微波消解-电感耦合等离子体质谱法测定车用催化剂中铂、钯、铑

提出了电感耦合等离子体质谱法同时测定车用催化剂中铂、钯和铑的含量。样品0.100 0g经盐酸6mL、硝酸3mL、氢氟酸1mL和水4mL消解,选择195Pt、105Pd和103 Rh为待测同位素。铂、钯和铑的检出限(3σ)分别为0.003,0.5,0.002μg·L-1。方法用于5种催化剂样品的分析,测定结果与另两家实验室测定结果相一致。铂、钯和铑的回收率在85.5%～101%之间。     

碱熔-碲共沉淀分离-电感耦合等离子体原子发射光谱(ICP-AES)法测定废弃环保催化剂中铂钯铑

准确测定废弃环保催化剂中铂、钯、铑含量,是实现废弃环保催化剂贵金属高效回收和处置的重要保障技术条件之一,对回收铂族金属、湿法冶金生产物料平衡考察、保证买卖双方公平、公正交易等都具有重要的意义。采用碱熔分解废弃环保催化剂样品,碲共沉淀富集铂、钯、铑并与共存离子分离,采用电感耦合等离子体原子发射光谱法（ICP-AES）测定铂、钯、铑含量。结果表明,在1.2~2.7 mol/L盐酸体系中,加入碲沉淀剂,以二氯化锡为还原剂,能完全沉淀富集铂、钯、铑。铂、钯、铑校准曲线的线性范围为0.50～50.00 μg/mL,线性相关系数分别为0.99998、0.99996、0.99997;铂、钯、铑的检出限分别为2.6 μg/g、0.9 μg/g、1.2 μg/g;方法中铂、钯、铑的测定范围为25～25000 μg/g。按照实验方法测定废弃环保催化剂中铂、钯、铑,结果相对标准偏差(RSD,n=11)为0.2%～3.6%;加标回收率为96%～109%     

高效液相色谱法测定汽车尾气催化剂中铂、钯和铑的研究

研究了用 2 羟基萘 1 亚甲基若丹宁(HNPRN) 为柱前衍生试剂,以 Zorbax StableBound (4.6 mm×50 mm, 1.8μm) 快速分离柱为固定相,62%的甲醇(内含0.5%的乙酸)为流动相,高效液相色谱分离,二极管矩阵检测器检测测定铂、钯和铑的方法,三种贵金属元素的络合物在2.0 min内可达到基线分离。根据信噪比(S/N=3)得各金属离子的检出限分别为:铂 1.0μg·L-1,钯0.6μg·L-1,铑0.8μg·L-1,方法用于汽车尾气催化剂中痕量铂、钯和铑的测定,相对标准偏差在1.4%~1.6%之间,结果满意。     

石墨炉原子吸收光谱法测定矿石中铂、钯、铑、铱

矿石样品铂、钯、铑和铱经铅试金富集,所得金属合粒用硝酸-盐酸溶解,用石墨炉原子吸收光谱法测定矿石样品中铂、钯、铑和铱的含量。在优化的石墨炉工作条件下测得:铂的质量浓度在20～150μg.L-1、钯在15～120μg.L-1、铑和铱在6～100μg.L-1范围内与其吸光度呈线性关系,检出限(3s/k)依次为4.6,4.0,1.5,1.5μg.L-1。方法用于分析了2种矿石国家标准物质(GBW 07341、GBW 07342),测定结果与认定值相符。方法的回收率在87.6%～105.5%之间。测定值的日内和日间相对标准偏差(n=7)分别在2.8%～3.6%和3.5%～4.7%之间。     

泡沫塑料对贵金属-碘化亚锡-络合物的吸附分离行为研究

本文通过泡沫塑料对贵金属-碘化亚锡络合体系富集分离的条件、性能和机理的研究,建立了一种泡沫塑料同时富集分离微量铂、钯、锗、铱、金的新体系.实验结果表明,在1.0mol/L HCl、0.6mol/L KI和0.01mol/L SnCl_2的溶液中,振荡吸附30min.各元素分配系数均在10~5以上,吸附容量(mmol/g)分别为:铂0.25、钯0.24、铑0.12、铱0.10、金0.52,回收率分别为:铂99.2％、钯98.6％、铑97.8％、铱98.0％、金97.8％.试样中贵金属采用ICP-AES、FAAS测定,该方法用于砂铂矿、废催化剂、铜阳极泥等物料中铂、钯、铑、铱、金的测定,测定结果与其它方法对照相符。本文还进行了吸附动力学研究和富集物的红外光谱分析。     

