Broad gain,continuous-wave operation of InP-based quantum cascade laser at λ~11.8 μm

We demonstrate a broad gain, continuous-wave (CW) operation InP-based quantum cascade laser (QCL) emitting at 11.8 μm with a modified dual-upper-state (DAU) and diagonal transition active region design. A 3 mm cavity length, 16.5 μm average ridge wide QCL with high-reflection (HR) coatings demonstrates a maximum peak power of 1.07 W at 283 K and CW output power of 60 mW at 293 K. The device also shows a broad and dual-frequency lasing spectrum in pulsed mode and a maximum average power of 258.6 mW at 283 K. Moreover, the full width at half maximum (FWHM) of the electroluminescent spectrum measured at subthreshold current is 2.37 μm, which indicates a broad gain spectrum of the materials. The tuning range of 1.38 μm is obtained by a grating-coupled external cavity (EC) Littrow configuration, which is beneficial for gas detection.     

Laser diode-array pumped Nd:YAlO_3 CW laser at 1079.5nm and 1341.4nm

Two key problems,spectral matching and spatial overlap between pumpingbeam and the laser mode in the active material,of diode-laser-arrays(LD)end-pumped solid-state laser have been discussed.Initial experimental results were given for LD end-pumpedTEM_(00) CW Nd:YAlO_3 laser at the wavelength of 1079.5nm and 1341.4nm.The outputpower at 1079.5nm is 24.4mW with 14.5％ slope efficiency,and the output power is 1.2mW at 1341.4nm.     

Performance of a diode end-pumped Cr,Er:YSGG laser at 2.79 μm

We present a diode end-pumped Cr,Er:YSGG laser at 2.79 μm operated in the continuous-wave (CW) and pulsed modes. Er³⁺ ions are directly pumped into the upper laser state ⁴ I _11/2 using a 967-nm diode laser, which avoids various nonradiative losses. The laser produces 50.2 mW of power in the CW mode. An average power of 169 mW is obtained at a repetition rate of 100 Hz and a pulse duration of 2 ms. The maximum laser energy achieved is 1.95 mJ at a repetition rate of 50 Hz, corresponding to a peak power of 970 mW and a slope efficiency is 7.6%. The far-field divergence angle of the laser is measured to be 8 mrad.     

基于多层石墨烯可饱和吸收体的被动调Q Ho∶YAG激光器

报道了2μm被动调Q的Ho∶YAG激光器,该激光器采用Tm~(3+)光纤激光器作为泵浦源,使用多层石墨烯作为可饱和吸收体。在连续波激光输出模式下,当泵浦功率为4.2 W时,获得了750 mW激光输出,输出激光中心波长为2.09μm,斜率效率为29.6%。在连续波激光器谐振腔中插入多层石墨烯可饱和吸收体并调整谐振腔,获得了脉冲激光输出。当泵浦功率为4.2 W时,获得最小脉冲宽度3.1μs、重复频率66.6 kHz的脉冲激光输出,其最大平均输出功率为170 mW,斜率效率为12.6%,光束质量因子M_x~2=1.15,M_y~2=1.12。     

Low-threshold interband cascade lasers operating above room temperature

Mid-IR type-II interband cascade lasers were demonstrated in pulsed mode at temperatures up to 325 K and in continuous mode up to 200 K. At 80 K, the threshold current density was 8.9 A/cm² and a continuous wave output power of 140 mW/facet was obtained.     

Diode-pumped laser performance of Tm:Sc_2SiO_5 crystal at 1971 nm

The 4-at.% Tm:Sc_2SiO_5 (Tm:SSO) crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave(CW) laser output of(100)-cut Tm:SSO with the dimensions of 3 mm×3 mm×3 mm under laser diode(LD)-pumping is realized. The full width at half maximum(FWHM) of the laser emitting reaches up to 21 nm. The laser threshold of Tm:SSO is measured to be 0.43 W. Efficient diode-pumped CW laser performance of Tm:SSO is demonstrated with a slope efficiency of 25.9% and maximum output power of 934 mW.     

