用SAXS和XRD方法研究TiO2纳米颗粒微观结构

用溶胶-凝胶方法制备了TiO₂纳米样品,并对该样品在300℃到800℃温度区域进行了退火处理.应用同步辐射X射线粉末衍射(XRD)方法研究了经不同热处理温度的TiO₂纳米颗粒的结构相变.应用同步辐射小角X射线散射(SAXS)方法研究了TiO₂纳米颗粒的表面分形与界面特性.得到纳米颗粒粒度与退火温度的变化规律,讨论了表面界面特征与相变的关系. 关键词： X射线小角散射 X射线衍射 2纳米颗粒')" href="#">TiO₂纳米颗粒     

利用小角X射线散射技术研究组分对聚酰亚胺/Al2O3杂化薄膜界面特性与分形特征的影响

采用溶胶-凝胶方法制备无机纳米杂化聚酰亚胺(PI),应用同步辐射小角X射线散射(SAXS)方法研究不同组分杂化PI薄膜的界面特性与分形特征.研究结果表明:散射曲线不遵守Porod定理,形成负偏离,说明薄膜中有机相与Al₂O₃纳米颗粒间存在界面层,界面层厚度在0.54 nm到1.48 nm范围内;随无机纳米组分增加,界面层厚度增加,有机相与无机相作用变强;无机纳米颗粒同时具有质量分形和表面分形特征,其分布、集结是一种非线性动力学过程;随组分增加,其质量分形维数降低 关键词： 小角X射线散射 纳米杂化 聚酰亚胺 界面     

SO2/Ni(111)吸附系统局域结构的多重散射团簇理论研究

用多重散射团族方法对SO₂/Ni(111)吸附系统的S原子ls近边X射线吸收精细结构进行了详细的计算和分析,求得吸附系统的局域结构。研究结果证实了SO₂分子在Ni(111)表面是平铺吸附的,其最佳吸附位为fcc三度芯位。吸附分子的S—O键长比气体状态时增长了(0.007±0.002)nm,分子键角∠OSO减小了10°,SO₂距衬底的吸附高度为(0.20±0.02)nm。理论计算与两组实验结果进行了直接比较。 关键词： 局域吸附结构 X射线吸收精细结构 2/Ni(111)')" href="#">吸附系统SO₂/Ni(111) 多重散射团簇方法     

Cu60Zr30Ti10非晶合金弛豫和晶化过程的小角X射线散射研究

应用小角X射线散射技术研究了Cu₆₀Zr₃₀Ti₁₀非晶合金从300到813 K之间微结构的演化情况.发现在淬火状态下Cu₆₀Zr₃₀Ti₁₀非晶合金中存在直径30 nm左右的富Cu区.非晶的结构弛豫包括573 K之前的低温结构弛豫和573 K到玻璃转变温度的高温结构弛豫，弛豫的结果是产生含有有序原子团簇的富Cu区，这些有序原子团簇的富Cu区是随后晶化过程中晶核产生的基础.Porod曲线分析表明，晶化生成的纳米体心立方CuZr相和基体之间有明锐的界面. 关键词： 小角X射线散射 非晶合金 结构弛豫 晶化     

Al2O3薄膜/纳米Ag颗粒复合结构的光吸收谱及增强Raman散射光谱研究

Al₂O₃介质薄膜与纳米Ag颗粒构成的复合结构,被应用于表面增强Raman散射探测实验中,其中Al₂O₃介质薄膜对纳米Ag颗粒的吸收谱及增强Raman散射光谱的影响被特别关注.该复合结构的光学特性表征出纳米Ag颗粒的偶极振荡特性.从光吸收谱中可以看到,其共振吸收谱随Al₂O₃介质薄膜厚度增加而在整个谱域上发生红移,表明纳米Ag颗粒的周围介电常数随Al₂O₃介质薄膜厚度的增加而增大.采用罗丹明6G作为探针原子,6个Raman特征峰的平均增益值作为表征表面增强Raman散射衬底增益程度的量度.实验结果表明,Al₂O₃介质薄膜层的引入提高了纳米Ag颗粒的衬底介电常数,并引起了散射共振的增强,从而使表面增强Raman散射强度提高. 关键词： 纳米Ag薄膜 共振吸收 表面增强Raman散射 介电常数     

