Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

Properties of Si-doped GaN and AlGaN/GaN heterostructures grown by RF-MBE on high resistivity Fe-doped GaN

Silicon-doped GaN epilayers and AlGaN/GaN heterostructures were developed by nitrogen plasma-assisted molecular beam epitaxy on high resistivity iron-doped GaN (0001) templates and their properties were investigated by atomic force microscopy, x-ray diffraction and Hall effect measurements. In the case of high electron mobility transistors heterostructures, the AlN mole fraction and the thickness of the AlGaN barrier employed were in the range of from 0.17 to 0.36 and from 7.5 to 30 nm, respectively. All structures were capped with a 2 nm GaN layer.Despite the absence of Ga droplets formation on the surface, growth of both GaN and AlGaN by RF-MBE on the GaN (0001) surfaces followed a step-flow growth mode resulting in low surface roughness and very abrupt heterointerfaces, as revealed by XRD. Reciprocal space maps around the reciprocal space point reveal that the AlGaN barriers are fully coherent with the GaN layer.GaN layers, n-doped with silicon in the range from 10¹⁵ to 10¹⁹ cm⁻³ exhibited state of the art electrical properties, consistent with a low unintentional background doping level and low compensation ratio. The carrier concentration versus silicon cell temperatures followed an Arhenius behaviour in the whole investigated doping range. The degenerate 2DEG, at the AlGaN/GaN heteroiterfaces, exhibited high Hall mobilities reaching 1860 cm²/V s at 300 K and 10 220 cm²/V s at 77 K for a sheet carrier density of 9.6E12 cm⁻².The two dimensional degenerate electron gas concentration in the GaN capped AlGaN/GaN structures was also calculated by self-consistent solving the Schrödinger–Poisson equations. Comparison with the experimental measured values reveals a Fermi level pinning of the GaN (0001) surface at about 0.8 eV below the GaN conduction band.     

High-quality two-dimensional electron gas at large scale GaN/AlGaN wafer interface prepared by mass production MOCVD systems

Basic electronic properties of two-dimensional electron gas (2DEG) formed at GaN/AlGaN hetero-interface in large-scale (100 mm) wafer made by metal organic chemical vapour deposition (MOCVD) have been reported and discussed. From conventional Hall measurements, highest electron mobility was found to be μ_e∼1680 and 9000 cm²/V s at room temperature and at ∼5 K, respectively, for sheet electron density of n_s∼8×10¹² cm⁻². In magneto-resistance (MR) measurements carried out at 1.5 K in Hall bar sample defined by photolithography and ion implantation, very clear Schubnikov de-Haas oscillations and integer quantum Hall effect were observed in diagonal (R_xx) and off-diagonal (R_xy) resistances, respectively. In addition, a good insulating nature of GaN layer is confirmed by capacitance-voltage (C-V) measurement. These results suggest the high-qualitiness of our 100 mm GaN/AlGaN high electron mobility transistor (HEMT) wafers comparable to those so far reported.     

Influence of AlN interfacial layer on electrical properties of high-Al-content Al0.45Ga0.55N/GaN HEMT structure

Unintentionally doped high-Al-content Al_0.45Ga_0.55N/GaN high electron mobility transistor (HEMT) structures with and without AlN interfacial layer were grown by metal-organic chemical vapor deposition (MOCVD) on two-inch sapphire substrates. The effects of AlN interfacial layer on the electrical properties were investigated. At 300 K, high two-dimensional electron gas (2DEG) density of 1.66 × 10¹³ cm⁻² and high electron mobility of 1346 cm² V⁻¹ s⁻¹ were obtained for the high Al content HEMT structure with a 1 nm AlN interfacial layer, consistent with the low average sheet resistance of 287 Ω/sq. The comparison of HEMT wafers with and without AlN interfacial layer shows that high Al content AlGaN/AlN/GaN heterostructures are potential in improving the electrical properties of HEMT structures and the device performances.     

