酸碱处理后纳米微晶纤维素的热行为分析

Nanocrystalline cellulose (NCC) was prepared from microcrystalline cellulose (MCC) by acid hydrolysis. It was observed that the diameter of NCC particles mainly distributed over 30-50nm by transmission electron microscope (TEM) . The crystal form and degree of crystallinity were detected by X-Ray diffraction. The results showed that NCC and MCC have the same crystal form of cellulose I, and that the reactions mainly occurred in the amorphous region of MCC during the acid hydrolysis process. The thermal behavior of NCC in different pH conditions was characterized by differential scanning calorimetry (DSC) . The consequences indicate that the thermal stability of NCC distinctly decreased by contrast with the thermal stability of MCC, and that the thermal stability of NCCs in alkali conditions was higher than that of NCCs in acid conditions. The specific surface area distinctly increased with sharp decreasing of the particle size of NCC. This induced the end carbons and active groups of surface of NCC to increase sharply, therefore caused the thermal stability of NCC to distinctly abate. That NCC has very strong adsorption affinity is the cause of the obvious difference of thermal behavior of NCC in different pH. In acid conditions the surface of NCC adsorbed a great lot of H^ , which induced the cellulose chains of surface of NCC to decompose at low temperature catalyzed by H^ . When adding sodium hydroxide solution, on one hand the H^ of surface of NCC was neutralized; on the other hand, the cellulose chains of low molecular weight were dissolved in sodium hydroxide solution and the defects of surface of NCC rearranged and stable structure formed. These factors improved the thermal stability of NCC in alkali conditions.     

CHARACTERIZATION OF REGENERATED CELLULOSE MEMBRANES HYDROLYZED FROM CELLULOSE ACETATE

A series of cellulose acetate membranes were prepared by using formamide as additive, and then were hydrolyzedin 4 wt% aqueous NaOH solution for 8 h to obtain regenerated cellulose membranes. The dependence of degree ofsubstitution, structure, porous properties, solubility and thermal stability on hydrolysis time was studied by chemical titration,Fourier transform infrared spectroscopy, scanning electron microscopy, wide-angle X-ray diffraction, and differentialscanning calorimetry, respectively. The results indicated that the pore size of the regenerated cellulose membranes wasslightly smaller than that of cellulose acetate membrane, while solvent-resistance, crystallinity and thermostability weresignificantly improved. This work provides a simple way to prepare the porous cellulose membranes, which not only kept thegood pore characteristics of cellulose acetate membranes, but also possessed solvent-resistance, high crystallinity andthermostability. Therefore, the application range ofcellulose acetate membranes can be expanded.     

REFRACTOMETRY AND TEXTURES OF METHYL-CYANOETHYL CELLULOSE/DICHLOROACETIC ACID LIQUID CRYSTA LLI NE SOLUTIONS~+

An Abbe refractometer with a rotatable polarizer mounted on the eyepiece is used for determining the two principal refractive indices of methyl-cyanoethyl cellulose/dichloroacetic acid liquid crystalline solutions. The critical concentration where the mesophase appears can be determined according to the variation of the increment of the refractive index with the concentration. Mesophase textures of the liquid crystalline solutions are observed and the influence of the concentration on mesophase textures is also discussed.     

纤维素催化转化为高附加值化学品的研究进展

Currently,under huge pressure from energy demands and environmental problems,much attention is being paid to biomass conversion,which will play an important role in meeting the requirements for a sustainable society.As the most abundant biomass on earth, cellulose is usually used as the first research target for biomass conversion.In this review,the recalcitrant structure of cellulose is discussed and non-catalytic hydrolysis by hot-compressed water and catalytic hydrolysis using solid acids are then considered.We also review the catalytic conversion of cellulose into valuable chemicals including hexitols(sorbitol and mannitol),ethylene glycol,and related compounds using various heterogeneous catalysts.     

BIODEGRADATION OF REGENERATED CELLULOSE FILMS BY FUNGI

The biodegradability of Aspergillus niger (A. niger), Mucor (M-305) and Trichoderma(T-311) strains on regenerated cellulose films in media was investigated. The results showedthat T-311 strain isolated from soil adhered on the cellulose film fragments has strongerdegradation effect on the cellulose film than A. niger strain. The weights, molecular weightsand tensile strengths of the cellulose films in both shake culture and solid media decreasedwith incubation time, accompanied by producing CO_2 and saccharides. HPLC, IR and re-leased CO_2 analysis indicated that the biodegradation products of the regenerated cellulosefilms mainly contain oligosaccharides, cellobiose, glucose, arabinose, erythrose, glycerose,glycerol, ethanal, formaldehyde and organic acid, the end products were CO_2 and water.After a month, the films were completely decomposed by fungi in the media at 30℃.     

