胆酸含量的近红外分析数学模型

本文应用近红外技术研究了快速测定胆酸含量的方法.通过测定胆酸在10000~4000cm-1范围内的近红外透射光谱,基于偏最小二乘(PLS)算法,建立了胆酸含量的数学模型.以校正均方差(RMSEC)和相关系数(R)为指标,确定了用于建模的最优近红外波段和光谱预处理方法,并基于此模型预测了9个样品.结果显示,建模效果良好,...     

近红外光谱法测定卷烟中多酚类物质含量的研究

利用烟草样品的近红外漫反射光谱,通过化学计量学的方法,建立了卷烟中多酚类物质的近红外数学模型.结果表明,绿原酸、新绿原酸和芸香苷近红外数学模型外部验证的平均相对误差和变异系数(RSD)均在5%以内,说明该模型准确性和稳定性均很好,可以用来快速、准确,无污染地测定卷烟中多酚类物质含量.     

近红外光谱法用于木薯燃料酒精品质分析

提出了用近红外光谱法测定木薯燃料酒精中乙醇和水分含量,以确定木薯燃料酒精的品质。结合修正偏最小二乘法建立了样品与其近红外光谱之间的定标模型。结果表明:乙醇定标模型交叉验证均方差和相关系数分别是0.110 2,0.960 5;水分定标模型分别是0.014 3,0.975 9。近红外光谱法预测值与化学分析法的测定值一致,该模型具有很高的预测准确性,可应用于木薯酒精品质分析的快速检测。     

近红外光谱法快速测定鲜木薯中淀粉含量

提出了用于现场快速测定鲜木薯中淀粉含量的近红外光谱法。取不同品种的鲜木薯样品90个,按国家标准方法(化学分析法)测得其淀粉含量。用近红外光谱法对此90个样品所制作的柱状样块的横截面进行光谱扫描,得其光谱图谱,并转换得到其一阶导数图。用CAUNIFT软件QPLS分析模块建立数学模型。结果表明:验证样品中淀粉的化学法测定值与近红外模型的预测值之间呈线性关系。用5份未知样品对所建模型进行外部验证,预测值与化学法测定值之间的绝对误差在2%以内,相对误差均小于5%。     

近红外光谱快速分析青贮饲料pH值和发酵产物

采用近红外光谱技术,结合偏最小二乘回归法,研究了142个不同种类的秸秆青贮饲料样品的pH值和发酵产物(乳酸、乙酸、丙酸、丁酸和氨态氮),建立了干燥粉碎和新鲜样品的近红外漫反射光谱定量分析模型以及浸提液样品的近红外透射光谱定量分析模型。研究发现,pH值的近红外漫反射光谱和透射光谱的分析效果均较好,校正模型决定系数R2和验证集样品预测值与化学值的相关关系决定系数r2都大于0.80,并且干燥粉碎、新鲜和浸提液样品的RPD值分别为3.44、2.50和2.27;3种状态样品的乳酸、乙酸、丁酸和氨态氮的定量分析模型精度需进一步提高;R2在0.64~0.85之间;RPD值在1.38~1.93之间;丙酸含量的测定结果较差。方差分析显示,3种状态样品的测定结果之间均无显著性差异(P>0.05)。     

近红外光谱法快速测定涂料固化剂中游离甲苯二异氰酸酯含量

用气相色谱分析值为参照,采用近红外透射光谱（NIR）技术采集相应样品的NIR光谱,研究了涂料固化剂中游离甲苯二异氰酸酯（TDI）含量的快速测定分析方法。 并从120个固化剂样品中挑选出109个代表性的样品建模,选择7320~7250 cm-1和8485~8370 cm-1波段区间,用偏最小二乘法(PLS)和完全交互验证方式建立TDI含量的预测模型。 结果表明,固化剂中游离甲苯二异氰酸酯含量和近红外光谱之间存在较好的相关性,其预测模型的校正集均方差（RMSEC）为0.0815,验证集均方差（RMSEP）为0.0715,模型性能良好。 近红外光谱法可快速准确测定游离甲苯二异氰酸酯（TDI）含量,用于固化剂样品快速分析。     

近红外光谱技术定量分析连作滁菊土壤中的阿魏酸含量

应用近红外光谱(NIRS)技术定量分析连作滁菊土壤样品中阿魏酸的含量.通过标准杠杆值、学生残差和马氏距离判断异常光谱,经二阶导数和Norris平滑滤噪预处理后,在6000~4000 cm-1范围,最佳因子数为7,采用偏最小二乘法(PLS)构建数学模型.结果表明,模型校正集和验证集与高效液相色谱仪(HPLC)测定的参考值之间均呈现良好相关关系,校正相关系数Rc为0.9914,交叉验证相关系数Rcv为0.9935,校正集误差均方根(RMSEC)为0.484,预测误差均方根(RMSEP)为0.539,交叉验证误差均方根(RMSECV)为0.615.研究结果表明,NIRS分析技术能够实现连作土壤中阿魏酸的快速检测,结果准确可靠.     

