苯乙烯/丙烯酸正丁酯乳液聚合反应过程中残余单体含量的实时监测

采用近红外光谱分析技术在线测量苯乙烯(St)/丙烯酸正丁酯(BA)乳液聚合体系中残余单体的含量. 共设计9个半连续方式的St/BA乳液共聚反应, 在反应过程中实时取样测量其残余单体含量, 并记录取样时刻对应的聚合体系的近红外光谱. 采用多元散射校正法(MSC)处理光谱, 有效地克服了乳胶粒子散射效应对近红外光谱分析的影响. 采用主成分分析法(PCA)对乳液体系的近红外光谱数据进行了解析. 选取6个聚合反应对应不同反应时间的72个样品, 用于建立校正模型, 另外3个聚合反应共取36个样品用于校正模型的验证, 并在反应设计上体现了乳化剂用量的变化, 从而使校正模型对乳化剂用量的变化具有一定的适应性. 研究结果表明, 所得模型对残余单体St和BA含量的预测结果标准差(SEP)分别为0.08026和0.05305.     

水溶性和油溶性引发剂引发γ-甲基丙烯酰氧基丙基三甲氧基硅烷/苯乙烯细乳液共聚合的比较

分别用水溶性的过硫酸钾(KPS)和油溶性的2,2′-偶氮二异丁腈(AIBN)为引发剂引发γ-甲基丙烯酰氧基丙基三甲氧基硅烷(MPS)/苯乙烯(St)细乳液共聚合反应.比较了两类引发剂对MPS/St共聚合动力学(包括硅氧烷水解动力学和MPS/St的自由基共聚合动力学)、乳胶粒稳定性和共聚产物微结构的影响.     

蒽在SDS/BA/H2O体系中的光谱特征

用紫外-可见吸收光谱和荧光发射光谱研究了蒽在不同组成和结构的十二烷基硫酸钠(SDS)/苯甲醇(BA)/H20微乳液中的光谱特征,探讨了微乳液组成和结构对蒽光谱特征的影响,阐述了蒽在微乳液中的定位。结果表明,蒽位于O/W微乳液的膜相和油核;在SDS/BA/H2O W/O微乳液中,蒽定位于油连续相。     

活性正离子聚合与原子转移自由基聚合转换合成聚β-蒎烯接枝共聚物

通过活性正离子聚合与原子转移自由基聚合(ATRP)转换合成了β-蒎烯与甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)、苯乙烯(St)的新型接枝共聚物.首先以α-氯代乙苯/TiCl4/Ti(OiPr)4/nBu4NCl体系引发β-蒎烯活性正离子聚合,合成预定分子量大小和窄分子量分布的聚β-蒎烯,然后经N-溴代琥珀酰亚胺(NBS)定量溴化,得到溴化聚β-蒎烯大分子引发剂(Br/β-蒎烯链节摩尔比为0.5).然后将该大分子引发剂与溴化亚铜(CuBr)/2,2′-联吡啶(bpy)复合,引发MMA、BA、St进行ATRP接枝聚合.接枝反应显示一级动力学特征,且产物的分子量及分子量分布可控,表明上述ATRP接枝聚合反应具有可控聚合特征.接枝产物的结构经1H-NMR分析得到进一步证实.     

顶空气相色谱测定含铅透明塑料中挥发性组分及含量

将一定量含铅透明塑料样品置于密闭顶空瓶内,在100℃加热平衡60 min,取上层气体进行检测,得出挥发性物质主要为丙烯酸正丁酯(BA)和苯乙烯(St),其含量分别为86.2和3.52 mg/g,相对标准偏差是6.6%和8.1%。加标回收实验表明,BA与St的平均回收率分别为60.2%和60.8%。将含铅透明塑料在80℃热处理50 h后,挥发性组分BA和St含量降为未处理时的63.88%和52.16%; 100℃热处理50 h后,BA和St含量降为未处理时的37.39%和10.97%。因此,高温处理能够有效降低材料当中残留的挥发性组分。     

超声无皂乳液聚合制备BA/St/AM三元共聚物乳胶粒及其聚合机理研究

将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.     