High-quality InAlN/GaN heterostructures grown by metal–organic vapor phase epitaxy

We fabricated high-quality InAlN/GaN heterostructures by metal–organic vapor phase epitaxy (MOVPE). X-ray diffraction measurements revealed that InAlN/GaN heterostructures grown under optimal conditions have flat surfaces and abrupt heterointerfaces. Electron mobility from 1200 to 2000 cm²/V s was obtained at room temperature. To our knowledge, this mobility is the highest ever reported for InAlN/GaN heterostructures. We also investigated the relationship between the Al composition and sheet electron density (N_s) for the first time. N_s increased from 1.0×10¹² to 2.7×10¹³ cm⁻² when the Al composition increased from 0.78 to 0.89.     

Significant performance enhancement in AlGaN/GaN high electron mobility transistor by high-κ organic dielectric

The electrical properties of AlGaN/GaN high electron mobility transistor (HEMT) with and without high-κ organic dielectrics are investigated. The maximum drain current I_{D max} and the maximum transconductance g_{m max} of the organic dielectric/AlGaN/GaN structure can be enhanced by 74.5%, and 73.7% compared with those of the bare AlGaN/GaN HEMT, respectively. Both the threshold voltage V_T and g_{m max} of the dielectric/AlGaN/GaN HEMT are strongly dielectric-constant-dependent. Our results suggest that it is promising to significantly improve the performance of the AlGaN/GaN HEMT by introducing the high-κ organic dielectric.     

Degraded model of radiation-induced acceptor defects for GaN-based high electron mobility transistors （HEMTs）

Using depletion approximation theory and introducing acceptor defects which can characterize radiation induced deep-level defects in AlGaN/GaN heterostructures, we set up a radiation damage model of AlGaN/GaN high electron mobility transistor (HEMT) to separately simulate the effects of several main radiation damage mechanisms and the complete radiation damage effect simultaneously considering the degradation in mobility. Our calculated results, consistent with the experimental results, indicate that thin AlGaN barrier layer, high Al content and high doping concentration are favourable for restraining the shifts of threshold voltage in the AlGaN/GaN HEMT; when the acceptor concentration induced is less than 10¹⁴cm^-3, the shifts in threshold voltage are not obvious; only when the acceptor concentration induced is higher than 10¹⁶cm^-3, will the shifts of threshold voltage remarkably increase; the increase of threshold voltage, resulting from radiation induced acceptor, mainly contributes to the degradation in drain saturation current of the current--voltage (I--V) characteristic, but has no effect on the transconductance in the saturation area.     

High vertical breakdown strength in with low specific on‐resistance AlGaN/AlN/GaN HEMTs on silicon

Off‐state and vertical breakdown characteristics of AlGaN/AlN/GaN high‐electron‐mobility transistors (HEMTs) on high‐resistivity (HR)‐Si substrate were investigated and analysed. Three‐terminal off‐state breakdown (BV_gd) was measured as a function of gate–drain spacing (L_gd). The saturation of BV_gd with L_gd is because of increased gate leakage current. HEMTs with L_gd = 6 µm exhibited a specific on‐resistance R_DS[ON] of 0.45 mΩ cm². The figure of merit (FOM = BV_gd²/R_DS[ON]) is as high as 2.0 × 10⁸ V² Ω^–1 cm^–2, the highest among the reported values for GaN HEMTs on Si substrate. A vertical breakdown of ～1000 V was observed on 1.2 µm thick buffer GaN/AlN grown on Si substrate. The occurrence of high breakdown voltage is due to the high quality of GaN/AlN buffer layers on Si substrate with reduced threading dislocations which has been confirmed by transmission electron microscopy (TEM). This indicates that the AlGaN/AlN/GaN HEMT with 1.2 µm thick GaN/AlN buffer on Si substrate is promising candidate for high‐power and high‐speed switching device applications. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Correlation between morphological, electrical and optical properties of GaN at all stages of MOVPE Si/N treatment growth