NdKYW新型全固体激光器研究

报道了采用半导体二极管抽运的掺钕钨酸钇钾［Nd3+KY(WO4)2］(简称NdKYW)蓝绿光激光器。腔内倍频采用了Ⅰ类临界相位匹配LBO(LiB3O5)晶体作为倍频器,阈值抽运功率为400 mW,在抽运功率为2 W时获得了200 mW的530 nm连续激光输出,其倍频光的光-光转换效率为10%。     

High-power and high-temperature THz quantum-cascade lasers based on lens-coupled metal-metal waveguides

A metal-metal waveguide quantum cascade laser with an abutted silicon hyperhemispherical lens is demonstrated at ~4.1 THz. The device produced 145 mW of peak pulsed power at 5 K with a wall-plug power efficiency of 0.7%, lasing up to a maximum operating temperature of 160 K. The far-field beam pattern has a full width at half-maximum value of ~4.8 degrees in the H plane. The same device produced ~26 mW of peak power using a Winston cone instead of a lens, lasing up to 165 K. The large increase in output power is mainly attributed to an increase in collection efficiency.     

High-performance,continuous-wave quantum-cascade lasers operating up to 85°C at <Emphasis Type="Italic">λ</Emphasis>∼8.8 μm

High-temperature, high-power, and continuous-wave (CW) operation of quantum-cascade lasers with 35 active/injector stages at λ∼8.85 μm above room temperature is achieved without using a buried heterostructure. At this long wavelength, the use of a wider ridge waveguide in an epilayer-down bonding scheme leads to a superior performance of the laser. For a high-reflectivity-coated 21 μm×3 mm laser, the output power of 237 mW and the threshold current density of 1.44 kA/cm² at 298 K under CW mode are obtained with a maximum wall-plug efficiency of 1.7%. Further improvements were observed by using a 4-mm-long cavity. The device exhibits 294 mW of output power at 298 K and it operates at a high temperature, even up to 358 K (85°C). The full widths at half-maximum of the laser beam in CW operation for the parallel and the perpendicular far-field patterns are 25°and 63°, respectively.     

Studies on the SFD Properties of Nd_xGd_(1-x)Ca_4O(BO_3)_3 Solid-solution Crystal

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｔｈｅｐａｓｔｆｅｗｙｅａｒｓ,ｓｍａｌｌｓｉｚｅｄＳＦＤｌａｓｅｒｈａｓａｔｔｒａｃｔｅｄｇｒｅａｔａｔｔｅｎｔｉｏｎｓ.Ｌａｓｅｒｄｉｏｄｅ(ＬＤ)ｐｕｍｐｅｄｓｏｌｉｄｓｔａｔｅｌａｓｅｒｓｈａｖｅｂｅｅｎｆｏｕｎｄｖｅｒｙｕｓｅｆｕｌｉｎｔｈｅｆｉｅｌｄｓｏｆｍｉｌｉｔａｒｙ,ｉｎｄｕｓｔｒｙ,ｍｅｄｉｃａｌｔｒｅａｔｍｅｎｔａｎｄｓｃｉｅｎｔｉｆｉｃｒｅｓｅａｒｃｈｅｓｄｕｅｔｏｔｈｅａｄｖａｎｔａｇｅｓｏｆｈｉｇｈｓｔａｂｉｌｉｔｙ,ｃｏｍｐａｃｔｎｅｓｓ…     

半导体泵浦铷蒸气激光器国内首次出光北大核心CSCD

采用体光栅对商用线阵半导体激光器进行线宽压缩,得到线宽0.1nm、中心波长780.2nm、最高连续输出功率80W的泵浦激光输出。为了降低热效应,通过外加斩波器将泵浦光转化为脉冲模式,脉宽440μs,占空比为1∶5。采用长度为5mm的铷金属饱和蒸气作为增益介质,并在常温下充入33kPa乙烷和47kPa氦气,进行了出光实验。在泵浦峰值功率35.4W,铷吸收池温度120℃时,得到峰值功率600mW的795nm铷激光输出,斜率效率为1.7%。     

Studies on the SFD Properties of NdxGd1-xCa4O(BO3)3 Solid-solution Crystal

NdxGd1-xCa4O(BO3)3 (NdGdCOB) is a new self-frequency-doubling (SFD) solid-solution crystal. The second-harmonic generation (SHG) phase-matching (PM) curves were calculated by using refractive indices. The deff of NdGdCOB crystal along different PM directions were calculated according to the sellmeier equation and dijk data in which the (θ=66.8°, φ=132.6°) PM direction has the highest deff. SFD experiments were carried out with Ti:sapphire CW laser and pulsed dye-laser. A green laser output power up to 225 mW at 530 nm was achieved from a 7×3×3 mm3 crystal sample pumped by 1560 mW CW Ti:sapphire laser. The lasing threshold of SFD was lower than 1.8 mW along the PM direction (66.8°,132.6°). The optical-optical conversion efficiency was 14.4%. The conversion efficiency was 7.7% when 10×3×3 mm3 sample was side-pumped by the pulsed dye-laser tuned to 595.4 nm with 17.5 mJ energy and the lasing threshold is 1.2 mJ.     

