生长不是同时进行 的.本工作提供了支持纳米线气液固(V L S)生长机理的新实验证据,提出了氧化物纳米线的生长机理.