有机硅氧烷改性St/BA/AA三元共聚乳液的制备

采用核壳乳液聚合法,制备了乙烯基三乙氧基硅烷（VTES）改性的St/BA/AA三元共聚乳液,其结构经FT IR确证。研究了VTES用量、乳化剂用量及配比和引发剂用量对单体转化率和粒径的影响。结果表明：在最优条件［48%St, 48%BA, 4%AA, 1%N-MA, 4%VTES, 8%乳化剂（OP-10/SDS=1/3）, 0.8%引发剂］下,单体转化率为95.8%,平均粒径242 nm。并研究了改性St/BA/AA乳胶膜(1)的耐溶剂性和铅笔硬度。结果表明：1具有良好的耐溶剂性,铅笔硬度为2H。     

苯乙烯/N-苯基马来酰亚胺共聚物分子量测定和模型

从内聚能的角度建立了含共聚组成、序列不均匀性的共聚物分子量及分布理论,导出其计算式.将凝胶渗透色谱(GPC)与紫外吸收光谱(UV)和示差折光仪(DR)串接,测定苯乙烯(St)/N-苯基马来酰亚胺(PMI)共聚物的分子量.根据St/PMI共聚合原理,对St-PMI共聚物的分子量进行模型化,该模型能较好地预测引发剂、单体配比、转化率对共聚物分子量的影响.     

TEM研究苯乙烯微乳液聚合机理

用透射电镜(TEM)对苯乙烯(St)/十二烷基硫酸钠(SDS)/正戊醇/水的O/W微乳液体系在反应前、聚合过程中和反应结束后等不同时间里进行观察,并测定苯乙烯微乳液聚合前后粒径的大小,根据粒径大小的变化研究苯乙烯微乳液聚合成核机理,发现其成核位置主要是在胶束和单体微珠滴里。此外,还发现SDS/St的质量比越大,相对分子质量越低。     

单分散P(St-BA-AN)/PANI核壳结构复合微球的制备与电性能

以苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为单体, 采用乳液聚合的方法制备出单分散苯乙烯-丙烯酸丁酯-丙烯腈三元共聚物[P(St-BA-AN)]种子微球, 再在该种子微球表面包覆聚苯胺(PANI), 制得P(St-BA-AN)/PANI核壳结构复合微球. 采用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外透射光谱(FTIR)和漫反射光谱等测试手段对所制备的种子微球和复合微球的形态、结构和形成机理进行了研究, 并用四探针法测定了核壳结构复合物的导电性. 研究结果表明, 通过改变种子乳液共聚物的组成和加入苯胺的量及氧化剂的量等条件可调控复合微球的电导率. 与P(St-BA)/PANI核壳结构复合微球相比, 在核组成中引入了氰基的P(St-BA-AN)/PANI核壳结构复合微球的电导率明显提高, 当加入苯胺的量为P(St-BA-AN)种子微球与苯胺单体总质量分数的40%时, 其电导率可达到0.71 S/cm. 红外光谱结果证实了P(St-BA-AN)种子微球中的氰基和壳层中聚苯胺的胺基之间存在某种相互作用, 导致核壳结构复合物电导率的提高.     

含氟丙烯酸酯三元共聚物乳液的研究

以丙烯酸全氟烷基酯 (ZonylTM)、甲基丙烯酸甲酯 (MMA)、丙烯酸丁酯 (BA)为原料 ,在阴离子乳化体系中制备了含氟丙烯酸三元共聚物乳液 .研究了聚合反应动力学、转化率的各种影响因素 ,得出了聚合速率方程 ,并得出反应的表观活化能 (Ea)为 5 0 75 8kJ mol.考察了乳液的稀释稳定性、贮存稳定性、离心稳定性、耐热、耐寒稳定性 ,及乳胶膜的吸水性和耐溶剂性 .并用Wilhelmy方法测定了乳胶膜与水的接触角 ,结果表明乳胶膜对水的抗浸润力大大提高     