STUDIES ON IMMOBILIZED GLUCOSE OXIDASE BY DIETHYLAMINOETHYL CELLULOSE COMPLEXES

The properties of immobilized glucose oxidase (GOD) by the complexes of diethylaminoethyl cellulose(DEAEC) with different polymers, such as polymethylacrylic acid (PMAA), polyacrylic acid (PAA), polystyrene sulfonic acid (PSSA), polyvinylaleohol (PVA), polyethylene oxide (PEO) and styrene-maleic acid copolymer (PSMA) were investigated. The activity of immobilized GOD was obviously influenced by the component of the DEAEC complexes. The relative activity of the immobilized GOD reached to maximum and over 90% of the native GOD. when the DEAEC-PMAA DEAEC-PAA complexes were used as a carrier with the molar ratio of DEAEC and polyacid of about one. Michaelis constants (Km) of the immobilized enzymes of DEAEC-GOD-PMAA and DEAEC-GOD-PAA were determined to be 1.25 and 1.00, respectively. Moreover, the immobilized GOD has a good storage stability and cyclic life.     

超声化学制备单分散金属纳米钯

A simple sonochemical technique is used to synthesize palladium nanoparticles in a poly(ethylene glycol) (PEG) solvent at room temperature. The reaction based on chemical reduction of PdCl₂ by ascorbic acid (AA). The as prepared Pd nanoparticles are highly dispersed and uniform in size (with average size of ～20nm). The products were characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM).     

萘与丙烯在脱铝丝光沸石上的烷基化反应

Shape selective alkylation of polynuclear aromatics has begun to receive increasing attention. 2,6 dialkylnaphthalenes are important raw materials for manufacturing high quality polyester fibers and plastics. Understanding of the reaction and the catalysis for conversion of polycyclic aromatic hydrocarbons is needed both from fundamental and practical view points. In this paper, alkylation of naphthalene with propene over a series of dealuminated mordenite with different Si/Al ratios was carried out in an autoclave with an electromagnetical stirrer. Textural property of the dealuminated mordenite was determined by nitrogen adsorption. The amount of the acid sites was measured by NH 3 TPD. The catalytic activity of HM and β shape selectivity for products increased with increasing the Si/Al ratio in HM. Moreover, the selectivity for alkylation with propene was also increased by dealumination treatment. The increase of the catalytic activity was attributed to the formation of mesopores, which significantly promoted the diffusion of reactants and products in mordenite. It was suggested that the increase of β selectivity resulted from the elimination of acid sites from the external surface, and the selectivity for alkylation with propene was improved owing to the creation of the interconnection between 12 ring and 8 rimg channels by dealumination.     

STRUCTURE AND PROPERTIES OF P(MMA-MAA)/PEO INTERMACROMOLECULAR COMPLEX FORMED THROUGH HYDROGEN BONDING

The superstructure and properties of polymers might be improved and enhanced througl intermolecular complexation. In this paper, the preparation, structure and properties of P(MMA-MAA)/PEO intermolecular complex through hydrogen bonding are studied. By acid hydrolysis of PMMA, a series of P(MMA-MAA) copolymers have been prepared, the MAA content of which depends on the temperature and time of hydrolyzation. In case the MAA content in P(MMA-MAA) is beyond 0.4 mole fraction, the hydrogen bonding between P(MMA-MAA) and PEO is strong enough to form intermolecular complex. The supermolecular structure of the complex is quite different from that of its constituent, which was observed by an X-ray diffraction and transmission electron microscope. The crystallization of PEO is confined owing to complexation. The complex exhibits quite a lot of good properties in thermal stability, gas permeability as well as mechanical strength, and could be used in many fields.     

ISOLATION AND PROPERTIES OF L-AMINO ACID OXIDASE FROM OPHIOPHAGUS HANNAH VENOM

This paper reports the isolation and some properties of L-amino acid oxidase from Ophi-ophagus hannah venom. The differences between L-amino acid oxidase from Ophiophagusohannah and that from other sources in specific activity, properties and the spectrum of iso-zymes are noticeable. The result of electrophoresis on polyacrylamide gel shows that this purified enzyme ishomogenous. The molecular weight determined by gradient polyacrylamide gel slab (4--30%)is around 15×10~4 dalton. The molecular weight of the subunit determined by SDS gradient gelelectrephoresis (4--30%) is around 7.3×10~4 dalton. Therefore, this enzyme is composed of twosubunits. The absorption spectrum reveals that there are two FADs in each molecule. The optimum pH of enzymic reaction is around 8.7--9.0 when L-leucine is used as substrate.The inhibition of the preducts is noticeable when substrate concentration goes beyond 3mM.This enzyme is heat stable and its activity would not decrease obviously after heating at 55℃for 40 min. A linear relationship between enzyme concentration and reaction rate was noticedwhen enzyme concentration was below 5.7μg/ml.     

