多核超顺磁性Ni0.5Zn0.5Fe2O4/SiO2催化载体的制备与表征

采用化学共沉淀法与溶胶-凝胶法相结合, 在制备过程中改变磁性纳米粒子和TEOS的引入方式, 成功地制备了多核超顺磁性Ni0.5Zn0.5Fe2O4/SiO2催化剂载体. 采用透射电子显微镜(TEM)、氮气吸附、X射线衍射(XRD)及物理性质综合测试系统(PPMS)对样品进行了表征, 利用永磁铁对载体的分离效果进行了验证. 研究结果表明, 改进制备方法后, 制备的载体比表面积明显增大, 这有利于催化剂在载体上的分散与固载; 样品的饱和磁化强度明显增加, 表明样品具有很好的磁响应能力, 有利于催化剂的分离, 同时, 载体的超顺磁特性也有利于液相催化体系中催化剂的分散.     

核壳结构Ni0.5Zn0.5Fe2O4/PANI复合纳米材料的制备及表征

采用微乳液法制备出Ni0.5Zn0.5 Fe2O4纳米颗粒以及Ni0.5Zn0.5Fe2O4/PANI核壳结构复合纳米材料,借助FT-IR、XRD、SEM、TEM、VSM等分析手段研究了材料的形貌、结构与磁性能.结果表明:得到的Ni0.5Zn0.5Fe2O4纳米颗粒平均粒径为20hm左右,Ni0.5Zn0.5 Fe2O...     

磁载光催化剂TiO2/SiO2/Ni0.5Fe2.5O4的制备及其催化氧化性能

采用固相反应法制备磁载体(SiO₂/Ni_0.5Fe_2.5O₄),溶胶-凝胶法得到易于磁分离回收的磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄。用XRD、SEM、IR和UV-Vis等进行表征。研究了太阳光下催化剂对亚甲基蓝溶液的脱色性能。结果表明,在太阳光下,磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄可使亚甲基蓝溶液迅速脱色；3次循环使用后脱色率仍为95%以上,回收率为98.8%。     

Ni-Fe-Al-O双金属催化剂在生物质基2-羟基四氢吡喃还原胺化合成5-氨基-1-戊醇中的性能研究北大核心CSCD

采用共沉淀法制备了不同Fe/Ni摩尔比(0、0.125、0.25、0.5和0.75)的Al_(2)O_(3)负载型NiFe单、双金属催化剂,并考察了它们在生物糠醛衍生2-羟基四氢吡喃(2-HTHP)还原胺化合成高附加值5-氨基戊醇反应中的催化性能.研究发现当Fe/Ni摩尔比为0.25时表现出最高的5-氨基戊醇收率(在80℃和2 MPa优化条件下达90%).利用N_(2)吸脱附、X射线衍射(XRD)、氢气程序升温还原(H_(2)-TPR)、透射电镜(TEM)等技术对催化剂进行了表征,结果表明适量Fe的掺入可以提高催化剂的分散性和还原性,同时在还原活化催化剂中形成Ni-Fe合金相,继而使相应催化剂表现出更优异的催化活性.通过固定床对比考察了催化剂的稳定性,NiFe(0.25)-Al-O双金属催化剂表现出明显优于NiFe(0)-Al-O单金属催化剂的稳定性,运行120 h前者只有微弱失活而后者显著失活.对比反应后催化剂表征发现,金属Fe的修饰可以有效抑制金属活性颗粒的烧结和流失,从而显著提高其反应稳定性.     

