集成光学条波导阵列与单模光纤阵列的联接

本文报告了一种新的集成光学条波导阵列与镶嵌在硅V槽中的单模光纤阵列耦合联接方法的设计考虑,导出了确定光纤正确位置及V型槽的几何尺寸的若干计算公式.并讨论了光纤与波导几何尺寸与耦合效率的关系.指出了这是实现单模光纤阵列与条波导阵列的固定联接的有效方法,它简化了波导与光纤的对准程序,即由五维调整简化为平面的一维调整.可实现多个波导和多个光纤的同时对准与固定.最大限度地利用了有效重叠面积,从而提高了光纤与条波导的耦合效率.一组典型的数据是单模光纤(芯径10μm)对单模波导(10μm×5μm)的耦合效率可达55%,而同样尺寸的波导对光纤的最大耦会效率可达86%.     

阵列波导光栅的简便模拟方法及应用

结合等效折射率方法并利用高斯光束近似给出了一种简便的模拟计算阵列波导光栅方法,可实现AWG锔模拟模拟计算结果与理论公式计算结果吻合利用这种模拟方法,模拟了一个阵列波导光栅(AWG)实例,并考察了阵列波导条数对器件性能的影响,最后分析了制造工艺误差对器件性能的影响     

修正的光束传输法在阵列波导光栅中的应用

以亥姆赫兹方程为基础,对传统的有限差分光束传播法进行修正,提出一种修正后的新算法,将修正后的算法与传统算法进行了比较,并给出了用其计算阵列波导光栅中的传输光场的应用结果.通过比较计算结果和应用结果得出结论：修正后的算法可以准确计算光波场,并提高了计算精确度,有一定实用价值.     

多波导阵列耦合研究

提出了一种求解波导阵列耦合特性的方法.采用拉普拉斯变换,将同时考虑相邻和次相邻波导耦合作用的波导阵列耦合模方程组变为一个线性方程组,利用矩阵的LU分解法(将系数矩阵分解为单位下三角阵L与上三角阵U的乘积)求出该线性方程组的解.然后根据给定的初始条件进行拉普拉斯变换反演,求出耦合模方程组的解.采用该方法研究了五波导阵列,光从中间一个波导入射和从五个波导入射时的耦合特性,给出了每个波导中光功率变化规律曲线,并将所得结果与同样条件下仅考虑相邻波导耦合的结果做了比较.采用该方法可以求出任意数目波导组成的阵列,考虑任意波导之间耦合的耦合模方程组的解.     

掺铒光波导放大器的速率方程分析

用重合积分的方法 ,分析了描述掺铒光波导放大器 (EDWA)的速率方程 ,得到了 980nm波段抽运的掺铒光波导放大器增益的隐式解析解 ,在此基础上得到了抽运阈值功率的解析表达式。计算了掺铒平面光波导放大器中的光场与铒掺杂浓度分布的重叠因子。讨论了铒掺杂浓度对抽运阈值功率的影响及抽运功率对增益的影响。     

铌酸锂波导电光重叠积分因子的波长依赖特性分析

通过测量铌酸锂(LN)单模波导在不同波长下的半波电压,结合半波电压与电光重叠积分因子的依赖关系,实验发现了LN单模波导电光重叠积分因子随波长增大而迅速减小.另一方面,通过数值求解法分别得出了LN单模波导在不同波长的导模场分布和调制电场分布以及二者的重叠积分因子,在理论上获得了与实验数据十分近似的结果.进一步的仿真分析指出LN单模波导电光重叠积分因子随波长增大而减小的规律主要来自于导模的光场中心随波长增大逐渐远离波导表面,向低电场强度区域靠近.这种电光重叠积分因子的波长依赖特性是导致LN波导半波电压随波长增大而非线性上升的原因之一,它将为基于LN波导的器件的设计和优化提供重要参考.     

新型电光扫描器中光波导阵列特性研究

利用有限差分光束传输法(FD-BPM)详细研究了光波导阵列电光扫描器的核心部件—光波导阵列的传输特性和辐射特性,分析了光波导阵列结构参量对其传输特性和辐射特性的影响.研究结果表明,光波导芯层厚度、光波导阵列的周期、长度和层数对光波导阵列输出面上的光场振幅、相位分布及光波导阵列输出光束主瓣的半峰值全宽度(FWHM)影响很大.通过与其它理论研究的结果进行比较指出,FD-BPM可以很方便地、更全面地描述光波导阵列的传输和辐射特性.另外,在研究光波导阵列光束扫描的基础上,根据光波导阵列电光扫描器的扫描探测要求,提出了光波导阵列结构优化设计的原则.     

