Photoluminescence studies of Si nanocrystals

Summary We report room temperature time-resolved photoluminescence (PL) and temperature dependence of continuous wave (cw) PL studies of high fluence (from 3·10¹⁶ to 3·10¹⁷ cm⁻²) Si⁺-implanted thermal SiO₂ layers after annealing at high temperature (T=1000°C). Such measurements were related to TEM analysis of samples. Nancocrystals were observed at TEM only a samples implanted at higher fluence. In these samples a near infrared PL signal peaked at approximately 1.5 eV with decay time of about 100 μs is present. Besides, in all samples a light emission is present in the green region of the spectrum. The intensity of the emission shows large variations with ion fluence, and is characterized by 0.4, 2 and 7 ns decay times. Paper presented at the III INSEL (Incontro Nazionale sul Silicio Emettitore di Luce) Torino, 12–13 October 1995.     

Photoluminescence evolution in self-ion-implanted and annealed silicon

Si⁺ ion-implanted silicon wafers are annealed at different temperatures from room temperature to 950~℃ and then characterized by using the photoluminescence (PL) technique at different recorded temperatures (RETs). Plentiful optical features are observed and identified clearly in these PL curves. The PL spectra of these samples annealed in different temperature ranges are correspondingly dominated by different emission peaks. Several characteristic features, such as an R line, S bands, a W line, the phonon-assistant W^\rm TA and Si^\rm TO peaks, can be detected in the PL spectra of samples annealed at different temperatures. For the samples annealed at 800~\du, emission peaks from the dislocations bounded at the deep energy levels of the forbidden band, such as D_1 and D₂ bands, can be observed at a temperature as high as 280~K. These data strongly indicate that a severe transformation of defect structures could be manipulated by the annealing and recorded temperatures. The deactivation energies of the main optical features are extracted from the PL data at different temperatures.     

注入Ar+的蓝宝石晶体退火前后光致发光谱的分析

对注入Ar⁺后不同晶面取向的蓝宝石晶体在不同退火条件下的光致发光谱进行了分析.分析结果表明:三种晶面取向的蓝宝石样品经Ar⁺注入后,其光致发光谱中均出现了新的位于506nm处的发光峰;真空和空气气氛下的退火均对样品在506nm处的发光有增强作用,不同晶面取向的样品发光增强程度不同,且发光增强至最大时的退火温度也不同,空气气氛下的退火使样品发光增强程度更为显著.由此可以看出,退火气氛、退火温度和晶面取向均对样品发光峰强度有影响. 关键词： 2O₃')" href="#">Al₂O₃ 离子注入 退火 光致发光谱     

Temperature behaviour of optical properties of Si+-implanted SiO2

Silicon nanocrystals were prepared by Si⁺-ion implantation and subsequent annealing of SiO₂ films thermally grown on a c-Si wafer. Different implantation energies (20-150 keV) and doses - cm ^-2 ) were used in order to achieve flat implantation profiles (through the thickness of about 100 nm) with a peak concentration of Si atoms of 5, 7, 10 and 15 atomic%. The presence of Si nanocrystals was verified by transmission electron microscopy. The samples exhibit strong visible/IR photoluminescence (PL) with decay time of the order of tens of μs at room temperature. The changes of PL in the range 70-300 K can be well explained by the exciton singlet-triplet splitting model. We show that all PL characteristics (efficiency, dynamics, temperature dependence, excitation spectra) of our Si⁺-implanted SiO₂ films bear close resemblance to those of a light-emitting porous Si and therefore we suppose similar PL origin in both materials. Received 1st September 1998 and Received in final form 7 September 1999     

Time-resolved photoluminescence spectroscopy of InAs quantum dots on InP with various InAlGaAs barrier thicknesses

The Optical characteristics of InAs quantum dots (QDs) embeded in InAlGaAs on InP have been investigated by photoluminescence (PL) spectroscopy and time-resolved PL. Four different QD samples are grown by using molecular beam epitaxy, and all the QD samples have five-stacked InAs quantum dot layers with a different InAlGaAs barrier thickness. The PL yield from InAs QDs was increased with an increase in the thickness of the InAlGaAs barrier, and the emission peak positions of all InAs QD samples were measured around 1.5 μm at room temperature. The decay time of the carrier in InAs QDs is decreased abruptly in the QD sample with the 5 nm InAlGaAs barrier. This feature is explained by the tunneling and coupling effect in the vertical direction and probably defect generation.     