Ni2+在γ-Al2O3上的分散状态及负载型Ni/γ-Al2O3催化剂的α-蒎烯加氢活性

用X-射线衍射(XRD)、紫外-可见漫散射光谱(UV-Vis DRS)、程序升温还原(TPR)、CO化学吸附和微反测试等方法研究了Ni²⁺在γ-Al₂O₃上的分散状态和负载型Ni/γ-Al₂O₃催化剂的α-蒎烯加氢催化活性。结果表明，当Ni²⁺负载量远低于其在γ-Al₂O₃载体表面分散容量时，Ni²⁺优先嵌入载体表面四面体空位，随着Ni²⁺负载量的增加，嵌入载体表面八面体空位Ni²⁺的比例增大。由于八面体Ni²⁺易被还原为金属态Ni⁰，NiO/γ-Al₂O₃样品的还原度随Ni²⁺负载量的增加而大幅度地增加，经氢还原所得Ni/γ-Al₂O₃催化剂的CO吸附量和α-蒎烯加氢催化活性大幅度增加。对La₂O₃助剂的作用进行了研究，结果表明分散在γ-Al₂O₃上的La³⁺物种可阻止Ni²⁺嵌入γ-Al₂O₃表面四面体空位，增大了八面体Ni²⁺物种所占比例，提高了催化剂的还原度，故Ni-La₂O₃/γ-Al₂O₃催化剂催化活性高于Ni/γ-Al₂O₃催化剂。     

纳米结晶体Ni0.5Zn0.5Fe2O4对高氯酸铵热行为及分解反应动力学的影响

采用差示扫描量热法(DSC)、热重和微分热重(TG-DTG)及固相原位反应池/快速扫描傅立叶变换红外联用技术(hyphenated in situ thermolysis/RSFTIR)研究了纳米结晶体Ni_0.5Zn_0.5Fe₂O₄与高氯酸铵(AP)组成的混合物的热行为和分解反应动力学。结果表明：Ni_0.5Zn_0.5Fe₂O₄使得AP的低、高温分解放热峰温分别提前17.44 K和27.74 K,并使得对应的分解热分别增加3.7 J·g^-1和193.7 J·g^-1。Ni_0.5Zn_0.5Fe₂O₄并不影响AP的晶转温度和晶转热。Ni_0.5Zn_0.5Fe₂O₄使得AP的TG曲线出现3个阶段,并使得后2个失重阶段的初始和终止温度都有所提前。凝聚相分解产物分析表明Ni_0.5Zn_0.5Fe₂O₄加速了凝聚相AP的分解及氨气的释放。含Ni_0.5Zn_0.5Fe₂O₄的AP的高温分解反应的动力学参数E_a=238.88 kJ·mol^-1,A=1018.59 s^-1,动力学方程可表示为dα/dt=10^18.99(1-α)[-ln(1-α)]^3/5e^-2.87×104T。始点温度(T_e)和峰顶温度(T_p)计算得出AP的热爆炸临界温度值分别为:574.83 K和595.41 K。分解反应的活化熵(ΔS^≠)、活化焓(ΔH^≠)和活化能(ΔG^≠)分别为:109.61 J·mol^-1·K^-1、236.49 kJ·mol^-1及172.58 kJ·mol^-1。     

磁性纳米固体超强酸的合成、表征及性能

首次制备了SO₄^2-/Co_0.5Fe_2.5O₄-ZrO₂磁性固体超强酸,利用TEM,DTA,XRD和FTIR等手段研究了Co_0.5Fe_2.5O₄磁性基质对ZrO₂的粒子大小、晶化温度与结构的影响.考察了磁性固体超强酸的催化性能及催化剂的寿命、回收率和磁性.结果表明,引入Co_0.5Fe_2.5O₄磁性基质不但赋予催化剂以磁性,而且在固体超强酸形成过程中延迟了ZrO₂由四方晶相向单斜晶相的转变,有助于稳定样品表面的含硫物种,磁性固体超强酸对酯化反应具有较高的催化活性,可活化再生,并保持磁性.     