Investigation of Hydrolysis in Poly（ethylene terephthalate） by FTIR-ATR

The hydrothermal aging of poly(ethylene terephthalate)(PET) was investigated at 70 95 °C. A new method to investigate the hydrolysis degree of PET by Fourier transform infrared spectroscopy(FTIR) was proposed. The spectra during the hydrothermal aging were measured using attenuated total reflection accessory(ATR). Peak resolving of carbonyl regions was performed, and the ratio of two groups of bands representing carboxylic acids and esters respectively were calculated to show the hydrolysis degree of ester groups in PET. The acid/ester ratio shows exactly the same trend as the average chain scission number per unit mass at various temperatures and thus can be used as a parameter to characterize the hydrolysis and random chain scission of PET. This method related to the hydrolysis mechanism directly, is simple, fast and convenient compared to the traditional methods such as viscometry, end-group titration and size exclusion chromatography(SEC). It may also be useful in hydrolysis characterization of other polyesters.     

The Preparation of Perovskite Nano Powder by Sol-gel from DTPA and the Mechanism of Thermal Decomposition

Dy0.8Sr0.2FeO3 nano powder, a synthetic oxide, is made by sol-gel method from metal nitrate and diethylenetriaminepentaaeetic acid (DTPA), and the processing parameters are optimized.The process of the preparation, thermal decomposition and the property of the powder are studied by TG-DTA, IR, TEM, and XRD. The diameter of the average grain is about 70 nm. This new technique can be used in the preparation and the studying of ha‘no materials in the complex oxide system.     

Optical and mechanical properties of polyurethane/surface-modified nanocrystalline cellulose composites

in order to improve the optical and mechanical performances of waterborne polyurethane （WPU）, nanocrystalline cellulose （NCC）/WPU composites were synthesized in this study. NCC （prepared by acid hydrolysis of cotton fiber） was modified by （3-aminopropyl）triethoxysilane （APTES） to enhance its compatibility with WPU, and the surface-modified NCC was characterized by grafting ratio, crystallinity and contact angle （CA）. NCC/WPU composites were examined by scanning electron microscopy （SEM）, X-ray powder diffraction （XRD） and thermogravimetric analysis （TG）. The anti-yellowing property, specular gloss, pencil hardness, and abrasion resistance of NCC/WPU composites were investigated by the methods of Chinese National Standards GB/T 23999-2009, GB/T 9754-2007, GB/T 6739-2006 and GB/T 1768-2006, respectively. The results showed that the grafting ratio of NCC modified by 6% APTES was 36.01% and the crystallinity of modified NCC was decreased with the enhancement of APTES. CA of the modified NCC was decreased by 28.8% and the nanoparticles were homogeneously dispersed in the WPU matrix. The XRD patterns of the NCC/WPU composites were relatively steady, while the thermal stability of the composites was enhanced by 6.7% with 1.0 wt% modified NCC. Modified NCC affected the specular gloss of NCC/WPU composites more obviously than the anti-yellowing property. The pencil hardness of NCC/WPU composites was increased from 2H to 4H by addition of NCC and the abrasion resistance of the composites was enhanced significantly. In general, NCC/WPU composites showed significant improvements in the optical and mechanical performances.     

Synthesis of vegetable oil based polyol with cottonseed oil and sorbitol derived from natural source

In order to prepare the polyol with all bio-based components as raw materials,cottonseed oil was first epoxidized by peroxyformic acid generated in situ from hydrogen peroxide and formic acid,and the cottonseed oil based polyols with variable hydroxyl value were then prepared by the ring-opening of epoxidized cottonseed oil with sorbitol,which is a multi-functional hydroxyl compound derived from a natural source.The chemical structure of the products was characterized with FTIR analysis, and the residual...     