非晶氧化硅薄膜带尾发光特性

采用等离子体增强化学气相沉积技术,通过改变CO2流量制备了不同氧含量的非晶氧化硅薄膜。利用紫外可见吸收谱、傅里叶红外吸收谱和稳态/瞬态光致发光谱等技术研究了薄膜的微观结构和光学特性。实验结果表明,随着氧含量的增加,薄膜的带隙增大,光致发光强度增加、峰值朝高能方向移动、光谱半峰全宽展宽。时间分辨光谱显示薄膜发光峰值处的衰减时间随氧含量的增加从6.2ns单调增加到21ns,而同一样品的发光寿命随发射波长能量增加而减小。综合分析光学吸收、发射及发光衰减特性表明,薄膜的发光机制主要归结为非晶材料带尾态之间的辐射复合。     

非掺杂ZnO薄膜中紫外与绿色发光中心

用直流反应溅射方法在硅衬底上淀积了ZnO薄膜,测量它们的光致发光(PL)光谱,观察到两个发光峰,峰值能量分别为3.18(紫外峰,UV)和2.38eV(绿峰).样品用不同温度分别在氧气、氮气和空气中热处理后,测量了PL光谱中绿峰和紫外峰强度随热处理温度和气氛的变化,同时比较了用FP-LMT方法计算的ZnO中几种本征缺陷的能级位置.根据实验和能级计算的结果,推测出ZnO薄膜中的紫外峰与ZnO带边激子跃迁有关,而绿色发光主要来源于导带底到氧错位缺陷(O_Zn)能级的跃迁,而不是通常认为的氧空 关键词： ZnO薄膜 热处理 光致发光光谱 缺陷能级     

Thermal dissociation of excitons in a type-I GaAs/AlAs superlattice studied by time-resolved photoluminescence measurements

In order to investigate thermal properties of excitons, we have performed time-resolved photoluminescence (PL) measurements for a type-I (GaAs)₁₅/(AlAs)₁₅ superlattice. At low temperatures, PL signals show ordinal exponential time decay, whereas at high temperatures, the PL shows power decay. Such change of PL signals is understood by considering thermal dissociation of exciton into account. At low temperatures, recombination of bound excitons generates PL which shows exponential decay. At temperatures higher than the exciton binding energy, correlation between electrons and holes disappears. Recombination of free excitons causes PL which decays by a power function. By means of the least-squares fitting, we evaluate the portion of bound excitons, recombination time of bound and free excitons as functions of temperatures.     

Time-resolved luminescence spectroscopy of pure and doped with Ce3+ ions SrAlF5 crystals

The results of a study of time-resolved photoluminescence (PL) and energy transfer in both pure and doped with Ce³⁺ ions SrAlF₅ (SAF) single crystals are presented. The time-resolved and steady-state PL spectra in the energy range of 1.5–6.0 eV, the PL excitation spectra and the reflectivity in the energy range of 3.7–21 eV, as well as the PL decay kinetics were measured at 8.8 and 295 K. The lattice defects were revealed in the low temperature PL spectra (emission bands at 2.9 and 4.5 eV) in the undoped SAF crystals. The luminescence spectra of the doped Ce³⁺:SAF crystals demonstrate a new selective emission bands in the range of 3.7–4.5 eV with the exponential decay kinetics (τ ≈ 60 ns at X-ray excitation). These bands correspond to the d-f transitions in Ce³⁺ ions, which occupy nonequivalent sites in the crystal lattice.     

Temperature‐dependent emission shift and carrier dynamics in deep ultraviolet AlGaN/AlGaN quantum wells

Radiative and nonradiative processes in deep ultraviolet (DUV) AlGaN/AlGaN multiple quantum wells (MQWs) grown by LP‐MOCVD have been studied by means of deep ultraviolet time‐integrated photoluminescence (PL) and time‐resolved photoluminescence (TRPL) spectroscopy. As the temperature is increased, the peak energy of DUV‐AlGaN/AlGaN MQWs PL emission (E_p) exhibits a similarly anti‐S‐shaped behavior (blueshift – accelerated redshift – decelerated redshift): E_p increases in the temperature range of 5.9–20 K and decreases for 20–300 K, involving an accelerated redshift for 20–150 K and an opposite decelerated redshift for 150–300 K with temperature increase. Especially at high temperature as 300 K, the slope of the E_p redshift tends towards zero. This temperature‐induced PL shift is strongly affected by the change in carrier dynamics with increasing temperature. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optical characterization of Si-implanted Al0.18Ga0.82N