Pd catalysts supported on modified Zr0.5Al0.5O1.75 used for lean-burn natural gas vehicles exhaust purification

Composite supports Zr0.5Al0.5O1.75 modified by metal oxides,such as La2O3,ZnO,Y2O3 or BaO,were prepared by co-precipitation method,and palladium catalysts supported on the modified composite supports were prepared by impregnation method.Their properties were characterized by X-ray diffraction(XRD),NH3 temperature-programmed desorption(NH3-TPD),H2 temperature-programmed reduction(H2-TPR),N2 adsorption/desorption,and CO-chemisorption.The catalytic activity and the resistance to water poisoning of the prepared Pd catalysts were tested in a simulated exhaust gas from lean-burn natural gas vehicles with and without water vapor.The results demonstrated that the modified supports had an apparent effect on the performance of Pd catalysts,compared with the Pd catalyst supported on the unmodified ZrAl.The addition of ZnO or Y2O3 promoted the conversion of CH4.In the absence of water vapor,Pd/ZnZrAl exhibited the best activity for CH4 conversion with the light-off temperature(T50) of 275℃ and the complete conversion temperature(T90) of 314℃,respectively.However,in the presence of water vapor,Pd/YZrAl was the best one over which the light-off temperature(T50) of methane was 339℃ and the complete conversion temperature(T90) was 371℃.These results indicated that Pd catalyst supported on the modified composite ZrAl support showed excellent catalytic activity at low temperature and high resistance to H2O poisoning for the exhaust purification of lean-burn natural gas vehicles.     

Autothermal reforming of methane over Ni catalysts supported over ZrO2-CeO2-Al2O3

Ni catalysts supported on Al2O3, ZrO2-Al2O3, CeO2-Al2O3 and ZrO2-CeO2-Al2O3 were prepared by coprecipitation method, and their catalytic performances for autothermal reforming of methane to hydrogen were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS. The relationship between the structures and catalytic activities of the catalysts was discussed. The results showed that the catalytic activity and stability of the Ni/ZrO2-CeO2-Al2O3 catalyst was better than those of other catalysts with the highest CH4 conversion, H2/CO and H2/COx ratio at 750 ℃. The catalyst showed a little deactivation along the reaction time during its 72 h on stream with the mean deactivation rate of 0.08%/h. The catalytic performance of the Ni/ZrO2-CeO2-Al2O3 catalyst was also affected by reaction temperature, no2 ： nCH4 molar ratio and nH2O ： nCH4 molar ratio. TPR, XRD and XPS measurements indicated that the formation of ZrO2-CeO2 solid solution could improve the dispersion of NiO, and inhibit the formation of NiAl2O3, and thus significantly promoted the catalytic activity of the Ni/ZrO2-CeO2-Al2O3 catalyst.     

Ce0.5Zr0.5O2修饰的Ni/SiC、Fe/SiC和Co/SiC催化燃烧甲烷性能

以铈锆固溶体(Ce0.5Zr0.5O2)修饰的高比表面积SiC为载体,采用两步浸渍法制备了Ni、Fe和Co基催化剂,研究了其在煤层气催化燃烧脱氧中的催化活性和稳定性.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、电感耦合等离子体质谱(ICP-MS)、高分辨透射电子显微镜(HRTEM)、比表面积(BET)、热重分析(TGA)和H2程序升温还原(H2-TPR)对催化剂进行了表征.分析结果表明,Ni、Fe和Co部分进入Ce0.5Zr0.5O2固溶体晶格内部,导致催化剂体相形成更多的缺陷;同时Ce0.5Zr0.5O2固溶体有助于加速金属氧化物和金属之间氧化还原过程的进行,促进了氧吸附、传输和对甲烷的活化.另外,SiC和Ce0.5Zr0.5O2固熔体良好的抗积碳性能,有效避免了催化剂在富甲烷反应气氛中因积碳而失活,从而使三种催化剂均具有优良的催化燃烧脱氧活性和稳定性.其中,Co/Ce0.5Zr0.5O2/SiC活性最高,可在320℃活化催化甲烷,并在410℃实现完全脱氧.     