氢化金属玻璃Ni24.3Zr75.7H0.65的结构研究

本工作应用X射线大角散射技术测定金属玻璃氢化前后的径向分布函数,以探讨氢化对金属玻璃结构的影响,弄清氢在金属玻璃结构中的位置及其局域环境。 关键词：     

SrTiO3基片的晶体质量及表面粗糙结构的X射线研究

用X射线双晶衍射摇摆曲线以及双晶X射线形貌对两个SrTiO₃基片的单晶质量进行了对比研究，并用X射线掠入射镜面反射及漫散射研究了它们的表面粗糙结构．结果表明，两个SrTiO₃基片中都存在镶嵌缺陷，其中一个样品的晶体质量相对较高．两个样品的表面粗糙结构相差很大，包括均方根粗糙度σ和横向相关长度ξ．σ分别为（0.5±0.1）和（1.3±0.1）nm，ξ分别为（1200±200）和（300±20）nm．样品的表面粗糙将增加Ｘ射线的漫散射强度而降低镜面反射的强度．晶体质 关键词：     

非晶态合金Co81.5B18.5结构的研究

本文叙述了用X射线衍射方法及偏振中子衍射方法对Co_81.5B_18.5非晶合金的结构研究。利用两种数据处理方法,从实验结果中计算了Co_81.5B_18.5的偏干涉函数(PSF),S_ij(Q),和偏简约径向分布函数G_ij(r)。并对这两种结果作了比较。最后计算了一种模型简单单元的中子衍射散射强度,并讨论了这一非晶合金的结构模型。 关键词：     

多重散射团簇方法对吸附系统SO2/Ag(110)的理论分析

利用多重散射团簇方法(MSC)对吸附系统SO₂/Ag(110)的S原子K边X射线吸收精细结构谱(NEXAFS)作了理论分析.研究表明,覆盖度为0.5时,吸附的SO₂的S—O键长比气体状态时增长了(0.014±0.006)nm,OSO键角减小了15°±5°;SO₂分子的S原子处于芯位,但两个O原子处于不对称的位置;分子平面与(110)的夹角约为52°,同时分子平面相对衬底表面法线有一小角度的倾斜.MSC计算证实了该吸附系统存在一介于π^{关键词： X射线吸收精细结构 2/Ag(110)')" href="#">吸附系统SO₂/Ag(110) 多重散射团簇方法}     

非晶Ni88P12合金薄膜的表面形貌特征与晶化行为的研究

采用化学镀的方法在363K和p型Si（100）衬底上制得非晶Ni₈₈P₁₂合金薄膜．利用X射线衍射、X射线光电子能谱、扫描隧道显微镜和原子力显微镜对非晶合金薄膜及其经处理后形成的氧化态、还原态和晶态的结构、组分和表面的形貌特征作了研究，并对它的晶化行为作了初步探讨．结果表明，非晶合金薄膜是由纳米级微粒聚集成微米级颗粒组成；在低于晶化温度条件下经氧化和还原处理后的薄膜表面晶化；在晶化过程中，合金薄膜的非晶纳米微粒转变为微晶后长大成晶粒，其表面结构光滑平坦，几何边界 关键词：     

Magnetic properties of chalcogenide spinel CuCr2Se4 nanocrystals

The magnetic properties of chalcogenide spinel CuCr₂Se₄ nanocrystals have been studied as a function of crystallite size (15-30 nm). A solution-based method is used for the facile synthesis of the nanocrystals with good size control. They have close to cubic morphology with a narrow size distribution and exhibit superparamagnetic behavior at room temperature. The Curie temperature and saturation magnetization of the nanocrystals are lower as compared with the bulk and decrease with decreasing nanocrystal size. A similar trend is observed in the paramagnetic state for the Curie-Weiss temperature and effective magnetic moment. The low temperature magnetization behavior can be qualitatively explained by spin glass dynamics.     

