采用硅离子注入改进SIMOX埋氧的抗总剂量辐射性能研究

采用硅离子注入工艺对注氧隔离(SIMOX)的绝缘体上硅(SOI)材料进行改性, 在改性材料和标准SIMOX材料上制作了部分耗尽环型栅NMOS/SOI晶体管, 并对其进行⁶⁰Co γ射线总剂量辐照试验. 通过背栅的I-V特性表征晶体管的总剂量辐照特性. 结果表明, 在埋氧层注硅可以降低NMOS/SOI受辐照引起的背栅阈值电压漂移, 提高埋氧层的抗总剂量能力.     

埋氧注氮工艺对部分耗尽SOI PMOSFET顶栅氧的辐射硬度的影响

研究了埋氧注氮对部分耗尽SOI PMOSFET顶栅氧的总剂量辐射硬度所造成的影响。注入埋氧的氮剂量分别是8×1015 , 2×1016 和1×1017cm-2。实验结果表明，辐照前，晶体管的阈值电压随氮注入剂量的增加向负方向漂移。在正2V的栅偏压下，经5×105 rad(Si)的总剂量辐照后，同埋氧未注氮的晶体管相比，埋氧注氮剂量为8×1015 cm-2的晶体管呈现出了较小的阈值电压漂移量。然而，当注氮剂量高达2×1016 和 1×1017cm-2时，所测大多数晶体管的顶栅氧却由于5×105 rad(Si)的总剂量辐照而受到了严重损伤。另外，对于顶栅氧严重受损的晶体管，其体-漏结也受到了损伤。所有的实验结果可通过氮注入过程中对顶硅的晶格损伤来解释。     

高功率微波作用下热载流子引起n型金属-氧化物-半导体场效应晶体管特性退化研究

高功率微波(HPM)通过使半导体器件特性退化和功能失效,从而干扰电子系统无法正常工作. 针对金属氧化物半导体(MOS)器件的HPM效应, 建立了高功率微波引起n型金属氧化物半导体场效应晶体管(nMOSFET)特性退化的物理过程与模型. 器件仿真结果中nMOSFET的输出特性曲线显示栅极注入HPM引起器件特性退化,包括阈值电压正向漂移、 饱和电流减小、跨导减小等;结合物理模型分析可知, HPM引起的高频脉冲电压使器件进入深耗尽状态, 热载流子数目增多,热载流子效应导致器件特性退化. MOS器件的HPM注入实验结果显示,器件特性曲线、器件模型参数变化趋势与仿真结果一致, 验证了HPM引起nMOSFET特性退化的物理过程与模型.     

AlGaN/GaN双异质结F注入增强型高电子迁移率晶体管

理论模拟了不同GaN沟道厚度的双异质结(AlGaN/GaN/AlGaN/GaN)材料对高电子迁移率晶体管(HEMT)特性的影响,并模拟了不同F注入剂量下用该材料制作的增强型器件的特性差异.采用双异质结材料,结合F注入工艺成功地研制出了较高正向阈值电压的增强型HEMT器件.实验研究了三种GaN沟道厚度制作的增强型器件直流特性的差异,与模拟结果进行了对比验证.采用降低的F注入等离子体功率,减小了等离子体处理工艺对器件沟道迁移率的损伤,研制出的器件未经高温退火即实现了较高的跨导和饱和电流特性.对14 nm GaN沟道厚度的器件进行了阈值电压温度稳定性和栅泄漏电流的比较研究,并且分析了双异质结器件的漏致势垒降低效应.     

SIMOX SOI埋氧注氮工艺对埋氧中固定正电荷密度的影响

在SIMOX SOI材料的埋氧中注氮是为了增强该类材料的抗辐射能力.通过C-V研究表明，对于埋氧层为150 nm的SIMOX SOI材料来说，当在其埋氧中注入4×10¹⁵cm^-2剂量的氮后，与未注氮埋氧相比，注氮埋氧中的固定正电荷密度显著增加了；而对于埋氧层为375nm的SIMOX SOI材料来说，当注氮剂量分别为2×10¹⁵cm^-2和3×10¹⁵cm^{-2关键词： SIMOX 埋氧 注氮 固定正电荷密度}     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用60 Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一.     