一种温度不敏感型阵列波导光栅的研究

研究了的一种新型温度不敏感型阵列波导光栅(AWG)。该新型温度不敏感型阵列波导光栅的波导采用混合材料的波导结构，该混合材料波导通过在石英波导芯层上旋涂聚合物材料的上包层，达到改变波导温度特性的目的，使得阵列波导光栅的温度敏感性降低。通过理论分析和有限差分方法研究了其中两种结构：三层混合材料波导构成的阵列波导光栅和四层混合材料波导构成的阵列波导光栅，计算了该新型温度不敏感型阵列波导光栅的温度特性。结果表明，在一定的设计下，温度变化0～50℃时，这两种温度不敏感型阵列波导光栅的最大波长漂移量小于0．03nm，不到无温度控制时常规阵列波导光栅最大波长漂移量的4％。     

掺铒玻璃波导放大器中抽运光信号光重叠因子分析

通过分析掺铒(Er3 )玻璃波导放大器(EDWA)的放大增益机理,提出抽运光与信号光光模场分布之间的归一化重叠积分因子(Γ),并引入到掺铒波导放大器增益模拟计算中,使理论模型更切合实际。以Ag -Na 二次离子交换工艺制作的具有埋入型渐变折射率分布的掺铒波导放大器为例,采用数值方法模拟了条形波导截面上的二维折射率分布及抽运光、信号光的光模场分布。计算了不同工艺参量设置下的Γ大小,讨论Γ对放大器增益的影响。结果显示,在二次离子交换制作过程中设置适当工艺参量优化折射率分布,能有效改善波导中抽运光与信号光光模场分布之间的重叠因子,提高掺铒波导放大器的增益。计算结果显示,在一定条件下,Γ从0.5增至0.8,每厘米长度掺铒波导放大器的放大增益可提高近1.5 dB。     

AWG中波导间耦合造成的相位畸变的分析

用(1,1)阶Pad啨近似的广角BPM计算了阵列波导光栅(AWG)中由于阵列波导间耦合造成的相位畸变以及由于相位畸变引起的相位误差分别考虑了光从中心/非中心输入波导入射两种情况结果表明,波导间的耦合会造成显著的相位畸变,但由此引起的相位误差却很小,光从中心输入波导入射时对应的相位误差10-3rad,从非中心输入波导入射时的相位误差约为10-2rad针对波导阵列边缘效应引起的相位畸变,设计AWG结构时,在阵列部分两侧增加了边缘辅助波导结构,从而消除了边缘效应,使得边缘阵列波导对应的相位误差从10-1rad量级减小为10-3(10-2)rad量级.     

Mode energy transformation between two connected multimode general square-law-index optical waveguides

A coherent states method is used to investigate the mode coupling coefficients in the most general buttjoint problem for two multimode general square-law-index optical waveguides, when two different waveguides with elliptical cross-sections are to be butt-jointed with axis displacement, tilt and some turning of symmetry axes with respect to each other. The explicit expressions for the mode coupling coefficients and recurrence relations for the mode overlap integrals are obtained; the sum rules for the mode coupling coefficients are formulated and a method of experimental data analysis is proposed for this general problem. The method of calculating mode coupling coefficients is proposed for the case of the butt-joint problem when the waveguide cross-sections are only partially overlapping and then it is used to investigate the influence of misalignment on mode power distribution and pulse dispersion in the second waveguide. The experimental data are compared and it is shown that the coupling coefficients obtained in square-law-index model can be used in dispersion calculations forα-profile fibres in the case when the valueα is not far from the valueα=2.     

Three-dimensional hybrid modeling based on a beam propagation method and a diffraction formula for an AWG demultiplexer

An efficient and accurate three-dimensional (3D) hybrid modeling, which combines a 3D beam propagation method (BPM) and the two-dimensional (2D) Kirchhoff–Huygens diffraction formula, is developed to simulate the field propagation in an arrayed waveguide grating (AWG) demultiplexer. The 2D Kirchhoff–Huygens diffraction formula is used for the simulation of the light propagation in the free propagation regions (FPRs). A 3D BPM in a polar coordinate system is used to simulate the light propagation in the transition region between the input FPR and the arrayed waveguides so that the coupling coefficients for the arrayed waveguides are calculated conveniently and accurately. For the simulation in the transition region between the arrayed waveguides and the output FPR, only the central arrayed waveguide and several adjacent ones are needed in the computational window of a standard BPM and thus the computation efficiency is improved. Finally, a flat-top AWG is designed and fabricated to verify the reliability of the present simulation method. The calculated and measured spectral responses are in a good agreement.     

Mode coupling between two connected multimode parabolic-index optical waveguides

Both a displacement of axis and a change in the refractive index distribution function cause mode coupling to occur between two multimode parabolic-index optical waveguides. This coupling is investigated by the coherent states method and the method of the dynamical symmetry group. Expressions for the mode coupling coefficients are obtained and their relationship to the Franck-Condon factors is emphasized. Recurrence relations for the mode overlap integrals and sum rules for the mode coupling coefficients are presented. An analogue of the Franck-Condon principle for the mode coupling coefficients is formulated. A simple geometric method for finding the most intensively coupled modes is also proposed.     

