表面活性剂敏化的铽离子荧光探针对氧氟沙星的测定

稀土Tb3 +能与氧氟沙星形成络合物 ,并发出Tb3 +的特征荧光 ;加入表面活性剂SDBS能大大增强体系的荧光强度 ,由此建立了表面活性剂敏化的Tb3 +荧光探针测定氧氟沙星的方法。用 1cm石英比色池在激发波长为 30 0nm ,发射波长为 5 4 5nm处测定其荧光强度。在pH =5 .5～ 6 .5 ,Tb3 +浓度为 5 .0× 10 -5mol/L ,SDBS浓度为 5 .0× 10 -4mol/L的最佳测试条件下 ,氧氟沙星的浓度与体系的荧光强度呈线性关系 ,线性范围为 5 .0× 10 -8～ 2 .0× 10 -6mol/L ;检出限为 6 .0× 10 -9mol/L。该法可用于氧氟沙星药物的测定     

碳棒涂膜电极流动注射法测定环境水样中的阴离子表面活性剂

采用自制碳棒PVC涂膜阴离子表面活性剂电极 ,建立了测定环境水样中阴离子表面活性剂的流动注射电位分析新方法。电极膜最佳组成 :THDA DBS 5mg ,DBS 0 .4mL,NB 0 .3mL ,PVC粉 0 .2g;电极线性响应范围 1× 1 0 - 3～ 1× 1 0 - 6 mol L。以 0 .0 1mol LKCl溶液作载流 ,流速 6.6mL min ,进样体积 2 0 0 μL,分散管长 2 0cm ,采样频率 5 0～ 80次样 h。测定 1 0 - 3、1 0 - 4 mol LDBS溶液 ,RSD≤ 3 .1 2 % (n=7) ,回收率 88.0 %～ 1 0 5 .0 %。电极易制作 ,成本低 ,FIA流路简单 ,操作方便 ,且克服了直接电位法电位飘移大的缺点 ,有较好的实用性     

乙基曙红-溴化十六烷基吡啶光度法测定水样中阴离子表面活性剂

在弱酸性的HAC-NaAC缓冲介质中,将溴化十六烷基吡啶(CPB)与乙基曙红(EE)染料溶液混合,加入阴离子表面活性剂(AS),溶液颜色加深,最大吸收波长都在516nm处,且阴离子表面活性剂的浓度与溶液的增色程度呈良好线性关系。在最大吸收波长处,3种阴离子表面活性剂——十二烷基苯磺酸钠(SDBS)、十二烷基磺酸钠(SLS)及十二烷基硫酸钠(SDS)的浓度分别在0~2.05×10-5mol/L、0~2.08×10-5mol/L、0~2.04×10-5mol/L范围内遵守比尔定律,表观摩尔吸光系数分别为2.38×104、2.82×104和2.98×104L/(mol.cm),检出限分别为8.42×10-7、4.56×10-7和7.95×10-7mol/L。方法具有较高的灵敏度和良好的选择性,用于不同水样中AS的测定,结果满意。     

β-环糊精存在下阳离子表面活性剂的毛细管电泳电导法测定

基于H3 BO3 与 β CD配合成大阴离子 ,与不同的阳离子表面活性剂作用不同 ,建立了快速分离检测阳离子表面活性剂的毛细管电泳电导法。研究了H3 BO3 与 β CD的浓度 ,缓冲液的酸度和浓度对分离的影响。在优化的实验条件下 ,溴化四丁基铵 (TBAB)、溴化十二烷基三甲基铵 (DTAB)、溴化十六烷基三甲基铵(CTMAB)阳离子表面活性剂 10min内完全分离 ,峰形良好。线性范围分别为TBAB 10 -3 ～ 10 -5mol/L ,DTAB1.0× 10 -3 ～ 5 .0× 10 -6mol/L ,CTMAB 1.0× 10 -3 ～ 5 .0× 10 -6mol/L。检测限分别为TBAB 7.5× 10 -6mol/L ,DTAB 1.7× 10 -6mol/L ,CTMAB 1.0× 10 -6mol/L。方法用于合成水样分析 ,结果令人满意     

四种阴离子的毛细管电泳电导检测(英文)

 采用柠檬酸 柠檬酸钠作为缓冲体系 ,使用负高压 ,对Cl-,NO3 -,HCO3 -和H2 PO4 -等 4种常见阴离子进行了分离检测 ,研究了缓冲剂的种类、浓度、pH值及操作电压对分离的影响。在选定的条件下 ,4种离子的定量线性范围 :Cl-5 0× 10 -5mol/L～ 2 5× 10 -3 mol/L ,NO3 -6 0× 10 -5mol/L～ 2 0× 10 -3 mol/L ,HCO3 -5 0× 10 -6mol/L～ 2 0× 10 -4 mol/L ,H2 PO4 -6 0× 10 -5mol/L～ 1 0× 10 -3 mol/L ;检出限 :Cl-1 5× 10 -5mol/L ,NO3 -3 0×10 -5mol/L ,HCO3 -1 0× 10 -6mol/L ,H2 PO4 -2 0× 10 -5mol/L ;峰面积的RSD (n =6 ) :Cl-3 1% ,     