Miniemulsion copolymerization of vinyl acetate and butyl acrylate. I. Differences between the miniemulsion copolymerization and the emulsion copolymerization processes

Differences between the emulsion copolymerization and miniemulsion copolymerization processes, in terms of emulsifier adsorption, emulsion stability, polymerization kinetics, copolymer composition and dynamic mechanical properties were studied for the comonomer mixture of 50:50 molar ratio vinyl acetate (VA+)—butyl acrylate (BuA), using sodium hexadecyl sulfate (SHS) as a surfactant and hexadecane (HD) as a co-surfactant. The use of hexadecane with the appropriate SHS initial concentration led to a higher adsorption of surfactant, smaller droplet size, higher stability of the emulsions, lower polymerization rates, and larger latex particle size. The copolymer composition during the initial 70% conversion was found to be less rich in Vac monomer units for the miniemulsion process. The dynamic mechanical properties of the copolymer films showed less mixing between the BuA-rich core and the VAc-rich shell in the miniemulsion latexes compared to the conventional latex films.     

偶氮型黄色共聚胶乳的合成与性能研究

聚合物乳液作为基本成膜物已在建筑涂料、木器漆和工业漆方面得到了广泛应用 .由于多数小分子染料与成膜物及其他组分的相容性不够好 ,常常导致这类彩色的聚合物产品涂刷时色泽不均、涂膜在使用过程中易于变色等缺陷 .将生色基团键合到聚合物分子链上 ,可以从根本上克服因相容性差而引起的染料小分子的迁移 ,同时还可以显著提高产品的保光保色性能[1] .1 986年 ,ＢＲＩＡＮ通过丙烯酸酯与含偶氮基烯类单体的乳液共聚合 ,制备出了一类可直接用于纺织印染行业的彩色乳液[2 ,3] .1 994年 ,ＳＯＳＮＯＷＳＫＩ等制备出了用于荧光标签的乳液聚合…     

光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。 通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。 结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1.25%时,乳胶膜具有较好的光致变色性能。     

A Study on the Vinyl Acetate-co-Butyl Acrylate Latexes in the Presence of N-Methylol Acrylamide and Mixed Type Emulsifiers

Summary: The properties of copolymer latexes depend on the copolymer composition, polymer morphology, initiator, polymerization medium and colloidal characteristics of copolymer particles. Poly(vinyl acetate-co-butyl acrylate) latexes with N-metylol acrylamide were prepared by applying semicontinuous emulsion polymerization. The systems studied were (a) the mixture of anionic sodium lauryl sulfate ether (SELES) with nonionic 30 moles ethoxylated nonyl phenol (NP 30) (50:50), (b) the mixture of anionic sodium lauryl sulfate ether (SELES) with nonionic 30 moles ethoxylated nonyl phenol (NP 30) (70:30), and (c) anionic sodium lauryl sulfate ether (SELES) (100%). The effects of the emulsifier and emulsifier composition on the physicochemical properties of obtained vinyl acetate-co-butyl acrylate latex properties in the presence of N-methylol acrylamide initiated by ammonium persulfate were investigated.     

STUDY ON THE POLYMERIZATION KINETICS AND STABILITY OF P(UA)/MMA MICROEMULSION*

 Urethane acrylate anionomer (APUA) as a kind of new type polymerizable emulsifier was synthesized using 2,4-toluene diisocyanate (TDI), polypropylene glycol (PPG), 2-hydroxyethyl methacrylate (HEMA) and dimethylolpropionic acid (DMPA). The critical micelle concentration (CMC) of APUA was measured by the methods of conductance and surface tension. The comparative studies between polymerizable emulsifier AUPA and conventional emulsifier sodium dodecyl sulfate (SDS) were carried out in the emulsion polymerization of methyl methacrylate (MMA). Polymerization kinetics,stability, size and morphology of the latex particles were investigated. It was found that in APUA both water soluble initiator potassium persulfate (KPS) and oil soluble initiator 2,2'-azobisisobutyronitrile (AIBN) can start the reaction of MMA, and the polymerization rate and yield were very high. On using AIBN as an initiator, the conversion-time behavior of MMA with APUA as emulsifier was different to that of SDS as emulsifier, signifying a different nucleation mechanism of the polymer latex particle. The average size of the two kinds of particles is about 50 nm. The particle size decreases with increasing emulsifier concentration. On using KPS as the initiator, APUA as emulsifier, cross-linking hydrogel of PMMA would be formed, but SDS was used as emulsifier and the hydrogel of PMMA was not present.     