超薄栅下LDD nMOSFET器件GIDL应力下退化特性

对1.4nm超薄栅LDD nMOSFET器件栅致漏极泄漏GIDL(gate-induced drain leakage)应力下的阈值电压退化进行了研究.GIDL应力中热空穴注进LDD区界面处并产生界面态，这导致器件的阈值电压变大.相同栅漏电压V_DG下的不同GIDL应力后阈值电压退化量的对数与应力V_D/V_DG的比值成正比.漏偏压V_D不变的不同GIDL应力后阈值电压退化随着应力中栅电压的增大而增大，相同栅偏压V_G下的不同GIDL应力后阈值电压退化也随着应力中漏电压的增大而增大，这两种应力情形下退化量在半对数坐标下与应力中变化的电压的倒数成线性关系，它们退化斜率的绝对值分别为0.76和13.5.实验发现器件退化随着应力过程中的漏电压变化远大于随着应力过程中栅电压的变化. 关键词： 栅致漏极泄漏 CMOS 阈值电压 栅漏电压     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用⁶⁰Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一. 关键词： AlGaN/GaN HEMT器件 γ射线辐射 表面态     

应变Si沟道nMOSFET阈值电压模型

在研究分析弛豫SiGe衬底上的应变Si 沟道nMOSFET纵向电势分布的基础上,建立了应变Si nMOSFET阈值电压模型,并利用该模型对不同的器件结构参数进行仿真,获得了阈值电压与SiGe层掺杂浓度和Ge组分的关系、阈值电压偏移量与SiGe层中Ge组分的关系、阈值电压与应变Si层掺杂浓度和厚度的关系. 分析结果表明：阈值电压随SiGe层中Ge组分的提高而降低,随着SiGe层的掺杂浓度的提高而增大;阈值电压随应变Si层的掺杂浓度的提高而增大,随应变Si层厚度增大而增大. 该模型为应变Si 器件阈值电压设计 关键词： 应变硅 阈值电压 电势分布 反型层     

AlGaN/GaN槽栅HEMT模拟与实验研究

分析了栅槽深度对AlGaN/GaN HEMT特性的影响,并对不同栅槽深度的器件特性进行了模拟,得到了器件饱和电流、最大跨导和阈值电压随栅槽深度的变化规律.当槽栅深度增大,器件饱和电流逐渐下降,而最大跨导逐渐增大,阈值电压向X轴正方向移动.研制出不同栅槽深度的蓝宝石衬底AlGaN/GaN HEMT,用实验数据验证了得到的不同栅槽深度器件特性变化规律.从刻蚀损伤和刻蚀引入界面态的角度分析了模拟与实验规律产生差别的原因. 关键词： 高电子迁移率晶体管 AlGaN/GaN 槽栅器件     

Research on total-dose hardening for H-gate PD NMOSFET/SIMOX by ion implanting into buried oxide

In this work,we investigate the back-gate I-V characteristics for two kinds of NMOSFET/SIMOX transistors with H gate structure fabricated on two different SOI wafers.A transistors are made on the wafer implanted with Si+ and then annealed in N2,and B transistors are made on the wafer without implantation and annealing.It is demonstrated experimentally that A transistors have much less back-gate threshold voltage shift AVth than B transistors under X-ray total dose irradiation.Subthreshold charge separation technique is employed to estimate the build-up of oxide charge and interface traps during irradiation,showing that the reduced △Vth for A transistors is mainly due to its less build-up of oxide charge than B transistors.Photoluminescence (PL) research indicates that Si implantation results in the formation of silicon nanocrystalline (nanocluster) whose size increases with the implant dose.This structure can trap electrons to compensate the positive charge build-up in the buried oxide during irradiation,and thus reduce the threshold voltage negative shift.     

Influence of nitrogen implantation into the buried oxide on the radiation hardness of silicon-on-insulator wafers

In order to improve the total-dose radiation hardness of the buried oxide of separation by implanted oxygen silicon-on-insulator wafers, nitrogen ions were implanted into the buried oxide with a dose of 1016 cm-2 , and subsequent annealing was performed at 1100°C. The effect of annealing time on the radiation hardness of the nitrogen implanted wafers has been studied by the high frequency capacitance-voltage technique. The results suggest that the improvement of the radiation hardness of the wafers can be achieved through a shorter time annealing after nitrogen implantation. The nitrogen-implanted sample with the shortest annealing time 0.5 h shows the highest tolerance to total-dose radiation. In particular, for the 1.0 and 1.5 h annealing samples, both total dose responses were unusual. After 300-krad(Si) irradiation, both the shifts of capacitance-voltage curve reached a maximum, respectively, and then decreased with increasing total dose. In addition, the wafers were analysed by the Fourier transform infrared spectroscopy technique, and some useful results have been obtained.     

