非水稀溶液中SiO2包覆ZnO量子点的制备及其发光特性研究

本文利用溶胶-凝胶法在非水稀溶液中制备出SiO₂包覆的ZnO量子点。通过紫外-可见吸收光谱(UV-Vis)和荧光光谱对合成量子点的发光特性进行了研究。结果表明，在n_SiO2:n_ZnO=1∶4的条件下，ZnO量子点的发光性能最佳。经过Brus公式计算，该量子点的平均半径在2.8 nm左右，稳定性显著提高。其荧光光谱在363 nm处有一强而窄的激子发射峰，在519 nm处有一个宽而弱的绿色发射峰。说明SiO₂对ZnO形成了有效包覆，明显减少了ZnO的表面缺陷。     

Ba2SbInO6双钙钛矿的水热合成和表征

利用水热晶化法制备了Ba₂SbInO₆纯相，并通过XRD、SEM、IR、XPS和ICP等方法，对产物的物相、形貌、结构和组成进行了表征。初步结构表征结果表明，产物可能为B位离子无序排列的立方钙钛矿结构，空间群为Pm3m，晶胞参数为a=0.4132 mm。产物粉末呈现立方晶型，粒度约为0.5～2 μm。     

超细Sr2CeO4 粉体微乳液-高温法制备条件的正交试验及其发光性能研究

本文首先利用正交试验确定了微乳液-高温法合成蓝色发光Sr₂CeO₄超细粉体的最佳制备条件。接着研究了最佳条件下制备的Sr₂CeO₄超细粉体的性能。场发射扫描电镜(FE-SEM)显示，在850 ℃、900 ℃、1 000 ℃或者更高温度下退火4 h制备的粉体的形状分别呈球状、梭状和球状，平均粒径分别在100 nm左右和1 μm以内。X射线粉末衍射数据分析表明，该超细粉体属于正交晶系。室温下的光致发光光谱显示，该粉体的激发光谱有3个激发峰，主峰分别位于262 nm、281 nm和341 nm，而其发射光谱只呈现出1个发射峰，主峰位于约470 nm。与高温固相制备方法相比，微乳液-高温法可以在较低温度下制备出超细的粉体，而且它不但在262 nm处出现了一个新的激发峰，主激发峰和发射峰的位置也分别蓝移了大约30 nm和12 nm。     

ZrO2球的准气相反应合成

提出了一种工艺简单、成本低廉的准气相反应合成ZrO₂球的新方法. 通过对产物的SEM观测表明: 该方法制备的ZrO₂粒子为较好的球形, 球表面光滑; 其平均粒径1.71 μm, 标准偏差0.49 μm; 球有三种结构: 均匀致密结构、核心疏松外层致密结构和空心结构; 经600 ℃煅烧后, XRD分析确定ZrO₂球的相组成主要为立方相.     

纳米硫化锌的生物还原-化学沉淀耦合制备及其性能表征

生物还原-化学沉淀耦合反应法制备了纳米硫化锌,采用XRD、SEM、TEM、EDS、PL、FTIR等测试手段对产物进行了结构形貌性能表征。结果表明,在加入与Zn²⁺等物质的量浓度的EDTA后,Zn²⁺对硫酸盐还原菌(SRB)的毒性消除,SRB的较快生长和SO₄^2-的高效还原得以实现,EDTA修饰的生物转化-化学沉淀耦合系统可制备出高纯的纳米硫化锌晶体。制备的纳米ZnS实心微球体形状规则、分散均匀、大小一致,一次粒子直径10～15 nm,二次粒子直径400 nm左右。光致荧光光谱和红外光谱分析显示,ZnS纳米粒子在396 nm处出现荧光发射峰,在465 nm处出现缺陷发光峰,而且具有良好的红外透过性。分散剂聚丙烯酰胺(polyacrylamide)的加入导致产物ZnS的形貌和粒度改变,二次粒子的平均直径减至100 nm以下,其荧光发射峰强度增强,红外透过性提高。     