GaN has been grown using Si/N treatment growth by MOVPE on sapphire (0001) in a home-made vertical reactor. The growth was monitored by in situ laser reflectometry. The morphological, electrical and optical properties of GaN are investigated at all the growth stages. To this aim, the growth was interrupted at different stages. The obtained samples are ex situ characterized by scanning electron microscopy (SEM), room temperature Van der Pauw–Hall electrical transport and low temperature (13 K) photoluminescence (PL) measurements. The SEM images show clearly the coalescence process. A smooth surface is obtained for a fully coalesced layer. During the coalescence process, the electron concentration (n) and mobility (μ) vary from 2×10¹⁹ cm⁻³ to 2×10¹⁷ cm⁻³ and 12 cm²/V s–440 cm²/V s, respectively. The PL maxima shift to higher energy and the FWHM decreases to about 4 meV. A correlation between PL spectra and Hall effect measurements is made. We show that the FWHM follows a n^2/3 power law for n above 10¹⁸ cm⁻³.     

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10¹⁵ cm^-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas (2DEG) decreased after neutron irradiation. There was no evidence of the full-width at half-maximum of X-ray diffraction (XRD) rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

MBE growth of nitride-based photovoltaic intersubband detectors

In this work, we present the plasma-assisted molecular-beam epitaxial growth of quantum well infrared photodetector (QWIP) structures, including the Si-doped GaN/AlN short-period superlattice of the active region, conductive AlGaN claddings and integration of the final device. The growth of Si-doped GaN/AlN multiple quantum well (QW) structures is optimized by controlling substrate temperature, metal excess and growth interruptions. Structural characterization confirms a reduction of the interface roughness to the monolayer scale. P-polarized intersubband absorption peaks covering the 1.33–1.91 μm wavelength range are measured on samples with QW thickness varying from 1 to 2.5 nm. The absorption exhibits Lorentzian shape with a line width around 100 meV in QWs doped 5×10¹⁹ cm⁻³. To prevent partial depletion of the QWs owing to the internal electric field, we have developed highly-conductive Si-doped AlGaN cladding layers using In as a surfactant during growth. Complete ISB photodetectors with 40 periods of 1 nm-thick Si-doped GaN QWs with 2 nm-thick AlN barriers have been grown on conductive AlGaN claddings, the Al mole fraction of the cladding matching the average Al content of the active region. Temperature-dependent photovoltage measurements reveal a narrow (90 meV) detection peak at 1.39 μm.     

Growth and characterisation of GaN with reduced dislocation density

Two GaN MOVPE growth methods to reduce the threading dislocation (TD) density have been explored. The combined effects of (1) in situ SiN_x masking of the sapphire substrate and (2) starting the epitaxial growth at low V-to-III ratio on the GaN film quality were studied by atomic force microscopy, transmission electron microscopy and high-resolution X-ray diffraction. It was found that the annealing condition of the low-temperature nucleation layer after in situ SiN_x masking is critical in order to decrease the density of nucleation sites and hence increase the average grain size to about 5 μm. However, the coalescence of large grains with vertical side facets results in the formation of dense bundles of TDs at the grain boundaries combined with large numbers of basal-plane dislocation loops throughout the film. The formation of these dislocations can be prevented by starting the epilayer growth at low V-to-III ratio, resulting in the formation of grains with inclined side facets. The interaction of the TDs with the inclined side facets causes the dislocations to bend 90 as the grains grow in size and coalesce. GaN films with dislocation densities as low as 1×10⁸ cm⁻², giving full-width at half-maximum values of 180 and 220 arcsec for respectively (002) and (302) omega scans, were achieved by the combination of in situ masking and low V–III ratio epilayer growth. Hall carrier mobility values in excess of 900 cm² V ⁻¹ s⁻¹ were deduced for Si-doped layers.     

In-plane gate transistors in AlxGa1−xN/GaN heterostructures written by focused ion beams

Focused ion beam implantation of gallium and dysprosium was used to locally insulate the near-surface two-dimensional electron gas of Al_xGa_1−xN/GaN heterostructures. The threshold dose for insulation was determined to be 2×10¹⁰ cm⁻¹ for 90 keV Ga⁺ and 1×10⁹ cm⁻¹ for 200 keV Dy²⁺ at 4.2 K. This offers a tool not only for inter-device insulation but also for direct device fabrication. Making use of “open-T” like insulating line patterns, in-plane gate transistors have been fabricated by focused ion beam implantation. An exemplar with a geometrical channel width of 1.5 μm shows a conductance of 32 μS at 0 V gate voltage and a transconductance of around 4 μS, which is only slightly dependent on the gate voltage.     

