CO低温氧化Au/Al2O3催化剂的失活及稳定性

 采用改进的等体积浸渍法制备了1.5%Au/Al2O3催化剂,考察了催化剂在CO低温氧化反应中的催化活性,比较了其在干燥的原料气和水汽饱和的原料气中的稳定性,考察了经水汽饱和或加热的空气处理后催化剂活性的变化,探讨了催化剂失活的原因. 结果表明, Au/Al2O3在水汽饱和的原料气中比在干燥的原料气中具有更好的稳定性,经水汽饱和或加热的空气处理后其活性均会下降. Au/Al2O3的失活主要包括CO氧化失活、热处理失活和水汽处理失活,前两种失活主要是因为催化剂中类似碳酸盐物种的生成和活性位上-OH 的脱除,是可逆失活; 而最后一种失活是不可逆的,主要归因于金颗粒的长大.     

微乳法制备Au/Al2 O3 催化剂及其催化氧化CO性能的研究

用Tx-100／正己醇／环己烷／水的W／O微乳体系,合成了一系列Au／Al2O3催化剂。考察了焙烧温度、沉淀剂种类、搅拌方式等对Au／Al2O3,催化氧化CO活性的影响。结果表明：以氨水为沉淀剂,机械搅拌,600℃焙烧制得的Au／Al2O3,显示出较好的CO氧化性能。当反应温度为100℃时,CO转化率达85．0％,240℃时转化率达96．0％。XRD,DTA,TPR和TEM等表征表明：低温焙烧的催化剂,大部分载体Al2O3为无定型,对催化活性不利;焙烧温度过高,可能造成金微粒的团聚烧结,使其活性下降;由较强烈的搅拌方式制得的Au／Al2O3经适宜温度焙烧,可获得金粒尺寸较小、CO催化氧化活性较高的Au／γ-Al2O3催化剂。     

溶胶-凝胶法制备钯催化剂的织构与性能

采用溶胶-凝胶法制备了Pd/Al2O3催化剂，用LLS(激光光散射)、XRD和BET等技术考察了溶液pH值对所成胶体粒子流体力学半径、相应催化剂产品孔径分布及热稳定性的影响.研究发现，由pH=4.1的胶体制备的催化剂具有良好的热稳定性和CO、C3H6的氧化活性.氧化镧添加剂可抑制Al2O3载体在高温下由γ相向α相的转化，同时也促进了催化剂上Pd粒子的生长. La2O3可提高新鲜Pd催化剂的氧化活性，但对老化后催化剂活性的提高无促进作用.     

CO氧化反应中H2O对MOx和Au/MOx催化性能的影响

过渡金属氧化物［1,2］及负载型贵金属催化剂［3～13］是催化氧化消除CO的有效催化剂,一直是研究的热点. 虽然对MOx和Au/MOx上CO的氧化性能研究得较多,但大多是在无水条件下进行的;涉及催化剂抗水性能的报道较少［3,9,10］,且仅限于对催化剂活性的研究. Haruta等［3］对Au/Fe2O3,Au/Co3O4和Au/TiO 2等体系开展了一些工作, 认为水对CO氧化活性有促进作用. 本文重点考察了水对MOx(M=Al,Ca,Co,Cr,Cu,Fe,La,Mn,Ni和Zn)催化剂上CO氧化活性的影响,以及水对Au/MOx 催化剂活性及稳定性的影响.     

Ru-La_2O_3/γ-Al_2O_3催化剂合成、表征及CO选择氧化

采用浸渍法制备系列Ru-La2O3/γ-Al2O3复合氧化物催化剂,通过XRD、H2-TPR、CO-TPR、XPS、BET等方法对催化剂进行表征,考察La2O3的加入量、预处理方法对催化剂上CO选择氧化性能的影响.结果表明,110-170℃时Ru1La6/Al2O3催化剂上CO转化率达到99%以上,氧气利用率达55.7%以上.和Ru/Al2O3相比,Ru1La6/Al2O3催化剂在较低温度具有高活性,活性温度区间变宽.适量La2O3的加入促进了活性组分在载体表面分散,提高了催化剂的活性.经氢气预处理的Ru1La6/Al2O3催化剂活性最佳,催化剂上Ru物种结合能降低,表面钌物种活性位增多,且表面晶格氧浓度增大,更有利于CO气体在催化剂表面上的氧化反应.     

用辛烷基硫醇单层保护Au纳米粒子制备CO氧化催化剂Au/γ-Al2O3

采用两相法合成出含活性组分Au的辛烷基硫醇单层保护Au纳米粒子(C8AuNPs)的正己烷溶胶, 用“逐次浸润”法将C8AuNPs负载在γ-Al2O3上, 经真空干燥及活化处理制得Au/γ-Al2O3催化剂. 所制得的Au催化剂前体C8AuNPs/γ-Al2O3表面Au粒子平均粒径可控制在2-3 nm范围内, 且分布比较单一; 催化剂活性评价600 h后, 其表面Au的粒径仍主要分布在2-4 nm范围内; 真空干燥温度影响Au催化剂的粒子尺寸和催化活性, 随着真空干燥温度的提高, Au纳米粒子的粒径增大. 将所制备的催化剂用于低温CO氧化反应, 催化活性评价结果表明, 经25 ℃真空干燥制得的2.5%(质量分数, w)Au/γ-Al2O3具有较高的活性和长期稳定性, 其催化CO完全转化的最低温度为-19 ℃, 在15 ℃下CO完全转化时Au/γ-Al2O3的单程寿命至少900 h; 4.0%(w) Au/γ-Al2O3在15 ℃和进料中含水条件下对CO完全氧化的单程寿命不低于2000 h, 可见催化剂具有强的抗潮湿中毒特性. 综合上述实验结果, 讨论了影响Au/γ-Al2O3催化剂活性的可能因素.     

