利用［Fe/Pt］n多层膜降低L10-FePt有序化温度

采用直流磁控溅射方法制备了Fe/Pt多层膜和FePt单层薄膜，再经不同温度真空热处理得到 了有序相L10₀-FePt薄膜.通过x射线衍射谱和磁性研究表明，FePt单层薄膜需 要在500℃ 以上热处理，才能开始有序化转变，而Fe/Pt多层膜可以降低FePt薄膜有序化温度.［Fe(1 5nm)/Pt(15nm)］13₁₃薄膜在350℃热处理后，有序度已经增加到 06，相应矫 顽力达到了501kA/m.多层膜化促进有序化在较低的温度下进行，这是由于热处理过程中多 关键词： 0-FePt有序相')" href="#">L10₀-FePt有序相 磁控溅射 有序度 Fe/Pt多层膜     

室温生长MgO底层诱导(001)取向FePt薄膜的有序化过程对FePt成分的依赖

室温下通过磁控溅射在表面热氧化的Si基片上生长了MgO/Fe_xPt_100-x双层膜和Fe_xPt_100-x单层膜系列样品，Fe_xPt_100-x的原子成分x=48—68.研究了热处理前后不同成分FePt薄膜的晶体结构和磁性的变化，尤其是MgO底层的引入对FePt的晶体结构和磁性的影响 关键词： FePt(001)薄膜 0相')" href="#">L1₀相     

垂直取向FePt/Ag纳米颗粒薄膜的结构和磁性

用磁控溅射法在单晶MgO(100)基片上制备了［FePt 2 nm/Ag dnm］₁₀多层膜， 经真空热处理后，得到具有高矫顽力的垂直取向L1₀-FePt/Ag颗粒膜.x射线衍射结 果表明，在250 ℃的热基片上溅射，当Ag层厚度d=3—11 nm时，FePt颗粒具有很好的［001］取向，随着Ag层厚度的增加，FePt颗粒尺寸减小.［FePt 2 nm/Ag 9 nm］₁₀经过6 00 ℃真空热处理15 min后，颗粒大小仅约8 nm，垂直矫顽力达到692 kA/m.这种无磁耦合作用的颗粒膜，适合用作超高密度的垂直磁记录介质. 关键词： 磁控溅射 垂直磁记录 纳米颗粒膜 0-FePt/Ag')" href="#">L1₀-FePt/Ag     

Field dependence of spin and orbital moments of Fe in L10 FePt magnetic thin films

The field dependence of spin and orbital magnetic moments of Fe in L1₀ FePt magnetic thin films was investigated using X-ray magnetic circular dichroism (XMCD). The spin and orbital moments were calculated using the sum rules; it was found that the spin and orbital moment of Fe in L1₀ FePt films are ∼2.5 and 0.2 μ_B, respectively. The relative XMCD asymmetry at Fe L₃ peak on the dependence of applied field suggested that the majority magnetic moment of L1₀ FePt films resulted from Fe.     

Novel fabrication of net-like and flake-like Fe doped TiO2 thin films

New morphologies of net-like and flake-like TiO₂ thin films with different concentrations of Fe dopant were successfully fabricated by micro-arc oxidation (MAO) process of Ti plates and a subsequent chemical treatment of the as-prepared MAO-TiO₂ thin films. It was found that Fe ions can be easily introduced into the MAO-TiO₂ samples with the increase concentration of K₄(FeCN)₆·3H₂O precursor, and the amount of Fe determined the morphologies of TiO₂ thin films after chemical treatment; net-like morphology was observed with low Fe dopant, while it transformed to a flake-like one when Fe exceeds 1.7 at.%. UV-vis spectroscopy test showed that the absorption edge of the Fe ions doped TiO₂ thin films with new morphologies has an obvious red shift.     

利用FePt/Au多层膜结构制备垂直磁记录L10-FePt薄膜

利用磁控溅射方法在100℃的MgO单晶基片上制备了［FePt/Au］₁₀多层膜,并研究了采用FePt/Au多层膜结构对FePt薄膜的有序化温度、矫顽力（H_C）、垂直磁各向异性、晶粒尺寸以及颗粒间磁交换耦合作用的影响.磁性测试结果表明：FePt/Au多层膜在退火后具有较高的H_C、良好的垂直磁各向异性、较小的晶粒尺寸且无磁交换耦合作用.截面高分辨电镜分析表明：Au可以缓解MgO和FePt之间较大的晶格错配,从而促进薄 关键词： 0-FePt薄膜')" href="#">L1₀-FePt薄膜 有序化温度 垂直磁各向异性 磁交换耦合作用     