丙醇-硫酸铵-水液-液体系萃取分离铂、钯、铑和金

研究了丙醇－（NH4）2SO4－水液－液体系对铂（Ⅱ）,钯（Ⅱ）,铑（Ⅲ）和金（Ⅲ）氯化亚锡络阴离子的萃取行为及体系在盐酸介质中的分相条件。实验表明在盐酸介质中体系可同时萃取铂（Ⅱ＿,钯（Ⅱ）,铑（Ⅲ）和金（Ⅲ）,对铂,钯,铑 和金的萃取率分别为99．4％,99．0％,98．3％和99．8％,方法可用于从贱金属中分离铂,钯,铑,金,对阳极泥,砂铂矿,废催化剂样品的分离分析结果与其它方法相符。     

碱熔-碲共沉淀分离-ICP-OES法测定脱氧催化剂中的铂钯含量

采用碱熔-碲共沉淀分离富集、电感耦合等离子体发射光谱(ICP-OES)法测定脱氧催化剂中铂、钯的含量。研究了碱熔和碲共沉淀富集分离的条件,并确定了ICP-OES法测定铂、钯的条件。结果表明,过氧化钠熔解-碲共沉淀法能够充分分离富集样品中的铂、钯,方法的检出限分别为4.6μg/L,7.2μg/L;相对标准偏差分别为1.3%,1.5%;加标回收率分别为98.2%~101%,97.6~101%。方法简单可靠,完全满足样品中铂、钯含量分析的要求,已经应用于生产样品的分析。     

高效液相色谱与石墨炉原子吸收光谱联用技术测定锗、铂、金

本文报道铑、铂、金的高效液相色谱与石墨炉原子吸收光谱联用技术研究。进行了反相离子对高效液相色谱分离铑、铂、金的条件实验。考察了离子对试剂及其浓度、甲醇-水比例、流动相酸度对铑、铂、金色谱行为的影响。得到三个贵金属元素的满意分离。讨论了液相色谱流出液引进石墨炉用原子吸收峰高法进行定量测定的方法。校正曲线的线性良好,对ppb级贵金属测定,得到满意结果。铑、铂、金的检出限分别为3.9×10~(-10)g,2.3×10~(-9)g和3.6×10~(-9)g。方法用于贵金属样品分析,相对标准偏差在1.8％—6.2％范围内。     

阳离子交换树脂分离-偏最小二乘光度法测定地质样品中的金、铂、钯、铑

本文采用阳离子交换树脂分离地质样品中的贱金属元素，利用偏最小二乘回归光度法在Mn＋－SnCl2－丁基罗丹明B－阿拉伯胶－乳化剂OP高灵敏的离子缔合物体系中对金、铂、钯、铑同时进行测定。结果表明，该方法灵敏度高，操作简便，可同时测定地质样品中痕量贵金属元素金、铂、钯、铑，其标准回入回收率为92．4％～107％。     

铂、钯负载型活性催化剂的制备及其对一氧化碳的催化氧化活性

用浸渍法分别将铂、钯负载在铝柱撑蒙脱石载体上,制备了铂、钯负载铝柱撑蒙脱石催化剂。运用X射线衍射(XRD)、原子吸收光谱(AAS)、透射电镜(TEM)等分析方法对样品的性能和结构进行了表征,并考察了不同铂、钯负载量的催化剂对一氧化碳的催化氧化性能。结果表明,铂、钯均以高度分散的纳米粒子状态均匀分布在载体表面,并表现出良好的CO催化氧化活性。铂、钯在铝柱撑蒙脱石载体表面的有效负载率在70%~76%之间,在相同的设计负载量条件下,铂的实际负载量和有效负载率均略大于钯。CO催化氧化试验结果表明,相对于负载前,负载后催化剂的催化活性明显增加,且其催化活性随着铂、钯负载量的增加而不断增强。在相同温度和负载量条件下,钯负载型催化剂的催化活性明显高于铂负载型催化剂。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.