吸附柱色谱法制备负载型纳米金催化剂

采用吸附柱色谱新方法制备Au/AL2O3催化剂,并用于低温CO氧化反应,考察了Au盐溶液pH值及其与载体的液固比、载体比表面积和竞争吸附质等对Au催化剂性能的影响.结果表明,Au前驱体溶液的pH值为9,液崮比为6,优先吸附丙酮制得的催化剂Au颗粒大小分布均匀,粒径为5 nm左右,在-25℃即可实现CO完全转化.载体AL...     

Au/MOx/Al2O3催化剂催化CO低温氧化

 采用沉积沉淀法，将金负载在复合氧化物载体MOx/Al2O3上，制备得到了Au/MOx/Al2O3催化剂的活性要高于Au/Al2O3催化剂。Au/FeOx/Al2O3催化剂能够在低于223K的温度下实现CO完全催化氧化。TEM图象分析表明，纳米级高分散的金颗粒是金催化剂高活性的前提，但载体的选择，以及复合氧化物载体中过渡金属氧化物的选择，也会对金催化剂的活性产生明显的影响。     

Ru-La2O3/γ-Al2O3催化剂合成、表征及CO选择性氧化

采用浸渍法制备了系列Ru-La2O3/γ-Al2O3复合氧化物催化剂,考察了La2O3 的加入量、预处理方法对催化剂CO选择性氧化反应性能的影响,并通过XRD、H2-TPR、CO-TPR、XPS等手段对催化剂进行了表征。结果表明,添加La的 Ru1La6/Al2O3催化剂在110-170℃时具有99％以上的CO转化率,且催化剂的选择性在55.7%以上。和Ru/Al2O3相比,Ru1La6/Al2O3催化剂在较低温度下具有活性,活性温度区间变宽,适量La2O3的加入提高了钌物种的表面分散性,使催化剂表面活性位点增多,有利于CO的吸附和氧化,提高了催化剂的活性和选择性。和其他方法相比,经氢气预处理后的Ru1La6/Al2O3催化剂活性最佳,催化剂上Ru物种结合能降低,表面钌物种活性位增多,且表面晶格氧浓度增大,更有利于CO气体在催化剂表面上的氧化反应。     

高活性Co3O4负载单原子Au催化剂室温催化CO氧化

CO低温氧化是多相催化领域研究最多的反应之一.作为简单、典型的探针反应,其不仅具有重要的基础研究价值,而且在环境污染消除等方面也有着非常重要的实际应用价值.金属氧化物如铜锰(Hopcalite)、铜铬复合氧化物以及氧化钴等都具有优异的低温CO氧化活性.然而氧化物催化剂热稳定性低、反复启动性能差、以及对硫化物、水等物质敏感,严重制约了其实际应用.相对而言,负载型贵金属催化剂因具有较高的CO氧化活性、反应稳定性以及热稳定性而受到关注.但是贵金属价格昂贵、资源稀少,使其持续应用面临严峻挑战.为了提高贵金属利用效率、降低贵金属使用量,在负载型贵金属催化剂中,贵金属多以纳米尺度分散于高比表面载体上.由于多相催化一般在纳米粒子表面发生,只有表面金属原子能够接触到反应物,因而贵金属原子利用率仍然有待提高.最近本课题组成功开发以原子级分散的单原子催化剂并提出“单原子催化”的概念.后续研究以及其他研究人员相继证明氧化物负载贵金属单原子具有高活性和/或不同于纳米粒子的反应性能,表明开发单原子催化剂是最大化贵金属利用效率、降低贵金属用量的可行途径.对于CO氧化而言,目前普遍认为负载Au催化剂具有最高活性.然而负载Au单原子催化剂是否具有活性仍存争议：理论计算表明氧化物负载Au单原子催化剂具有很好的活性,但是缺少实验证据;目前已有一些氧化物负载Au正价离子催化剂的报道,结果也都表明Au单原子活性远低于纳米粒子或纳米团簇.最近本课题组发现氧化铁负载Au单原子不仅具有与Au纳米粒子相当的单位活性位(TOF)活性而且具有更高的单位金属重量(反应速率)活性以及非常高的反应稳定性.本文将载体拓展到氧化钴,开发了具有更高活性的氧化钴负载Au单原子催化剂, Au负载量仅为0.05 wt%即可在室温条件下实现CO完全转化. Co3O4载体用Co(NO3)3与Na2CO3通过共沉淀法制备,400 oC焙烧.然后通过简单的沉淀吸附法制备Co3O4负载Au单原子催化剂(Au1/Co3O4),确保Au单原子能够分散于载体的表面.具有原子分辨率的球差校正高分辨电镜照片显示Au原子确实以单原子形式分散于载体上.催化剂在第一个循环中活性并不非常高,但是在第二个循环中活性提高非常明显,可以在室温条件下实现CO全转化.为了弄清楚活性提高的原因,我们用惰性气体(He)、氧化性气体(5%O2/He)以及还原性气体(5%CO/He)对催化剂进行了热处理,但是活性提高并不明显.由此推断催化剂是在第一个循环反应过程中发生了某些变化,导致活性显著提高.空白载体实验表明Co3O4载体本身虽然具有反应活性,但是远不如负载少量Au原子活性高,表明Au原子或Au原子与载体一起起到高活性的作用.稳定性研究表明该催化剂在室温条件下容易失活,但经惰性气体或氧化气体处理后活性可恢复,表明不是结构性失活而是可逆失活,说明单原子非常稳定.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.