Both structural and optical activation studies of Si-implanted Al_0.18Ga_0.82N have been made as a function of anneal temperature by using the x-ray rocking curve measurements and photoluminescence (PL) and time-resolved PL (TRPL) measurements. The full width at half maximum values of both (002) and (102) direction $\omega$-rocking curves for the Si-implanted Al_0.18Ga_0.82N samples decrease as the anneal temperature increases from 1150 to 1250 ^°C. The peak widths of the rocking curves for the as-implanted sample are much broader than those for the Si-implanted and annealed samples, indicating the implantation damage recovery after high temperature anneal. With increasing anneal temperature, the PL peak intensity increases and the PL decay becomes slower. The increase of PL intensity and recombination rate is attributed to both an increase of Si-donor activation and lattice damage recovery. These PL and x-ray results are very consistent with the results of anneal temperature-dependent electrical activation study.     

Time-resolved photoluminescence study of Ga In P alloys

The time-resolved photoluminescence spectra of ordered and disordered Ga_0.52In_0.48P alloys were studied at room temperature and at 77 K liquid nitrogen, respectively. The ordered samples have well fitted two exponential processes decay curves and the time constants are sample dependent and have little relationship with the ordering degree. The decay curve of disordered sample shows that it has single exponential process and its lifetime has a tendency of reduction with the decrease of excitation intensity. The photoluminescence spectra with different delay time at 77 K show that the ordered samples exhibit about 6 ∼ 10 meV blue-shift of PL peak energy with the delay time. Received 13 December 2001 Published online 19 July 2002     

Fe掺杂对溶胶凝胶法制备的ZnO: Ni薄膜结构及发光特性的影响

采用溶胶凝胶法在玻璃基片上制备了ZnO及Ni, Fe共掺杂的Zn_0.95-xNi_0.05Fe_xO (x=0, 0.005, 0.01, 0.03, 0.05) 薄膜. 通过扫描电镜(SEM) 和X射线衍射(XRD) 研究了薄膜样品的表面形貌和晶体结构. 结果表明所有样品都具有(002) 择优取向, Fe掺杂导致ZnO: Ni薄膜的晶体质量变差, 晶粒尺寸减小, 但适当的Fe掺杂有利于获得致密、 均匀的薄膜. XPS测试结果表明样品中Ni离子的价态为+2价, Fe离子的价态为+2价和+3价.室温光致发光(PL) 测量表明, 所有样品均观察到较强的紫外发光峰, 蓝光双峰和绿光发光峰. ZnO: Ni薄膜的发光强度可以通过Fe掺杂进行有效调节. 进而我们讨论了Ni, Fe共掺杂ZnO样品的发光机理.     

Identification of excitons,trions and biexcitons in single‐layer WS2

Single‐layer WS₂ is a direct‐gap semiconductor showing strong excitonic photoluminescence features in the visible spectral range. Here, we present temperature‐dependent photoluminescence measurements on mechanically exfoliated single‐layer WS₂, revealing the existence of neutral and charged excitons at low temperatures as well as at room temperature. By applying a gate voltage, we can electrically control the ratio of excitons and trions and assert a residual n‐type doping of our samples. At high excitation densities and low temperatures, an additional peak at energies below the trion dominates the photoluminescence, which we identify as biexciton emission. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Photoconductivity and photoluminescence in chemically deposited films of CdSSe:CdCl2,Ho

Results of the scanning electron microscopy (SEM), X-ray diffraction (XRD), optical absorption, photoconductivity (PC), and photoluminescence (PL) studies for the CdSSe:CdCl₂,Ho films are presented in this paper. The SEM studies of different CdSSe films show a layered growth structure. A crystalline nature of the films is observed in the XRD studies. The regions with stacking fault were also observed in the X-ray diffractograms. The optical absorption spectra of these films show variations corresponding to the band gaps and the grain-sizes obtained under various deposition conditions and also with annealing. The effect of flux, impurities and annealing on the saturated photo to dark current ratio I_pc/I_dc is observed in the PC rise and decay studies. The maximum value of I_pc/I_dc ∼10⁷ is obtained for the impurity doped annealed films. The PL emission spectra of CdSSe films show two emission peaks associated with the annihilation of free excitons and the transitions between shallow donor and deep acceptor states. In CdSSe:CdCl₂,Ho films, two PL emission peaks are observed at 495 nm and 545 nm corresponding to the transitions ⁵S₂→⁵I₈ and ⁵F₃→⁵I₈, respectively, in Ho. The effect of pH on PL and grain size is also included in the present studies.     