Preparation and luminescent properties of cubic Eu:Y2O3 nanocrystals and comparison to bulk Eu:Y2O3

Y₂O₃:Eu³⁺ nanocrystals were prepared by combustion synthesis. The particle size estimated by X-ray powder diffraction (XRD) was about 10 nm. A blue-shift of the charge-transfer (CT) band in excitation spectra was observed in Y₂O₃:Eu³⁺ nanocrystals compared with bulk Y₂O₃:Eu³⁺. The electronic structure of Y₂O₃ is calculated by density functional method and exchange and correlation have been treated by the generalized gradient approximation (GGA) within the scheme due to Perdew-Burke-Ernzerhof (PBE). The calculated results show that the energy centroid of 5d orbital in nanocrystal has increasing trend compared with that in the bulk material. The bond length and bond covalency are calculated by chemical bond theory. The bond lengths of Y₂O₃:Eu³⁺ nanocrystal are shorter than those of the bulk counterpart and the bond covalency of Y₂O₃:Eu³⁺ nanocrystal also has an increasing trend. By combining centroid shift and crystal-field splitting, the blue-shift of the CT band is interpreted.     

Strong quenching of praseodymium f-f luminescence induced by a surface of Y2SiO5:Pr nanocrystal

The direct comparison of the luminescence decay data obtained for nano- and bulk Y₂SiO₅:Pr³⁺ crystals has revealed that the concentration threshold of luminescence quenching is strikingly low for nanocrystals. Nanocrystal inhomogeneous stress field induced by a surface stimulates the segregation of the doped Pr³⁺ ions within the surface layer that provides the relaxation of elastic tension arising due to the difference of the ionic radii of Pr³⁺ and Y³⁺. The Pr³⁺ irregular distribution in the nanocrystal volume results in the Pr³⁺ local concentration increasing that facilitates the luminescence quenching.     

中子辐照对Pd80Si20与Pd77.5Cu6Si16.5非晶态合金结构的影响

本工作用X射线衍射技术示差扫描量热法(DSC)和内耗测量等手段研究金属-类金属非晶态合金Pd₈₀Si₂₀和Pd_77.5Cu₆Si_16.5中子辐照前后的微观结构变化。结果表明,辐照在两种样品的对关联函数g(r)以及径向分布函数RDF(r)上都引起明显的变化;辐照后样品的晶化温度和晶化热有所提高,结构变得更加无序,Pd₈₀Si₂₀非晶态合金的内耗在T关键词：     

On the surface properties of a nanodiamond

The dependences of the specific surface energy, the surface tension, and the surface pressure on the size, the surface shape, and the temperature of a nanodiamond with a free surface have been investigated using the Mie-Lennard-Jones interatomic interaction potential. The nanocrystal has the form of a parallelepiped faceted by the (100) planes with a square base. The number of atoms N in the nanocrystal varies from 5 to ∞. The isothermal isomorphic dependences of the specific surface energy, its isochoric derivative with respect to the temperature, the surface tension, and the surface pressure on the nanodiamond size have been calculated at temperatures ranging from 20 to 4300 K. According to the results of the calculations, the surface energy under this conditions is positive, which indicates that the nanodiamond cannot be fragmented at temperatures up to 4300 K. The surface pressure for the nanodiamond P _sf (N) ∼ N ^−1/3 is considerably less than the Laplace pressure P _ls (N)^−1/3 ∼ N ^−1/3 for the same nanocrystal at the given values of the temperature, the density, and the number of atoms N. As the temperature increases from 20 to 4300 K, the lowering of the isotherm P _sf (N) is considerably more pronounced than that of the isotherm P _ls (N). At high temperatures, the isotherm P _sf (N) changes the shape of the size dependence and goes to the range of extension of small nanocrystals. It has been demonstrated that the lattice parameter of the nanodiamond can either decrease or increase with a decrease in the nanocrystal size. The most significant change in the lattice parameter of the nanodiamond is observed at temperatures below 1000 K.     

