白果形钨酸铅的可控合成及光致发光特性

以酒石酸钠为表面活性剂,采用直接沉淀法合成了白果形钨酸铅晶体,通过扫描电子显微镜(SEM)、X射线衍射(XRD)、能量散射仪(EDS)及荧光发射光谱(PL)对产物的结构和性质进行了表征。探讨了酒石酸钠对(004)晶面的抑制作用以及pH值和陈化温度对产物形貌的影响,结合晶体的内部结构提出了产物可能的形成机制。结果表明,陈化温度为30℃时,晶体形貌最为规整,PbWO₄晶体在紫外光激发下展现出强的绿光发射,在pH=9时可达到最大的发光强度。     

不同形貌TiO2的水热合成及对苯酚的降解研究

采用水热合成法, 通过对溶液的pH值、反应物配比、陈化温度及陈化时间等条件的控制, 合成出不同晶型及形貌的TiO2纳米粒子. 结果表明, 溶液的pH＝11, n(钛酸丁酯):n(三乙醇胺)＝1:2, 陈化温度为150 ℃, 陈化时间为48 h时, 能得到较规则的、长径比约为4:1的棒状TiO2. 当溶液pH<10时, 得到球形的TiO2纳米粒子; 陈化时间为24 h时, 得到纺锤形TiO2纳米晶. 以上合成的纳米粒子均为锐钛矿型, 但当溶液的pH>12时, 则得到板钛矿型TiO2粒子. 以苯酚为降解模型, 考察了不同形貌TiO2的光催化活性.     

乙醇/水混合溶剂体系中碳酸钙晶体晶型和取向的控制

采用(NH4)2CO3分解法,制备得到了晶型和形貌可控的CaCO3晶体。研究结果表明,乙醇/水混合溶剂、陈化时间和L-半胱氨酸自组装单层模板对CaCO3晶体的晶型、取向和形貌都具有重要影响。无单层模板情况下,溶液中主要得到了球霰石,球霰石的形貌随陈化时间从花朵外形变为树叶形。同样的醇/水体系中,在自组装单层上却得到了取向为(104)晶面的方解石。这与水溶液中同一自组装单层上主要获得(001)结晶面的方解石有明显不同。方解石的形貌也随陈化时间变化而改变。陈化时间为3h时,得到具有孔洞结构的方解石;陈化时间为12 h时,得到表面光滑的菱面体方解石。     

棒状氢氧化镁的合成

以氯化镁和氢氧化钠为原料合成了棒状氢氧化镁粉体。考察了氢氧化钠浓度、陈化温度、陈化时间对氢氧化镁形貌的影响。采用SEM、HRTEM、XRD、TG等对所得氢氧化镁颗粒的形貌、颗粒大小、晶习及热稳定性进行了表征。结果表明,当陈化温度为90℃时,所得棒状氢氧化镁随氢氧化钠浓度的升高及陈化时间的增加,晶形更加完整;当陈化温度在120℃时,所得氢氧化镁颗粒的形貌为片状,不能得到棒状氢氧化镁。     

低温水热法制备高活性纳米金红石相二氧化钛

采用低温水热法由TiC l3溶液直接制备了纳米二氧化钛,并研究了TiC l3溶液浓度、反应温度以及陈化时间对产物晶相、晶化程度、形貌以及尺寸的影响。结果表明:TiC l3溶液浓度对晶相有较大影响,高浓度下易获得混晶,低浓度下得到纯金红石相。反应温度和陈化时间主要影响产物的晶化程度和晶体的形貌、尺寸,对生成的晶相也有一些影响。在给定的反应条件下,获得了形状规整、尺寸约为15×80nm、晶化程度高的金红石相二氧化钛纳米棒。对甲基橙的光催化降解实验表明,这种金红石纳米颗粒的催化活性与市售纳米锐钛矿相二氧化钛相近。     

三维分级结构氢氧化钴的合成

以硝酸钴为钴源,采用十六烷基三甲基溴化铵(CTAB)辅助,通过水热法合成了具有三维分级结构的β-Co(OH)2微球.采用粉末X射线衍射(XRD)、能谱元素分析(EDS)和扫描电镜(SEM)对产物进行表征.实验结果表明,产物β-Co(OH)2为由直径1～2μm和厚度约500nm的纳米板组装而成的微球.考察了CTAB的浓度、pH值和温度对产物形貌的影响.结果表明,CTAB的浓度和pH值对最终产物的形貌具有重要影响,而当水热温度在140～180℃区间内,反应温度对产物的形貌无影响.通过监控不同反应时间所获产物的形貌,初步探讨了三维结构的β-Co(OH)2的生长机制.     