制备方法对负热膨胀性ZrW2O8粉体的颗粒大小以及负热膨胀性能影响的研究

采用共沉淀法、分步固相法和溶胶凝胶法制备负热膨胀性ZrW₂O₈粉体。以XRD、SEM和TEM对产物结构及形貌进行表征，以原位X射线衍射分析粉体的负热膨胀特性。结果表明3种方法所制备的粉体均为单一立方结构的α-ZrW₂O₈相，共沉淀法制备的粉体颗粒较大，平均尺寸约为2.5 μm × 3.0 μm，溶胶凝胶法制备的颗粒最小，平均尺寸达到100 nm。所得粉体均表现为较强的负热膨胀特性，当粉体粒径相差不大时，负热膨胀系数变化很小，当颗粒粒径降低到纳米级时，负热膨胀系数有减小的趋势。     

一种高灵敏度高选择性的荧光素基比色荧光锌传感器

本文报道了一种基于荧光素的锌离子传感器FN1,其在甲醇溶液中显示了对锌离子极高的灵敏度和选择性。随着锌离子的滴加,紫外-可见光谱中最初在371 nm处的吸收峰消失,在437 nm处出现了一个新峰。当在混合金属离子的甲醇溶液中滴加了相对于二价金属离子的等物质的量浓度的锌离子或相对于一价金属离子0.5倍物质的量浓度的锌离子后,锌离子积分荧光强度增强了近37倍（Φ=0.48,λ_max(em)=513 nm）,估算的锌离子检测限为7 μg·L^-1。基于紫外-可见光、荧光和质谱的结果,讨论了1∶1的FN1/Zn²⁺配合物的结合机理。     

水热法制备多层核壳结构Gd2O3∶Eu3+空心微球

以稀土硝酸盐-葡萄糖的混合溶液作为前驱体,采用一步水热法和随后的热处理得到了多层核壳结构Gd₂O₃∶Eu³⁺空心微球,并用X-射线衍射(XRD)、场发射扫描电镜(FESEM)、透射电镜(TEM)、X-射线能量色散光谱(EDS)和荧光光谱等测试手段对所得样品进行了表征。结果表明：所得空心球样品为纯的立方相的Gd₂O₃。具有规则的多层核壳空心结构,空心球的直径在2~3 μm左右,壁厚约为100 nm,并且Gd₂O₃∶Eu³⁺空心球是由尺寸约为30 nm的球形纳米颗粒自组装而成。样品中含有Gd、Eu、O元素。该空心球样品具有强的Eu³⁺的特征红光发射以及长的荧光寿命,可以用来作为时间分辨荧光标记物。     

ZnS纳米球的水热法制备及其光催化性能研究

在表面活性剂十六烷基三甲基溴化铵(CTAB)的辅助下,以乙酸锌为锌源,硫脲(NH₂)₂CS为硫源,使用水热法通过改变反应时间,成功制备了不同粒径的ZnS球状颗粒.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能谱,高分辨透射电子显微镜(HRTEM))、紫外可见分光光谱和光致发光谱(PL)等测试手段对样品的晶体结构、形貌、光学性质进行了分析.通过对不同粒径的ZnS纳米颗粒对亚甲基蓝的光催化降解的催化活性进行了评估.实验结果表明:在表面活性剂CTAB的作用下,随着反应时间的增加,生成的ZnS晶核生长成纳米颗粒,然后ZnS纳米颗粒将进一步发生团聚从而形成平均粒径超过500nm的ZnS纳米球,但制备的ZnS产物的晶体结构均为立方纤锌矿结构.随着ZnS粒径的增加,样品的紫外吸收峰从418nm逐渐蓝移到362nm,而PL发射峰位的峰强随着粒径的增大而增强.光催化结果显示,反应12h制备的ZnS纳米球的光催化性能最佳.     

二氧化锰纳米颗粒调控的紫外可见吸收-荧光双通道传感器的构建及D-青霉胺的检测

以聚乙烯亚胺(PEI)同时作为模板和还原剂,基于原位氧化还原反应,一步法制备二氧化锰纳米颗粒(MnO₂ NPs),并对其形貌、组成、紫外可见吸收、催化氧化特性进行了表征。结果表明,MnO₂ NPs能够催化氧化邻苯二胺(OPD)为2,3-二氨基吩嗪(DAP),产生420 nm处的紫外可见吸收和560 nm处的荧光发射。D-青霉胺(DPA)中的活性巯基可与MnO₂发生特异性反应,还原降解催化剂,抑制其催化氧化活性,使得体系紫外可见吸收-荧光信号减弱甚至消失。基于DPA浓度与体系光谱信号变化的关系,我们建立了MnO₂ NPs介导的紫外可见吸收-荧光双通道传感DPA的新方法。荧光传感通道具有更好的线性范围和灵敏度,该方法线性范围为1~80 μmol·L^-1,检出限为0.54 μmol·L^-1。此外,MnO₂ NPs介导的荧光传感DPA应用于人体尿液样品分析中的回收率为98.31%~107.76%,证明了该方法的可靠性。     