傅里叶变换近红外光谱法快速检测人血清生化成分

应用傅里叶变换近红外光谱透射技术结合偏最小二乘法(PLS)建立了人血清中7种生化成分的定标模型,利用内部交叉验证和自动优化功能对定标模型进行了优化,确定了最优建模参数。模型对人血清中总胆固醇、甘油三酯、总蛋白、白蛋白、载脂蛋白B、低密度脂蛋白胆固醇、葡萄糖定标样品集的预测值与化学值的相关系数r分别为0.9011、0.9593、0.9249、0.761、0.8831、0.5191、0 9148,预测校正标准误差RMSECV分别为15mg/dL,21.6mg/dL,2 66g/L,3 96g/L,0.091g/L,16.2mg/dL,0.49mmol/L。     

近红外光谱与组合的间隔偏最小二乘法测定清开灵四混液中总氮和栀子苷的含量

应用近红外光谱分析技术结合化学计量学方法, 建立了中药清开灵注射液中间体总氮和栀子苷含量测定的新方法. 首先采用Kernard-Stone法对训练集样本和预测集样品进行分类, 然后应用组合的间隔偏最小二乘法(Synergy interval partial least squares, siPLS)对所得近红外透射光谱进行有效谱段范围的选择以及二者定量校正模型的建立, 并对光谱预处理方法进行了详细的讨论. 所建立的总氮和栀子苷校正模型的预测相关系数(R)分别为0.999和0.708; 交叉验证误差均方根(RMSECV)均为0.023; 预测误差均方根(RMSEP)分别为0.074和0.159; 预测结果表明, 本实验所建方法快速、无损且可靠, 可推广并应用于中药注射液中间体的在线质量控制.     

短波近红外光谱法对蛇床子SFE萃取产物的定量分析

利用中药蛇床子CO2超临界萃取(SFE)的萃取物的短波近红外漫反射光谱(800～1100 nm),以HPLC分析值作参比值,采用化学计量学中的偏最小二乘法(PLS)建立短波近红外漫反射光谱与蛇床子SFE萃取物中主要成分蛇床子素和欧前胡素间定量分析数学模型.实现了快速、无损的测定双组分中药的有效成分.讨论了光谱的预处理方法和主成分数对PLS定量预测蛇床子萃取物中蛇床子素和欧前胡素含量能力的影响,并对预测集样品进行预测.     

Determination of amylose in Iranian rice by multivariate calibration of the surface plasmon resonance spectra of silver nanoparticles

A simple and non-separative analytical method for selective determination of amylose in Iranian rice has been developed. It was based on the reduction of silver ions by amylose and production of Ag nanoparticles, which exhibit surface plasmon resonance (SPR) spectra in the ultraviolet/visible region. The formation of Ag nanoparticles in the presence of amylose was monitored by transmission electron microscopy (TEM) and dynamic light scattering (DLS). The experimental conditions were optimized to obtain the highest yield for nanoparticle formation. Partial least square (PLS) regression as an efficient multivariate spectral calibration method was employed to make a connection between the SPR spectra of the generated Ag nanoparticles and the amylose content (AC) of the rice starch. The number of PLS latent variables was optimized by leave-one-out cross-validation utilizing prediction residual error sum of square (PRESS). The proposed model exhibited a high ability for prediction of amylose concentration in both standard starch samples and real rice samples prepared from different regions of Iran. The relative errors of prediction were almost lower than ±5% for different real samples and the detection limit was 3.23 weight percent of amylose in rice. In comparison to the reference method (Juliano method), the proposed method is simpler and does not need tedious sample preprocessing steps.     