含氟丙烯酸酯共聚乳液的制备及表征

采用十二烷基硫酸钠和壬基酚聚氧乙烯醚(OP-10)混合乳化剂，制备了粒径为40-50nm的甲基丙烯酸全氟辛基乙酯(FMA8)-甲基丙烯酸丁酯(BMA)-甲基丙烯酸(MA)共聚物乳液。通过DSC、、FTIR、^1H-NMR等手段对共聚物进行了表征。考察了乳液的稳定性、乳胶膜的吸水性和耐溶剂性以及全氟单体的含量对聚合反应的影响。     

Synthesis and characterization of covalently colored polymer latex based on new polymerizable anthraquinone dyes

Novel polymerizable red and yellow dyes, consisting of anthraquinone chromophore, alkyl spacer, and acryloyl group, were first synthesized and then used as comonomers in the semicontinuous emulsion copolymerization of styrene, butyl acrylate, and methacrylic acid to fabricate polymer latexes. The influences of the dye monomers on the emulsion polymerization process, the latex particle size and its distribution, the molecular weight of the latex polymer, as well as the light fastness of the polymer latex films, were investigated. Results indicated that, despite of the inhibition effect of the polymerizable dyes on polymerization, stable colored polymer latexes could be prepared with high conversion of total monomers, whereas the conversion of the polymerizable dye decreased as increasing the amount of dye. The light fastness of the covalently colored polymer latex films was proved to be much better than that of the noncovalently colored polymer latex films due to the covalent bond of dye and polymer chains.     

含氟/硅丙烯酸酯核壳型乳液的合成及性能

采用半连续种子乳液聚合法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 合成了以丙烯酸丁酯(BA)为核, 以甲基丙烯酸甲酯(MMA)、甲基丙烯酸十二氟庚酯(DFHMA)、3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPTMS)和甲基三甲氧基硅烷(MTMS)为壳的核壳型含氟/硅丙烯酸酯聚合物乳液. 利用FTIR, TEM, SEM-EDX和DSC等手段对乳液组成、乳胶粒子结构、膜表面及断面形态等进行了表征, 讨论了氟/硅含量对聚合物膜性能的影响. 结果表明, 核-壳粒子尺寸为20~30 nm, 乳液膜的性能与膜表面氟和硅的含量及相容性有较大的相关性, 当m(氟)∶m(硅单体)=3∶1时, 形成的膜均匀透明, 吸水率较低, 尺寸稳定性较好.     

Properties and characterization of novel cationic polyacrylate latex containing fluorine and silicon prepared with soap-free emulsion polymerization

The novel cationic polyacrylate latex containing fluorine silicon was successfully prepared via soap-free emulsion polymerization of butyl acrylate, methyl methacrylate, vinyltriethoxysilane and hexafluorobutylmethacrylate in water phase, which were initiated with water soluble azo initiator and emulsified with the mixed surfactants polymerizable emulsifier and OP-10. The films of the resultant latex were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and contact angle (CA) determinator, respectively. In comparison with the conventional polyacrylate latex, the thermal stability and water resistance of novel latex film are improved. The conditions of preparing the novel cationic acrylate latexes were optimized. The optimum conditions of preparing the novel latex are as follows: the amount of emulsifiers and the initiator are 6.0% and0.3%, respectively; both the amount of VETS and amount of HFMA are 6.0%. In this case, the conversion is high and the polymerization stability is good.