Determination of surface oxygen vacancy position in SnO2 nanocrystals by Raman spectroscopy

Raman spectra acquired from SnO₂ nanocrystals with different sizes show a size-independent Raman mode at ∼574 cm⁻¹. The intensity increases as the nanocrystal size decreases and this tendency is contrary to that of the normal bulk Raman modes. By considering the existence of oxygen vacancies at the nanocrystal surface, we adopt the density functional theory to calculate the Raman spectra with different oxygen vacancy positions and concentrations. The results clearly demonstrate that the in-plane oxygen vacancy is responsible for the 574 cm⁻¹ mode and the intensity enhancement is a result of the higher in-plane oxygen vacancy concentration.     

Third order optical nonlinearities in ZnFe2O4 nanocrystals

Using Z-scan method with picosecond laser at 532 nm, the third order optical nonlinearities of ZnFe₂O₄ were investigated. The nonlinear refractive index is positive for all ZnFe₂O₄ samples and decrease with the nanocrystal size. The nonlinear absorption dominated by saturable absorption for 19 nm and 11 nm ZnFe₂O₄ but by two photon absorption for 5 nm ZnFe₂O₄ organosol. Origin of the optical nonlinearities and the size effect has been discussed.     

Formation of ultrathin nanocomposite SiO2:nc-Au structures by Pulsed Laser Deposition

A method for the formation of Au nanocrystal (nc) arrays embedded in an ultrathin SiO₂ layer in one vacuum cycle is proposed. The method is based on the co-deposition in vacuum of ∼1 nm thick uniform Si-Au amorphous layer at a specific composition ratio by Pulsed Laser Deposition on the pre-oxidized Si(1 0 0) substrate, followed by its oxidation in the glow discharge oxygen plasma at room temperature, resulting in the precipitation of Au ncs at the bottom interface and/or at the surface of the forming SiO₂ layer. The capping SiO₂ layer is formed by the glow discharge plasma oxidation of further deposited ultrathin Si layer. Au ncs 2-5 nm in size and with the separation of ∼3-20 nm from each other segregate during the oxidation of Au-Si mixture as evidenced by transmission electron microscopy (TEM). The evolution of Au and Si chemical state upon each step of the SiO₂:nc-Au nanocomposite structure formation is monitored in situ by X-ray photoelectron spectroscopy (XPS). The metrology of nanocomposite SiO₂:nc-Au structures describing the space distribution of Au ncs as a function of Au/Si ratio is presented.     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

The temperature dependence of nanocrystal heat capacity

The temperature dependence of the specific (per atom) entropy and heat capacity of a nanocrystal is studied using a nanocrystal model in the form of a rectangular parallelepiped with variable surface shape. Accounting for the temperature dependence of the surface energy showed that the temperature dependence of the surface contribution to specific entropy is described by the same function that determines the temperature dependence of the isochoric heat capacity of a macrocrystal. Thus, at T → 0 K at T/Θ > 2 the surface contribution to the specific heat is zero. The maximal surface contribution to specific heat is reached at T/Θ = 0.2026 and is equal to c _st/k _B = 1.0115 (where k _B is the Boltzmann constant, Θ is the characteristic temperature depending both on the size and the shape of the nanocrystal). The applicability of the Grüneisen rule for a nanocrystal both at low and high temperatures is studied. It has been found that a case when the surface contribution to specific heat would be negative c(N) < c(∞), i.e. c _st(N) < 0 can occur for nanocrystals with a noncubic habitus.