Visible photoluminescence from Ge+-implanted SiO2 films thermally grown on crystalline Si

+ -implanted SiO₂ films is studied as a function of different fabricating conditions (implantation dose, annealing temperature and time). The SiO₂ films containing Ge nanocrystals exhibit two photoluminescence (PL) bands peaked at 600 nm and 780 nm. There are two excitation bands in the PL excitation (PLE) spectra. With variation in Ge nanocrystal size, the PL and PLE peak energies show no appreciable shift. The PL and PLE spectral analyses suggest that during the PL process, electron–hole pairs are generated by the E(l) and E(2) direct transitions inside Ge nanocrystals, which then radiatively recombine via luminescent centers in the matrix or at the interface between the nanocrystal/matrix. Received: 27 January 1998/Accepted: 18 March 1998     

Quantitative analysis of the phonon confinement effect in arbitrarily shaped Si nanocrystals decorated on Si nanowires and its correlation with the photoluminescence spectrum

Arrays of single‐crystalline Si nanowires (NWs) decorated with arbitrarily shaped Si nanocrystals (NCs) are grown by a metal‐assisted chemical etching process using silver (Ag) as the noble metal catalyst. The metal‐assisted chemical etching‐grown Si NWs exhibit strong photoluminescence (PL) emission in the visible and near infrared region at room temperature. Quantum confinement of carriers in the Si NCs is believed to be primarily responsible for the observed PL emission. Raman spectra of the Si NCs decorated on Si NWs exhibit a red shift and an asymmetric broadening of first‐order Raman peak as well as the other multi‐phonon modes when compared with that of the bulk Si. Quantitative analysis of confinement of phonons in the Si NCs is shown to account for the measured Raman peak shift and asymmetric broadening. To eliminate the laser heating effect on the phonon modes of the Si NWs/NCs, the Raman measurement was performed at extremely low laser power. Both the PL and Raman spectral analysis show a log‐normal distribution for the Si NCs, and our transmission electron microscopy results are fully consistent with the results of PL and Raman analyses. We calculate the size distribution of these Si NCs in terms of mean diameter (D₀) and skewness (σ) by correlating the PL spectra and Raman spectra of the as‐grown Si NCs decorated on Si NWs. Copyright © 2015 John Wiley & Sons, Ltd.     

Exciton capture and thermal escape in InAs dot-in-a-well laser structures

The photoluminescence (PL), its temperature and power dependences have been studied in InAs quantum dots (QDs) embedded in asymmetric In_xGa_1?y As/GaAs quantum wells (QWs) with variable In_xGa_1?x As compositions in the capping layer. Three stages for thermally activated decay of QD PL intensity have been revealed. A set of rate equations for exciton dynamics (relaxation into QWs and QDs, and thermal escape) are solved to analyze the mechanism of PL thermal decay. The variety of PL intensities and peak positions, as well as the activation energies of PL intensity decay in DWELL structures with different compositions of a capping layer are discussed.     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

退火对非故意掺杂4H-SiC外延材料386 nm和388 nm发射峰的影响

10 K条件下,采用光致发光(PL)技术研究了不同退火处理后非故意掺杂4H-SiC外延材料的低温PL特性.结果发现,在370—400 nm范围内出现了三个发射峰,能量较高的峰约为3.26 eV,与4H-SiC材料的室温禁带宽度相当.波长约为386 nm和388 nm的两个发射峰分别位于~3.21 eV和~3.19 eV,与材料中的N杂质有关.当退火时间为30 min时,随退火温度的升高,386 nm和388 nm两个发射峰的PL强度先增加后减小,且退火温度为1573 K时,两个发射峰的PL强度均达到最大. 关键词： 光致发光 退火处理 能级 4H-SiC