Selected-control solution-phase route to multiple-dendritic and cuboidal structures of PbSe

Well-crystalline PbSe multiple-dendritic hierarchical structures have been prepared through a facile hydrothermal process in an alkaline glycerol/water solution system using SeO₂ as selenium source and hydrous hydrazine as reducing agent at 160 °C for 12 h. The obtained products were characterized by X-ray powder diffraction, field emission scanning electron microscopy and transmission electron microscopy, which showed that the obtained products were face-centered cubic PbSe multiple-dendritic superstructures with length of each dendrite ranging from 1.0 to 1.5 μm. Additionally, cuboidal PbSe microcrystals with different concave faces can be obtained through a similar process except for using Se powders instead of SeO₂ as selenium source and without hydrous hydrazine. The edge lengths of these cuboidal microcrystals range from 1.0 to 2.5 μm observed by field emission scanning electron microscopy. The influencing factors for the formation of the two kinds of PbSe microstructures were discussed and the possible growth mechanisms were proposed from the point of crystallographic and kinetic views. The studies on the corresponding photoluminescence (PL) properties of the two kinds of PbSe structures are also carried out.     

Fabrication of symmetric hierarchical hollow PbS microcrystals via a facile solvothermal process

Symmetric hierarchical hollow PbS structures consisting of nanowalls were successfully fabricated by a facile solvothermal process in ethylenediamine at 120 degrees C for 12 h, employing lead acetate trihydrate and dithizone as precursors; the thickness of the nanowalls is about 80 nm. No surfactants or other templates were used in the process. The synthesized product was characterized by X-ray powder diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron diffraction (ED), ultraviolet-visible spectrometer (UV-vis), near-infrared absorption spectroscopy (near-IR), and fluorescence spectrophotometer. The effect of the reaction conditions on the size and morphologies of PbS structures was investigated. The results show that the temperatures, solvent, and sulfur sources are crucial factors on the morphologies and sizes of the symmetric hierarchical hollow PbS microcrystals. A possible growth mechanism of hierarchical hollow PbS structures is presented. UV-vis absorption spectrum holds a weak peak at 253 nm; the near-infrared absorption spectrum of PbS microcrystals has the two absorption peaks centered at 9613 cm(-1) (1040 nm) and 6771 cm(-1) (1477 nm), showing a blue shift compared with the bulk PbS (approximately 3020 nm). And the fluorescence spectrum of PbS microcrystals consists of an emission peak with a maximum at 305 nm. These PbS microcrystals may have potential applications in the fundamental study of nanostructures as well as fabricating nanodevices.     

简易、可控制备硫化铅纳米带

以硝酸铅和硫代乙酰胺为前体,十二烷基苯磺酸钠（SDBS）扮演了前体和表面活性剂的双重角色,制备出硫化铅纳米带。 采用透射电子显微镜、X射线衍射和光致发光对所制备的纳米带进行了表征。 结果表明,中间产物PbSO4在水热条件下对PbS纳米带的进一步形成主要起到模板作用。 进一步考察了纳米带形成机理,结果表明,中间产物PbSO4对表面活性剂是有制约性的,而当改变中间产物保持条件不变的情况下,模板效应失控,只能得到不规则的微晶体。 实验结果表明,制备硫化铅纳米带反应速度较为缓慢,易于控制,为制备不同形貌纳米带提供了一种有效方法。     

功能化PbS量子点的水相合成及结构表征

在水溶液中以Pb(NO3)2和Na2S为原料,巯基乙酸为稳定剂,合成了水溶性PbS量子点.用透射电子显微镜、扫描电子显微镜、粒度分析仪和红外光谱对PbS量子点进行了表征,结果表明所合成的PbS量子点的平均粒径为25 nm左右,分散性好,且巯基乙酸成功修饰于PbS纳米粒子表面,使其具有进一步与生物分子偶联的作用.     