Thickness dependence of microstructure and magnetic properties in FePt/B<Subscript>4</Subscript>C multilayer thin films

FePt/B₄C multilayer films with different single FePt layer thickness were prepared by magnetron sputtering and subsequently annealing in vacuum. Influence of single FePt layer thickness on microstructure and magnetic property of FePt/B₄C films is investigated. Experimental results suggest that the Fe and Pt rich regions will appear in the interior of single FePt layer. The increasing of FePt layer thickness leads to the increase of grain size and volume fraction of order phase f ₀, which eventually induce satisfied coercivity (5.8 kOe).     

Influence of the phenomena occurring at the interface between L1<Subscript>0</Subscript>-ordered-FePt and Fe on the coercivity behavior

L1₀-ordered FePt/Fe thin bi-layers were grown using a molecular beam epitaxy onto (100)-MgO substrates changing the soft Fe layer thickness. The study of the intermixing phenomena occurring at the hard/soft interfaces was carried out using surface Mössbauer spectroscopy. The magnetic properties of the samples were analyzed with a magneto-optical Kerr effect magnetometer. The surface morphology and the magnetic domains were analyzed with an UHV atomic and magnetic force microscopy in tapping and lift mode respectively.The present work clearly demonstrates that the degree of interface intermixing and reactions is the responsible for the coercivity behavior in exchange-spring magnets.     

Preparation of Fe/Pt Films with Perpendicular Magnetic Anisotropy

We have investigated the microstructures and magnetic properties of L1₀ ordered equi-atomic FePt thin films prepared by ion beam sputtering and subsequent annealing. It is observed from X-ray reflectivity and X-ray diffraction measurements that the mixing at Fe/Pt interfaces starts to occur with annealing and leading to the FePt alloy phase formation. The rapid increase in the coercivity values above 275°C, obtained from vibrating sample magnetometer (VSM) measurements, confirms the formation of the ordered L1₀ FCT FePt phase.     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术,分别沉积Ti和Ti/Al膜,经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序,分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27 关键词： 2薄膜')" href="#">多孔TiO₂薄膜 阳极氧化 紫外光吸收     

Cu掺杂对FexPt1－x薄膜有序化的影响

利用磁控溅射制备了薄膜厚度为50nm的系列(Fe_xPt_1-x)_100-yCu_y(x=0.46—0.56,y=0,0.04,0.12) 样品.利用直流共溅射方法精确控制Fe和Pt的原子比.实验结果表明，当x>0.52时，样品中添加Cu不能促进FePt的有序化，但是对于FePt化学原子定比或富Pt的样品，添加Cu可以促进FePt有序化，而且随着Fe含量的减少，需要更多的Cu添加才能实现较低温度下FePt薄膜的有序化.实验结果表明，原子比(FeCu)/Pt达到1.1—1.2的范围时，即可实现较低温度的有序化. 关键词： 0-FePt有序相')" href="#">L1₀-FePt有序相 磁控溅射 有序度 Cu掺杂     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术，利用LSCO/CeO₂/YSZ多异质缓冲层，在Si(100)基 片上成功地制备了c轴一致取向的Bi_3.15Nd_0.85Ti₃O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构 、取向和形貌特征，考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响，确定 了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型 的蝴蝶形曲线，表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与 薄膜取向的相关性. 关键词： 3.15Nd_0.85Ti₃O₁₂')" href="#">Bi_3.15Nd_0.85Ti₃O₁₂ 铁电薄 膜 多层异质结 脉冲激光沉积     

Structural and magnetic properties of RF sputtered FePt/Fe multilayers

Series of [FePt(4min)/Fe(t_Fe)]₁₀ multilayers have been prepared by RF magnetron sputtering and post-annealing in order to optimize their magnetic properties by structural designs. The structure, surface morphology, composition and magnetic properties of the deposited films have been characterized by X-ray diffractometer (XRD), Rutherford backscattering (RBS), scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX) and vibrating sample magnetometer (VSM). It is found that after annealing at temperatures above 500 °C, FePt phase undergoes a phase transition from disordered FCC to ordered FCT structure, and becomes a hard magnetic phase. X-ray diffraction studies on the series of [FePt/Fe]_n multilayer with varying Fe layer thickness annealed at 500 and 600 °C show that lattice constants change with Fe layer thickness and annealing temperature. Both lattice constants a and c are smaller than those of standard ones, and lattice constant a decreases as Fe layer deposition time increases. Only a slight increase in grain size was observed as Fe layer decreased in samples annealed at 500 °C. However, the increase in grain size is large in samples annealed at 600 °C. The coercivities of [FePt/Fe]_n multilayers decrease with Fe layer deposition time, and the energy product (BH)_max reaches a maximum in the samples with Fe layer deposition time of 3 min. Comparison of magnetic properties with structure showed an almost linear relationship between the lattice constant a and the coercivities of the FePt phase.     