High temperature electron transport properties of AlGaN/GaN heterostructures with different Al-contents

Electron transport properties in AlGaN/GaN heterostructures with different Al-contents have been investigated from room temperature up to 680 K. The temperature dependencies of electron mobility have been systematically measured for the samples. The electron mobility at 680 K were measured as 154 and 182 cm²/V·s for Al_0.15Ga_0.85N/GaN and Al_0.40Ga_0.60N/GaN heterostructures, respectively. It was found that the electron mobility of low Al-content Al_0.15Ga_0.85N/GaN heterostructure was less than that of high Al-content Al_0.40Ga_0.60N/GaN heterostructure at high temperature of 680 K, which is different from that at room temperature. Detailed analysis showed that electron occupations in the first subband were 75% and 82% at 700 K for Al_0.15Ga_0.85N/GaN and Al_0.40Ga_0.60N/GaN heterostructures, respectively, and the two dimensional gas (2DEG) ratios in the whole electron system were 30% and near 60%, respectively. That indicated the 2DEG was better confined in the well, and was still dominant in the whole electron system for higher Al-content AlGaN/GaN heterostructure at 700 K, while lower one was not. Thus it had a higher electron mobility. So a higher Al-content AlGaN/GaN heterostructure is more suitable for high-temperature applications.     

A quasi-two-dimensional charge transport model of AlGaN/GaN high electron mobility transistors (HEMTs)

A quasi-two-dimensional charge transport model of AlGaN/GaN high electron mobility transistor has been developed that is capable of accurately predicting the drain current as well as small-signal parameters such as drain conductance and device transconductance. This model built up with incorporation of fully and partially occupied sub-bands in the interface quantum well, combined with a numerically self-consistent solution of the Schrödinger and Poisson equations. In addition, nonlinear polarization effects, self-heating, voltage drops in the ungated regions of the device are also taken into account. Also, to develop the model, the accurate two-dimensional electron gas mobility and the electron drift velocity have been used. The calculated model results are in very good agreement with existing experimental data for Al_mGa_1−mN/GaN HEMT devices with Al mole fraction within the range from 0.15 to 0.50, especially in the linear regime of I–V curve.     

The effects of GaN capping layer thickness on two-dimensional electron mobility in GaN/AlGaN/GaN heterostructures

In this paper we present a study of the effect of GaN capping layer thickness on the two-dimensional (2D)-electron mobility and the two-dimensional electron gas (2DEG) sheet density which is formed near the AlGaN barrier/buffer GaN layer. This study is undertaken using a fully numerical calculation for GaN/Al_xGa_1−xN/GaN heterostructures with different Al mole fraction in the Al_xGa_1−xN barrier, and for various values of barrier layer thickness. The results of our analysis clearly indicate that increasing the GaN capping layer thickness leads to a decrease in the 2DEG density. Furthermore, it is found that the room-temperature 2D-electron mobility reaches a maximum value of approximately 1.8×10³ cm² /Vs⁻¹ for GaN capping layer thickness grater than 100 Å with an Al_0.32Ga_0.68N barrier layer of 200 Å thick. In contrast, for same structure, the 2DEG density decreases monotonically with GaN capping layer thickness, and eventually saturates at approximately 6×10¹² cm⁻² for capping layer thickness greater than 500 Å. A comparison between our calculated results with published experimental data is shown to be in good agreement for GaN capping layers up to 500 Å thickness.     