Characterization of h-WO3 nanorods synthesized by hydrothermal process

Hexagonal tungsten oxide nanorods have been synthesized by hydrothermal strategy using Na₂WO₄·2H₂O as tungsten source, aniline and sulfate sodium as structure-directing templates. Techniques X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy have been used to characterize the structure, morphology and composition of the nanorods. The h-WO₃ nanorods are up to 5 μm in length, and 50–70 nm in diameter.     

Fabrication of hollow silica microspheres utilizing a hydrothermal approach

Hollow silica microspheres(HSMSs) have been successfully fabricated via a facile hydrothermal route using D-glucose as the sacrificial template and sodium silicate powder as the silica precursor.The resulting silica hollow particles were characterized by scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),and infrared spectroscopy(IR).The surface area was determined using the BET method.SEM and TEM images exhibited micro-sized silica hollow particles with a size of ~1.5μm.     

A highly regular hexapod structure of lead sulfide: solution synthesis and Raman spectroscopy

A highly regular hexapod-like structure of PbS with six symmetric arms has been synthesized by a simple and mild chemical solution route. The hexapod-like PbS structure was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-resolution TEM (HRTEM). The results show that each arm is perpendicular to the other four, and opposite to the last one. The arms are about 0.3-0.6 microm long, which have about 40-60 nm tips and 150-200 nm base. And the arm shows an icicle-like structure and some clear steps, and grows along 100 directions. The most possible growth mechanism discussed herein is based on the characterization results. The Raman spectra of the hexapod-like PbS structure were investigated. The results show that our products are sensitive to the laser and can be photodegraded easily.     

Fabrication of polystyrene–PbS core-shell and hollow PbS microspheres with sulfonated polystyrene templates

Uniform inorganic- (PbS) coated polymer core-shell and hollow PbS microspheres were prepared by an easy and economical approach. Monodisperse polystyrene (PS) microspheres were used as templates, as well as the core of the composite spheres; lead sulfide shells were obtained through the reaction of lead acetate (Pb(CH₃COO)₂) and thioacetamide (TAA) at room temperature. The morphologies and structures of the as-synthesized products were systematically characterized by transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), X-ray powder diffraction (XRD), and Fourier transform infrared spectra (FTIR). The fluorescence property of the as-synthesized product was also investigated. A reasonable mechanism for the formation of PS–PbS core-shell and hollow PbS microspheres was discussed. According to a series of parallel experiments, effects of related experimental parameters were also carefully investigated, such as the molar ratio of Pb(CH₃COO)₂ to TAA, reaction temperature, etc.     

Facile fabrication of long alpha-Fe(2)O(3), alpha-Fe and gamma-Fe(2)O(3) hollow fibers using sol-gel combined co-electrospinning technology

Long alpha-Fe(2)O(3) hollow fibers have been prepared through a facile sol-gel combined co-electrospinning technique using ferric citrate as precursor, and alpha-Fe and gamma-Fe(2)O(3) hollow fibers have been obtained by reduction and reoxidation at different conditions. The outer diameter of the as-prepared hollow fibers is 0.5-5 microm with wall thickness of 200-800 nm. The obtained tubular fibers were characterized by thermal gravimetric (TG), FT-IR spectra, X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and Raman techniques. In addition, magnetic properties of alpha-Fe and gamma-Fe(2)O(3) hollow fibers have also been investigated.     

MgSO4·5Mg(OH)2·3H2O的水热合成及反应时间对其形貌的影响

Both whisker and nanometer MgSO₄·5Mg(OH)₂·3H₂O(MOS) were prepared by hydrothermal method at 140℃ for different times， using NaOH and MgSO₄·7H₂O as raw materials. The MgSO₄·5Mg(OH)₂·3H₂O part- icles were characterized by powder X-ray diffraction(XRD)，thermal analysis(TGA-DSC)， infrared spectroscopy(FT-IR)，transmission electron microscopy(SEM) and scanning electron microscopy(TEM). The size distribution in whisker-like and nanocrystalline materials are in the range of 10～50μm and 10～20nm respectively. The whisker MOS is metastable phase in MgSO₄-NaOH-H₂O system at 140℃，whereas nanometer MOS is stable phase.