Control of crystallographic orientation in L10 FePt films by using Cr and CrW underlayers

The microstructure and magnetic properties of FePt films grown on Cr and CrW underlayers were investigated. The FePt films that deposited on Cr underlayer show (2 0 0) orientation and low coercivity because of the diffusion between FePt and Cr underlayer. The misfit between FePt magnetic layer and underlayer increases by small addition of W element in Cr underlayer or using a thin Mo intermediate layer, which is favorable for the formation of (0 0 1) orientation and the transformation of FePt from fcc to fct phase. A good FePt (0 0 1) texture was obtained in the films with Cr₈₅W₁₅ underlayer with substrate temperature of 400 °C. The FePt films deposited on Mo/Cr underlayer exhibit larger coercivity than that of the films grown on Pt/Cr₈₅W₁₅ because 5 nm Mo intermediate layer depressed the diffusion of Cr into magnetic layer.     

Microstructure and electrical properties of Ba0.5Sr0.5TiO3 thin films prepared on copper foils with La2O3 buffer layers

Ba_0.5Sr_0.5TiO₃ (BST) thin films were deposited on copper foils via sol-gel method with La₂O₃ as a buffer layer. The films were processed in almost inert atmosphere so that the substrate oxidation was avoided while allowing the perovskite film phase to crystallize. The existence of a La₂O₃ buffer layer between the BST thin film and Cu foil improved the dielectric constant and reduced the leakage current density of the BST thin film. Meanwhile, the BST thin film exhibited ferroelectric character at room temperature, which was contrast to the para-electric behavior of the film without the buffer layer. Effects of La₂O₃ buffer layer on the crystallizability and microstructure of BST thin films were also investigated.     

The microwave response of MgB2 /Al2O3 superconducting thin films

Microwave characteristics of MgB2/Al2O3 superconducting thin films were investigated by coplanar resonator technique. The thin films studied have different grain sizes resulting from different growth techniques. The experimental results can be described very well by a grain-size model which combines coplanar resonator theory and Josephson junction network model. It was found that the penetration depth and surface resistance of thin films with smaller grain sizes are larger than those of thin films with larger grain sizes.     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

Effect of interfacial diffusion on microstructure and properties of FePt/B4C multifunctional multilayer composite films

FePt/B₄C multilayer composite films were prepared by magnetron sputtering and subsequent annealing in vacuum. By changing Fe layer thickness of [Fe/Pt]₆/B₄C films, optimal magnetic property (8.8 kOe and remanence squareness is about 1.0) is got in [Fe(5.25 nm)/Pt(3.75 nm)]₆/B₄C sample whose composition is Fe rich and near stoichiometric ratio. The characterizations of microstructure demonstrate that the diffusion of B and C atoms into FePt layer depends strongly on B₄C interlayer thickness. When B₄C interlayer thickness of [Fe(2.625 nm)/Pt(3.75 nm)/Fe(2.625 nm)/B₄C]₆ films is bigger than 3 nm, stable value of grain size (6-6.5 nm), coercivity (6-7 kOe) and hardness (16-20 GPa) is observed. Finally, the multifunctional single FePt/B₄C composite film may find its way to substitute traditional three-layer structure commonly used in present data storage technology.     

Microstructures and multiferroic properties of textured Bi0.8La0.2FeO3 thin films

La-substituted BiFeO₃, Bi_0.8La_0.2FeO₃, thin films were fabricated on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and high-resolution transmission electron microscope were used to analyze the structures of the films. The results show the films fabricated under optimized growth condition are (0 1 2) textured. X-ray photoemission spectroscopy results indicate that the oxidation state of Fe ion is Fe³⁺ in the films without detectable Fe²⁺. The films show low leakage current and excellent dielectric characters. Multiferroic properties with a remnant ferroelectric polarization of 5.2 μC/cm² and a remanent magnetization of 0.02 μ_B/Fe were established. These results have some implications for further research.