Exact mass measurements using a 7 tesla fourier transform ion cyclotron resonance mass spectrometer in a good laboratory practices-regulated environment

Fourier transform ion cyclotron resonance mass spectrometry has been found to produce reliable exact mass measurements using two different internal calibration methods. For these measurements, electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI) were utilized both individually and in tandem. For internal calibration with a co-dissolved polyethylene glycol standard, measurements of 41 compounds resulted in an average absolute mass determination error of 0.7 ppm, with a standard deviation of 0.9 ppm. For comparison, internal calibration was effected through the simultaneous use of ESI and MALDI, with the former being used for the introduction of analyte ions and the latter for formation of polymethylmethacrylate calibrant ions. This technique led to mass measurements with an average absolute error of 0.8 ppm and a standard deviation of 1.0 ppm. In addition, exact mass measurements of tandem mass spectrometry fragment ions were made for 35 compounds using external calibration with a single internal mass standard. The observed average absolute error was 0.7 ppm with a standard deviation of 1.0 ppm.     

Application of transmission near-infrared spectroscopy to uniformity of content testing of intact steroid tablets

Transmission near-infrared (NIR) spectroscopy was used for the rapid and non-destructive determination of the content of a hormone steroid in single intact tablets. Tablets produced for clinical trial purposes containing 5, 10, 15, 20 and 30 mg (2.94, 5.88, 8.82, 11.76 and 17.64% m/m, respectively) were used to develop calibration models without the need to specially prepare any out of specification tablets. Reference values for the individual tablets used in the NIR calibration models and test set were measured by reversed-phase high performance liquid chromatography (HPLC). Partial least squares regression using standard normal variate transformed second-derivative spectra over the range 800 to 1040 nm gave the optimum calibration model with a standard error of calibration of 0.52 mg per tablet. Measurements of an independent test set gave comparable results (standard error of prediction 0.31 mg per tablet). Measurement errors for a single tablet (RSD < 2.5% for a given active level) were sufficiently small to allow the procedure to be applied to pharmacopoeial uniformity of content testing of batches of these tablets and permitted the non-destructive testing of 30 tablets in under 20 min as compared to 6 h by HPLC.     

Experimental Considerations for Temperature Modulated DSC at Low Temperature

Temperature modulated DSC (TMDSC) at low temperatures requires attention to the selection of experimental parameters that are within the capability of the instrumentation as well as special care in calibration of heat capacity measurement when high precision is required. Data are presented to facilitate selection of appropriate modulation periods and amplitudes at low temperature when using a mechanical cooling accessory. The standard error of the mean heat capacity measurement for a sapphire standard increased with decreasing temperature, decreasing period, and increasing pan mass. For ice in hermetically sealed pans, the standard error of the mean heat capacity measurement was larger than for sapphire and did not follow a predictable trend with changes in temperature and period of modulation. This was attributed to changes in sample geometry between successive measurements due to melting and resolidification. A simple one-point temperature calibration by TMDSC may be unsuitable for precise measurement of heat capacity because of the random error caused by sample placement and the systematic error caused by cell asymmetry, temperature dependence of the calibration constant, and different sample thermal conductivities. An alternative calibration procedure using standard DSC and either a linear or second order fit of the calibration constant over the temperature range of interest is proposed. This revised version was published online in August 2006 with corrections to the Cover Date.     

独立分量分析预处理法提高苹果糖度模型预测精度研究

为了提高苹果近红外光谱糖度预测模型精度,利用独立分量分析方法(ICA)对苹果近红外光谱进行了预处理,并且建立了糖度的偏最小二乘(PLS)预测模型。结果表明,独立分量分析不但能分离出噪声信号,而且所分离出来的光谱信号也比原始光谱信号光滑。在预处理后的最佳PLS糖度模型校正时的相关系数rc和标准偏差SEC分别为0.9549和0.3361,用于预测时的相关系数rp和标准偏差SEP分别为0.9071和0.4355。与普通的平均处理法的PLS模型相比,其精度有所提高,且模型更加简洁。     

Estimation of the standard uncertainty of a calibration curve: application to sulfur mass concentration determination in fuels

The construction of a calibration curve using least square linear regression is common in many analytical measurements, and it comprises an important uncertainty component of the whole analytical procedure uncertainty. In the present work, various methodologies are applied concerning the estimation of the standard uncertainty of a calibration curve used for the determination of sulfur mass concentration in fuels. The methodologies applied include the GUM uncertainty framework, the Kragten numerical method, the Monte Carlo method (MCM) as well as the approximate equation calculating the standard error of prediction. The standard uncertainty results obtained by all methodologies agree well (0.172?C0.175?ng???L^?1). Aspects of inappropriate use of the approximate equation of the standard error of prediction, which leads to overestimation or underestimation of calculated uncertainty, are discussed. Moreover, the importance of the correlation between calibration curve parameters (slope and intercept) within GUM, MCM and Kragten approaches is examined.     