Adsorptive removal of nitrogen-containing compounds from fuel by metal-organic frameworks

The adsorptive denitrogenation from fuels over three metal-organic frameworks(MIL-96(Al),MIL-53(Al)and MIL-101(Cr))was studied by batch adsorption experiments.Four nitrogen-containing compounds(NCCs)pyridine,pyrrole,quinoline and indole were used as model NCCs in fuels to study the adsorption mechanism.The physicochemical properties of the adsorbents were characterized by XRD,N2physical adsorption,FT-IR spectrum and Hammett indicator method.The metal-organic frameworks(MOFs),especially the MIL-101(Cr)containing Lewis acid sites as well as high specific surface area,can adsorb large quantities of NCCs from fuels.In addition,the adsorptive capacity over MIL-101(Cr)will be different for NCCs with different basicity.The stronger basicity of the NCC is,the more it can be absorbed over MIL-101(Cr).Furthermore,pore size and shape also affect the adsorption capacity for a given adsorbate,which can be proved by the adsorption over MIL-53(Al)and MIL-96(Al).The pseudo-second-order kinetic model and Langmuir equation can be used to describe kinetics and thermodynamics of the adsorption process,respectively.Finally,the regeneration of the used adsorbent has been conducted successfully by just washing it with ethanol.     

THE APPLICATION OF ION EXCHANGERS IN THE PREPARTION OF WHEAT AGGLUTININ

In order to refine the products of wheat germ agglutinin (WGA) , several ion exchangers, such as D261,732, DEAE - cellulose -32 and CM - cellulose - 32, have been used to removed proteins and pigments with different colors, such as brown, red, yellow, green and black, in the extracts of wheat germ. The WGA obtained from this procedure has higher hemagglutination activity than that available from sigma Co. The minimum hemagglutination dose of the purified WGA for an equal volume of a 2% type A red blood cells is 4μg/ml. WGA is a mixture of isolectins with different isoelectric points, 5. 9, 6. 2 and 6. 8. Their molecular weight identified by SDS-polyacrylamide gel electrophoresis are 15 ,000 dalton , 18,000 dalton and 35,000 dalton, respectively.     

Hydrolysis of cellobiose catalyzed by zeolites—the role of acidity and micropore structure

The roles of acidity and micropore structure of zeolite were studied in the hydrolysis of the model oligosaccharide of cellulose–cellobiose. HZSM-5, HY, HMOR and Hβ zeolites were selected as model catalysts for the hydrolysis of cellobiose. The effect of acidity of zeolite, including the strength, type and location, on its catalytic activity was investigated. The strong Br?nsted acid sites located in micropores are the active sites for the hydrolysis of cellobiose to glucose. Meanwhile, the catalytic performance of zeolite is also dependent on the micropore size of zeolite.     

STUDIES ON TUNG OIL COATED REGENERATED CELLULOSE FILMS WITH WATERRESISTANCE

Regenerated cellulose films with water-resistance were obtained by an improved method ofpreparing cellulose cuoxam solution from pulps of agricultural wastes (linters, wheat straw, reedand Bamao). Experimental results showed that the mechanical properties of both the dry. and wetfilms were excellent. Data from IR, SEM and tensile strength measurements implied that thesignificant improvement of water-resistance of the films was due to the cohesion between the thinTung oil covers with hydrophobicity and the regenerated cellulose films. The films werecompletely biodegraded after being buried in soil for 100 days. The transmittance of the filmsderived from linter and reed in visible band range were 80-90%.     

BAND-LIKE TEXTURE OF ETHYLCYANOETHYL CELLULOSE MESOPHASE

In the ethyl-cyanoethylcellulose ((E-CE)C)/dichloroacetic acid (DCA) cholesteric liquid crystalline solution, the hand-like texture is formed when the mesophase aggregates with the disk-like texture grow to big enough and merge with each other with increasing concentration. The band-like texture is composed of parallel equidistant bright and dark alternative strips which are about 0.2-2.0 μm in width. In the band-like texture, the layers of ordered polymer chains are perpendicular to the solution film and the axes of helicoids are parallel to it. The width of the strips is different in different zones. Under the effect of an external magnetic field, the strips in the band-like texture first become wider and then narrower gradually.Moreover, the axes of helicoids in the (E-CE) C/DCA mesomorphic solution change from the direction normal to the magnetic field to the agreement with the magnetic field direction.     

烷烃溶剂热法合成单分散硒化锌准纳米球

Monodispersed ZnSe quasi-nanospheres have been prepared by a hydrocarbon solvothermal route at 180℃ using decahydronaphthalene, zinc stearate and selenium as starting materials. The as-obtained products were characterized by SEM, TEM, XRD, elemental analysis and electron-diffraction techniques. Electron microscopy reveals that ZnSe particles prepared in decahydronaphthalene are monodispersed with an average particle size of 55 nm. The possible formation mechanism was investigated by changing hydrocarbon solvent. The shape and size of ZnSe particles depend on the structure of hydrocarbon solvent.