夜蓝与阴离子表面活性剂在水溶液中显色反应——吸光光度法测定环境水样中阴离子表面活性剂

在聚乙烯醇存在的1.8mol/L磷酸溶液中,夜蓝与阴离子表面活性剂形成离子缔合物。溶液由绿色变为蓝色,可用于水相直接光度测定阴离子表面活性剂。最大吸收波长555nm,摩尔吸光系数分别为5.72×10~4L·mol~(-1)·cm~(-1)(十二烷基苯磺酸钠),5.77×10~4 L·mol~(-1)·cm~(-1)(十二烷基硫酸钠),4.36×10~4 L·mol~(-1)·cm~(-1)(十二烷基磺酸钠)。方法简便、快速,具有良好的选择性。可用于河水和生活废水中10~(-6)—10~(-7)mol/L阴离子表面活性剂的测定。     

阻抑褪色光度法测定水样中阴离子表面活性剂

在弱酸性的HCl-NaOAC缓冲介质中,溴化十六烷基吡啶(CPB)和曙红Y(EY)染料的混合溶液发生褪色,在该褪色的溶液中分别加入十二烷基硫酸钠(SDS)及十二烷基苯磺酸钠(SDBS)等阴离子表面活性剂(AS),溶液颜色发生改变,最大吸收波长都在514 nm处,并分别在548、546 nm处产生明显褪色。在吸收或褪色波长处,阴离子表面活性剂的浓度与增色或褪色程度呈良好线性关系,从而建立测定阴离子表面活性剂的光度法。在最大吸收波长处,SDBS体系、SDS体系中AS的浓度在0~2.06×10-5mol/L、0~2.63×10-5mol/L范围内遵守比尔定律,表观摩尔吸光系数分别为1.30×104、1.01×104L.mol-1.cm-1,检出限分别为8.14×10-7、9.96×10-7mol/L。若用双波长叠加,表观摩尔吸光系数达2.07×104、1.78×104L.mol-1.cm-1,检出限为4.82×10-7、8.34×10-7mol/L。方法具有较高的灵敏度和良好的选择性,用于水样中AS的测定。     

碱性品红共振散射法测定阴离子表面活性剂

在pH 6.0 Walpole缓冲溶液中,碱性品红(FB)与阴离子表面活性剂十二烷基苯磺酸钠(SDBS)在静电引力作用和疏水作用力共同作用下形成了紫红色离子缔合微粒,其分别在258、316、358和623nm处产生4个共振散射峰,最强峰位于316nm处。于优化实验条件下,在1.0×10-7～5.6×10-5mol/L范围内,体系的共振散射信号与SDBS浓度之间呈良好的线性关系,其检出限为1.86×10-12mol/L。该方法直接用于测定生活废水中的阴离子表面活性剂含量,得到较满意的结果,回收率为96.8%～106.9%。     

新试剂4,4′-(2-氯-4-硝基重氮氨基)联苯与氯化十六烷基吡啶显色反应的研究

研究了4,4′-(2-氯-4-硝基重氮氨基)联苯与阳离子表面活性剂氯化十六烷基吡啶发生显色反应,提出了光度法测定氯化十六烷基吡啶的新方法。实验结果表明,在碱性介质中,4,4′-(2-氯-4-硝基重氮氨基)联苯与氯化十六烷基吡啶形成1∶2紫红色离子缔合物,最大吸收波长位于570 nm处,表观摩尔吸光系数为2.16×104L·mol-1.cm-1。表面活性剂的浓度在0～3.0×10-5mol/L范围内符合比耳定律。方法可直接应用于合成水样中阳离子表面活性剂的测定。     

黑火药余烬中无机阴离子的毛细管电泳方法研究

 发展了一种用于黑火药余烬中无机阴离子测定的毛细管电泳分析方法。对缓冲溶液的组成及pH值、电渗流改性剂的浓度以及分离电压等条件进行了研究。选定条件 :分离电压为 - 2 0kV ,缓冲溶液为 5 0mmol/L的Na2 CrO4(pH 8 2 0 ) ,电渗流改性剂为 0 5mmol/L的溴化十六烷基三甲基铵 (CTAB) ,检测波长为 2 5 4nm。在上述条件下 ,5种阴离子在 4min内可完全分离。各组分迁移时间和峰面积的相对标准偏差 (RSD)分别为 0 17%～1 4 0 %和 3 9%～ 5 0 % ,最低检测限为 5 0 μmol/L～ 10 0 μmol/L。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.