Radiation response of pseudo-MOS transistors fabricated in hardened fully-depleted SIMOX SOI wafers

The total dose radiation response of pseudo-MOS transistors fabricated in hardened and unhardened FD (fully-depleted) SIMOX (Separation by Implanted Oxygen) SOI (Silicon-on-insulator) wafers is presented.At 1 Mrad(Si) radiation dose, the threshold voltage shift of the pseudo-MOS transistor is reduced from -115.5 to -1.9 V by the hardening procedure.The centroid location of the net positive charge trapped in BOX, the hole-trap density and the hole capture fraction of BOX are also shown.The results suggest that hardened FD SIMOX SOI wafers can perform well in a radiation environment.     

Improvement of total-dose irradiation hardness of silicon-on-insulator materials by modifying the buried oxide layer with ion implantation

The hardening of the buried oxide (BOX) layer of separation by implanted oxygen (SIMOX) silicon-on-insulator (SOI) wafers against total-dose irradiation was investigated by implanting ions into the BOX layers. The tolerance to total-dose irradiation of the BOX layers was characterized by the comparison of the transfer characteristics of SOI NMOS transistors before and after irradiation to a total dose of 2.7 Mrad(SiO₂. The experimental results show that the implantation of silicon ions into the BOX layer can improve the tolerance of the BOX layers to total-dose irradiation. The investigation of the mechanism of the improvement suggests that the deep electron traps introduced by silicon implantation play an important role in the remarkable improvement in radiation hardness of SIMOX SOI wafers.     

Total dose radiation response of modified commercial silicon-on-insulator materials with nitrogen implanted buried oxide

Nitrogen ions of various doses are implanted into the buried oxide(BOX) of commercial silicon-on-insulator(SOI) materials,and subsequent annealings are carried out at various temperatures.The total dose radiation responses of the nitrogen-implanted SOI wafers are characterized by the high frequency capacitance-voltage(C-V) technique after irradiation using a Co-60 source.It is found that there exist relatively complex relationships between the radiation hardness of the nitrogen implanted BOX and the nitrogen implantation dose at different irradiation doses.The experimental results also suggest that a lower dose nitrogen implantation and a higher post-implantation annealing temperature are suitable for improving the radiation hardness of SOI wafer.Based on the measured C-V data,secondary ion mass spectrometry(SIMS),and Fourier transform infrared(FTIR) spectroscopy,the total dose responses of the nitrogen-implanted SOI wafers are discussed.     

氮氟复合注入对注氧隔离SOI材料埋氧层内固定正电荷密度的影响

为了抑制埋层注氮导致的埋层内正电荷密度的上升, 本文采用氮氟复合注入方式, 向先行注氮的埋层进行了注氮之后的氟离子注入, 并经适当的退火, 对埋层进行改性. 利用高频电容-电压 (C-V) 表征技术, 对复合注入后的埋层进行了正电荷密度的表征. 结果表明, 在大多数情况下, 氮氟复合注入能够有效地降低注氮埋层内的正电荷密度, 且其降低的程度与注氮后的退火时间密切相关. 分析认为, 注氟导致注氮埋层内的正电荷密度降低的原因是在埋层中引入了与氟相关的电子陷阱. 另外, 实验还观察到, 在个别情况下, 氮氟复合注入引起了埋层内正电荷密度的进一步上升. 结合测量结果, 讨论分析了该现象产生的原因. 关键词： 绝缘体上硅(SOI) 材料 注氮 注氟 埋氧层正电荷密度     

Ground state magnetic properties of ultrathin fcc Fe and Co films on Cu(001) surfaces

The oxidation characteristics of silicon implanted with a low dose of nitrogen (1–3×10¹⁵cm^–2) have been studied for dry oxidation conditions at 1020°C. The wafers were subjected to a pre-oxidation annealing. Complete inhibition of the oxide growth occurs in the initial stage of oxidation, while the oxidation rate for prolonged oxidation is identical to that for pure silicon. The oxidation resistance increases with the implantation dose. The resistance is attributed to the formation of a nitrogen-rich surface film during annealing. This layer, which consists of only a few monolayers, is presumably composed of oxynitride. The electrical characteristics of MOS capacitors formed on implanted wafers show that the interface state density is not significantly increased by the low-dose N implantation.     

Defects in separation by implanted oxygen wafer probed by monoenergetic positron beams

Defects in the separation by implanted oxygen (SIMOX) wafers were studied by monoenergetic positron beams. For the as-implanted specimen, vacancies introduced by ion implantation were found to form vacancy-oxygen complexes. After high temperature annealing, a drastic increase in the formation probability of positronium was observed. This suggests an introduction of open-spaces by the formation of an amorphous SiO₂. The present investigation shows that positrons provide a nondestructive probe for the detection of defects in SIMOX wafers and microstructures of SiO₂.