Determination of thiamine HCl and pyridoxine HCl in pharmaceutical preparations using UV-visible spectrophotometry and genetic algorithm based multivariate calibration methods

Simultaneous determination of binary mixtures pyridoxine hydrochloride and thiamine hydrochloride in a vitamin combination using UV-visible spectrophotometry and classical least squares (CLS) and three newly developed genetic algorithm (GA) based multivariate calibration methods was demonstrated. The three genetic multivariate calibration methods are Genetic Classical Least Squares (GCLS), Genetic Inverse Least Squares (GILS) and Genetic Regression (GR). The sample data set contains the UV-visible spectra of 30 synthetic mixtures (8 to 40 microg/ml) of these vitamins and 10 tablets containing 250 mg from each vitamin. The spectra cover the range from 200 to 330 nm in 0.1 nm intervals. Several calibration models were built with the four methods for the two components. Overall, the standard error of calibration (SEC) and the standard error of prediction (SEP) for the synthetic data were in the range of <0.01 and 0.43 microg/ml for all the four methods. The SEP values for the tablets were in the range of 2.91 and 11.51 mg/tablets. A comparison of genetic algorithm selected wavelengths for each component using GR method was also included.     

The uncertainty of a result from a linear calibration

The standard error of a result obtained from a straight line calibration is given by a well known ISO-endorsed expression. Its derivation and use are explained and the approach is extended for any function that is linear in the coefficients, with an example of a weighted quadratic calibration in ICPAES. When calculating the standard error of an estimate, if QC data is available it is recommended to use the repeatability of the instrumental response, rather than the standard error of the regression, in the equation.     

Analysis of grass silage from Northwestern Spain by near-infrared reflectance spectroscopy

Near-infrared reflectance spectroscopy (NIRS) was evaluated for the determination of protein, crude fiber (CF), acid detergent fiber (ADF), and neutral detergent fiber (NDF) in grass silage. Calibration equations were based on analyses of 366 samples of grass silage produced in Northwestern Spain over 4 consecutive years (1992-1995) and validated by analyses of a set of 72 silage samples harvested during 1996. Dried and ground samples were analyzed by chemical and NIRS procedures. The spectral data were analyzed by regression against a range of chemical parameters, using modified partial least-squares (MPLS) multivariate analysis in conjunction with different mathematical treatments of the spectra. For each parameter, the optimum calibration was evaluated on the basis of the coefficient of multiple determination (R2), the coefficient of simple correlation (r2), the standard error of calibration (SEC), the standard error of cross-validation (SECV), and the standard error of validation (SEV). R2 and r2 were >0.90; SEC values were 0.58, 1.04, 1.40, and 1.75; SECV values were 0.64,1.15,1.50, and 2.04; and SEV values were 0.56,1.02, 1.42, and 1.80 for protein, CF, ADF, and NDF, respectively. The ratio of the standard deviation of the reference data to the SEV was >3.0 for each of the 4 parameters, which indicates that the equations can be used in routine analysis.     

Screening Inorganic Arsenic in Rice by Visible and Near-Infrared Spectroscopy

The potential of near-infrared spectroscopy (NIRS) for screening the inorganic arsenic (i-As) content in commercial rice was assessed. Forty samples of rice were freeze-dried and scanned by NIRS. The i-As contents of the samples were obtained by acid digestion-solvent extraction followed by hydride generation atomic absorption spectrometry, and were regressed against different spectral transformations by modified partial least square (MPLS) regression. The second derivative transformation equation of the raw optical data, previously standardized by applying standard normal variate (SNV) and De-trending (DT) algorithms, resulted in a coefficient of determination in the cross-validation (1-VR) of 0.65, indicative of equations useful for correct separation of the samples in low, medium and high groups. The standard deviation (SD) to standard error of cross-validation (SECV) ratio, expressed in the second derivative equation, was similar to those obtained for other trace metal calibrations reported in NIRS reflectance. Spectral information relating to starch, lipids and fiber in the rice grain, and also pigments in the caryopsis, were the main components used by MPLS for modeling the selected prediction equation. This pioneering use of NIRS to predict the i-As content in rice represents an important reduction in labor input and cost of analysis.