连续锁模Nd：YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd:YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 W LD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值（35 mW）和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W时获得了210 mW的平均输出功率.     

连续锁模Nd∶YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd∶YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 WLD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值(35 mW)和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W 时获得了210 mW的平均输出功率.     

A low-threshold and high-power oxide-confined 850-nm AlInGaAs strained quantum-well vertical-cavity surface-emitting laser

A low-threshold and high-power oxide-confined 850-nm AlInGaAs strained quantum-well (QW) vertical-cavity surface-emitting laser (VCSEL) based on an intra-cavity contacted structure is fabricated. A threshold current of 1.5 mA for a 22 μm oxide aperture device is achieved, which corresponds to a threshold current density of 0.395 kA/cm². The peak output optical power reaches 17.5 mW at an injection current of 30 mA at room temperature under pulsed operation. While under continuous-wave (CW) operation, the maximum power attains 10.5 mW. Such a device demonstrates a high characteristic temperature of 327 K within a temperature range from -12℃ to 96℃ and good reliability under a lifetime test. There is almost no decrease of the optical power when the device operates at a current of 5 mA at room temperature under the CW injection current.     

Narrow linewidth continuous-wave and gain-switched fiber laser with intracavity unpumped Er-doped fiber loop

Investigation has been performed for the characteristics of the fiber ring laser incorporating an intracavity unpumped Er-doped fiber Sagnac loop for narrow linewidth continuous wave (CW) and gain-switched pulsed operation. The gain-switched pulse has duty cycle of 4.4% with more than 113 mW in peak power at the reflective optical filter output and the laser was stable both in output power and the peak wavelength.     

全固态Cr:LiSAF激光器的研究

本文报道了红光激光二极管泵浦的Cr:LiSAF激光器.采用纵向泵浦的平凹腔结构,在脉冲方式泵浦下,当泵浦平均功率为54mW,重复频率为200Hz时得到平均功率为5mW的激光输出,在连续波状态下,测得了输出功率随泵浦功率的变化曲线.激光输出的中心波长为873nm.     

2041.3 nm/2054.6 nm simultaneous dual-wavelength single-longitudinal-mode Tm,Ho:YVO<Subscript>4</Subscript> microchip laser

We report a single-longitudinal-mode CW diode-pumped Tm, Ho: YVO₄ microchip laser emitting at both 2041.3 and 2054.6 nm. At each wavelength, the laser has a single longitudinal mode. The total single-longitudinal-mode output power reaches 185 mW with 20.4% optical conversion efficiency at 905 mW incident pump power.     

Blue laser light generation by intracavity frequency doubling of Cesium vapor laser

Blue laser light with a wavelength 447 nm was generated by intracavity frequency doubling of a Cs laser in PPKTP crystal. A continuous wave power of 600 mW was obtained at an optical-to-optical efficiency of 4%. In the pulsed operation, when thermal effects were reduced, the efficiency obtained was 14% and the peak blue power was 2.1 W.     

Theoretical and Experimental Investigations of Diode-Pumped Tm:YAG Laser in Active Mirror Configuration

Based on the rate-equations of quasi-three-level lasers, we analyzed the threshold and the output power of longitudinally pumped Tm:YAG lasers in an active mirror configuration. In contrast to one-pass pumping, two-pass pumping in this configuration will result in a 24% decrease in threshold and 16% increase in slope efficiency. Using a 3-W diode-laser pumping in the active mirror configuration, we demonstrated a CW Tm:YAG laser and obtained 735 mW output power with a slope efficiency up to 49%. Using a Ti:sapphire laser to pump the same device, the threshold power was further reduced and the slope efficiency reached 59%.