中子辐照对AlGaN/GaN高电子迁移率晶体管器件电特性的影响

本文采用能量为1 MeV的中子对SiN钝化的AlGaN/GaN HEMT(高电子迁移率晶体管)器件进行了最高注量为1015cm-2的辐照.实验发现:当注量小于1014cm-2时,器件特性退化很小,其中栅电流有轻微变化(正向栅电流IF增加,反向栅电流IR减小),随着中子注量上升,IR迅速降低.而当注量达到1015cm-2时,在膝点电压附近,器件跨导有所下降.此外,中子辐照后,器件欧姆接触的方块电阻退化很小,而肖特基特性退化却相对明显.通过分析发现辐照在SiN钝化层中引入的感生缺陷引起了膝点电压附近漏电流和反向栅泄漏电流的减小.以上结果也表明,SiN钝化可以有效地抑制中子辐照感生表面态电荷,从而屏蔽了绝大部分的中子辐照影响.这也证明SiN钝化的AlGaN/GaN HEMT器件很适合在太空等需要抗位移损伤的环境中应用.     

The structure of crystallographic damage in GaN formed during rare earth ion implantation with and without an ultrathin AlN capping layer

The crystallographic nature of the damage created in GaN implanted by rare earth ions at 300 keV and room temperature has been investigated by transmission electron microscopy versus the fluence, from 7×10¹³ to 2×10¹⁶ at/cm², using Er, Eu or Tm ions. The density of point defect clusters was seen to increase with the fluence. From about 3×10¹⁵ at/cm², a highly disordered ‘nanocrystalline layer’ (NL) appears on the GaN surface. Its structure exhibits a mixture of voids and misoriented nanocrystallites. Basal stacking faults (BSFs) of I₁, E and I₂ types have been noticed from the lowest fluence, they are I₁ in the majority. Their density increases and saturates when the NL is observed. Many prismatic stacking faults (PSFs) with Drum atomic configuration have been identified. The I₁ BSFs are shown to propagate easily through GaN by folding from basal to prismatic planes thanks to the PSFs.When implanting through a 10 nm AlN cap, the NL threshold goes up to about 3×10¹⁶ at/cm². The AlN cap plays a protective role against the dissociation of the GaN up to the highest fluences. The flat surface after implantation and the absence of SFs in the AlN cap indicate its high resistance to the damage formation.     

Energy and momentum relaxation of electrons in bulk and 2D GaN

We present our experimental and theoretical studies regarding the energy and momentum relaxation of hot electrons in n-type bulk GaN and AlGaN/GaN HEMT structures. We determine the non-equilibrium temperatures and the energy relaxation rates in the steady state using the mobility mapping technique together with the power balance conditions as described by us elsewhere [N. Balkan, M.C. Arikan, S. Gokden, V. Tilak, B. Schaff, R.J. Shealy, J. Phys.: Condens. Matter 14 (2002) 3457]. We obtain the e–LO phonon scattering time of 8 fs and show that the power loss of electrons due to optical phonon emission agrees with the theoretical prediction. The drift velocity–field curves at high electric fields indicate that the drift velocity saturates at approximately 3×10⁶ cm/s for the two-dimensional structure and 4×10⁶ cm/s for the bulk material at 77 K. These values are much lower than those predicted by the existing theories. A critical analysis of the observations is given with a model taking into account of the non-drifting non-equilibrium phonon production.     

GaN/AlN quantum dot photodetectors at 1.3–1.5 μm

We have demonstrated GaN/AlN quantum dots (QD) photodetectors, relying on intraband absorption and in-plane carrier transport in the wetting layer. The devices operate at room temperature in the wavelength range 1.3–1.5 μm. Samples with 20 periods of Si-doped GaN QD layers, separated by 3 nm-thick AlN barriers, have been grown by plasma-assisted molecular-beam epitaxy on an AlN buffer on a c-sapphire substrate. Self-organized dots are formed by the deposition of 5 monolayers of GaN under nitrogen-rich conditions. The dot height is 1.2±0.6 to 1.3±0.6 nm and the dot density is in the range 10¹¹–10¹² cm⁻². Two ohmic contacts were deposited on the sample surface and annealed in order to contact the buried QD layers. The dots exhibit TM polarized absorption linked to the s–p_z transition. The photocurrent at 300 K is slightly blue-shifted with respect to the s–p_z intraband absorption. The responsivity increases exponentially with temperature and reaches a record value of 10 mA/W at 300 K for detectors with interdigitated contacts.