小尺寸低折射率差硅基二氧化硅阵列波导光栅

随着AWG型器件在光通信系统中的大规模应用,对低成本AWG芯片的需求越来越多。在各种降成本方案中,减小AWG芯片的尺寸是最有效的方法之一。本文介绍了一种新型小尺寸低折射率差硅基二氧化硅阵列波导光栅（AWG）的设计。在该AWG中,输入波导/输出波导与平板波导连接的部分制作成两侧为空气槽的高折射率差波导,所以在与输出平板波导连接处的相邻输出波导间距较小,这样可以在设计上缩短平板波导的长度、减少阵列波导的数量,实现较小的AWG芯片尺寸。该AWG的其它部分,如输入/输出波导与光纤耦合的部分、阵列波导光栅等均采用常规的低折射率波导工艺,所以就同时具有与常规的低折射率波导AWG相同的优点：如低耦合损耗、较好的串扰以及光学特性等。根据这个原理,设计了一种40通道100 GHz频率间隔的低折射率差硅基二氧化硅AWG,其芯片尺寸只有23.88 mm?10.5 mm,是传统相同材料制作的AWG尺寸的1/6。     

An Analytical Model for the Coupling Between the Array Waveguides in AWGs and Star Couplers

The purpose of this paper is to present an accurate analytical solution for the coupling between the array waveguides in arrayed waveguide grating (AWG) devices and star couplers. The results of this analysis will be useful for developing numerical models of AWGs and star couplers, as well as other optical waveguide components containing arrays of coupled waveguides.     

阵列波导光栅平坦化的研究

阵列波导光栅的平坦化在实际应用中有很重要的意义.本文系统地研究了阵列波导光栅的平坦化.在输入波导、输出波导、阵列波导输入端与输出端上分别引入了指数型锥形波导.通过改变锥形波导的形状和尺寸来实现平坦化的优化.本文首先从理论上论述了引入指数型锥形波导的输出光谱特性,给出了结构参量的关系表达式,阐明了输入波导处的锥形波导是影响输出光谱平坦化的主要因素,阵列波导和输出波导处的锥形波导对输出光谱的平坦化有一定的影响.其次采用数值模拟的方法模拟了输出光谱,优化了结构参量,总结出了指数型锥形波导对平坦化影响的趋势和规律.模拟结果显示,输出光谱1 dB带宽大于通道间隔的50%,插入损耗从5.2 dB减小到了4.0 dB,串扰小于-30 dB.最后,本文给出了实验结果,插入损耗减小了0.87 dB,串扰减小了3.67 dB,1 dB带宽增加0.1 nm,增加了54.7%.实验结果表明引入指数型锥形波导提高了阵列波导光栅器件的光谱性能.     

Grating-assisted coupling of optical fibers and photonic crystal waveguides

We propose and analyze a highly efficient method of coupling light from optical fibers to two-dimensional photonic crystal waveguides. Efficient coupling is achieved by positioning of a tapered fiber parallel to the linear defect, where the photonic crystal's cladding functions as a grating coupler and provides field confinement as well. Numerical simulations indicate that better than 90% transmission is possible with a full width at half-magnitude bandwidth of 12nm. It is shown that one can increase the bandwidth by increasing the field overlap between the two waveguides.     

方向耦合器结构参量的新型设计方法

本文应用束传播与重叠积分方法,考虑输入波导区、耦合区和输出波导区整体结构,提出了方向耦合器结构参量的新型设计方法.与耦合模及局部模等方法相比,该方法具有计算简便,结果精确等优点.     

A concise design of 16 × 16 polymer AWG with low insertion loss and crosstalk

In this paper, a 16-channel arrayed waveguide grating multiplexer (AWG) has been designed using polymer materials with 1.5% refractive index difference. Certain important parameters are optimized using the coupling mode theory and Beam Propagation Method. The factors that affect the insertion loss and the crosstalk are analyzed in this paper. In our design we introduced the parabolic taper structure and evaluated the suitable number of the arrayed waveguide, obtaining a total insertion loss of 2.19 dB. For obtaining a low crosstalk we evaluate the pitches of adjacent input/output waveguides ΔX and arrayed waveguides d as different values. We chose the value of ΔX about 2.5 times of d by enlarging the pitches of adjacent input/output waveguides. The crosstalk of the designed AWG is lower than −40 dB.     

Parameter optimization and structural design of polymer arrayed waveguide grating multiplexer

First some important parameters are optimized for the structural design of a polymer arrayed waveguide grating (AWG) multiplexer around the central wavelength of 1.55 μm with the wavelength spacing of 1.6 nm. These parameters include the thickness and width of the guide core, mode effective refractive indices and group refractive index, diffraction order, pitch of adjacent waveguides, length difference of adjacent arrayed waveguides, focal length of slab waveguides, free spectral range (FSR), the number of input/output (I/O) channels, and that of arrayed waveguides. Then the bent angles, radii and lengths of all the input/output channels and arrayed waveguides are determined. Finally, a schematic waveguide layout of this device is presented, which contains 2 slabs, 11 input channels, 11 output channels, and 91 arrayed waveguides.