L-半胱氨酸自组装膜诱导草酸钙结晶研究

在CaCl2.H2O和Na2C2O4配制的过饱和溶液中,利用L-半胱氨酸(L-Cys)在金片上形成的自组装膜为模板,研究了草酸钙(CaOxa)在自组装膜上的结晶行为,并探讨了溶液pH对CaOxa晶体组成、晶型及其形貌的影响。采用X射线衍射(XRD)和扫描电子显微镜(SEM)等技术对CaOxa晶体的结构和形貌进行了表征。实验结果表明:当溶液pH=3.0时,溶液中可以形成一水草酸钙(CaC2O4.H2O,COM)和二水草酸钙(CaC2O4.2H2O,COD)晶体,而在同样pH条件下,在L-Cys自组装膜上只形成COD晶体,表明自组装单层对CaOxa晶体的成核和生长有重要影响。通过改变溶液的pH,在自组装单层上可以得到不同晶型和不同形状的CaOxa晶体。当pH=3.0时得到四方块状的COD晶体,而pH=5.0和pH=7.0时分别得到六边形和拉长六边形的COM晶体。     

磷酸钙在凝胶体系中的仿生矿化研究

通过模拟牙釉质的生物矿化过程,在琼脂凝胶体系中研究两种磷酸钙晶体—磷酸八钙(Ca8H2(PO4)6.5H2O,OCP)和羟基磷灰石(Ca10(PO4)6(OH)2,HAP)的矿化过程:分别研究了不同pH值(pH=6.5,7.0,7.5)条件下以及添加I型胶原蛋白的凝胶体系中矿化所形成的磷酸钙晶体的组成和形貌。在凝胶体系中,当pH=6.5时主要形成OCP,形貌为较大尺寸的片状;pH=7.0,则形成了较短片状OCP与针状HAP的混晶;pH=7.5,则主要形成针状形貌的HAP。此外,当添加Ⅰ型胶原蛋白后,在pH=6.5时则主要形成较大尺寸的片状HAP,且互相平行排列成束。由实验结果可知:pH对凝胶体系中仿生合成的磷酸钙晶体的组成和形貌具有一定的调控作用,而Ⅰ型胶原蛋白则有利于诱导形成片状HAP晶体并且使之排列呈束状,其结构类似牙釉质晶体。     

乙醇/水混合溶剂体系中碳酸钙晶体晶型和取向的控制

采用（NH₄）₂CO₃分解法,制备得到了晶型和形貌可控的CaCO₃晶体。研究结果表明,乙醇/水混合溶剂、陈化时间和L-半胱氨酸自组装单层模板对CaCO₃晶体的晶型、取向和形貌都具有重要影响。无单层模板情况下,溶液中主要得到了球霰石,球霰石的形貌随陈化时间从花朵外形变为树叶形。同样的醇/水体系中,在自组装单层上却得到了取向为（104）晶面的方解石。这与水溶液中同一自组装单层上主要获得（001）结晶面的方解石有明显不同。方解石的形貌也随陈化时间变化而改变。陈化时间为3h时,得到具有孔洞结构的方解石;陈化时间为12h时,得到表面光滑的菱面体方解石。     

反相微乳液法合成碘化铅纳米棒

用Pb(NO3)2和KI为反应物, 在水溶液/Triton X-100/正己醇/环己烷反相微乳液体系中制得了碘化铅纳米棒. 研究了ω0(水与表面活性剂的摩尔比)、反应物浓度、反应温度及陈化时间等因素对产物尺寸和形貌的影响, 并用TEM和XRD等技术对产品进行了表征.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.