镍钴锌纳米铁氧体的制备及磁热性能

以乙酰丙酮盐为前驱体,三乙二醇为溶剂,采用多元醇法制备了纳米Ni0.5-xCoxZn0.5Fe2O4(x=0,0.1,0.2,0.3和0.4)铁氧体.通过X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)和振动样品磁强计(VSM)等对样品的结构、形貌和磁性能进行了表征.结果表明,所得纳米Ni0.5-xCoxZn0.5Fe2O4铁氧体的分散性较好,尺寸均一.在室温下产物的剩磁和矫顽力均较小,表现出亚铁磁性.纳米Ni0.3Co0.2Zn0.5Fe2O4铁氧体的饱和磁化强度达到41.34 A·m2·kg-1,其在交变磁场中升温可达到55℃,表现出较好的磁热性能.     

Methane oxidation at redox stable fuel cell electrode La0.75Sr0.25Cr0.5Mn0.5O(3-delta)

Because of its widespread availability, natural gas is the most important fuel for early application of stationary fuel cells, and furthermore, methane containing biogases are one of the most promising renewable energy alternatives; thus, it is very important to be able to efficiently utilize methane in fuel cells. Typically, external steam reforming is applied to allow methane utilization in high temperature fuel cells; however, direct oxidation will provide a much better solution. Recently, we reported good electrochemical performance for an oxide anode La0.75Sr0.25Cr0.5Mn0.5O3 (LSCM) in low moisture (3% H2O) H2 and CH4 fuels without significant coking in CH4. Here, we investigate the catalytic activity of this oxide with respect to its ability to utilize methane. This oxide is found to exhibit fairly low reforming activity for both H2O and CO2 reforming but is active for methane oxidation. LSCM is found to be a full oxidation catalyst rather than a partial oxidation catalyst as CO2 production dominates CO production even in CH4-rich CH4/O2 mixtures. X-ray adsorption spectroscopy was utilized to confirm that Mn was the redox active species, clearly demonstrating that this material has the oxidation catalytic behavior that might be expected from a Mn perovskite and that the Cr ion is only present to ensure stability under fuel atmospheres.     

CO氧化反应中H2O对MOx和Au/MOx催化性能的影响

过渡金属氧化物［1,2］及负载型贵金属催化剂［3～13］是催化氧化消除CO的有效催化剂,一直是研究的热点. 虽然对MOx和Au/MOx上CO的氧化性能研究得较多,但大多是在无水条件下进行的;涉及催化剂抗水性能的报道较少［3,9,10］,且仅限于对催化剂活性的研究. Haruta等［3］对Au/Fe2O3,Au/Co3O4和Au/TiO 2等体系开展了一些工作, 认为水对CO氧化活性有促进作用. 本文重点考察了水对MOx(M=Al,Ca,Co,Cr,Cu,Fe,La,Mn,Ni和Zn)催化剂上CO氧化活性的影响,以及水对Au/MOx 催化剂活性及稳定性的影响.     

Synthesis of polycarbonate diol catalyzed by metal-organic framework Zn_4O[CO_2-C_6H_4-CO_2]_3

The metal-organic framework Zn4O[1,4-benzenedicarboxylate]3(Zn4O[CO2-C6H4-CO2]3,commonly known as MOF-5,was prepared by the ultrasonic irradiation method.The catalyst was characterized by X-ray diffraction(XRD) and Fourier transform infrared(FTIR) spectroscopy.It was then used as the catalyst for the preparation of polycarbonate diol(PCDL) via the transesterification between diphenyl carbonate(DPC) and 1,6-hexandiol(1,6-HD).Its catalytic activity in the transesterification process is evaluated by the yield ...     

BaTiO3-BaAl2O4-Al2O3复合载体的制备、表征及其Ni基催化剂催化CH4/CO2重整反应性能

以十六烷基三甲基溴化胺为结构导向剂,采用溶胶-凝胶法制备了BaTiO3-BaAl2O4-Al2O3复合载体,采用X射线衍射、红外光谱、N2吸附-脱附、透射电子显微镜和H2程序升温还原等技术对复合载体进行了表征,并以CH4/CO2重整制合成气为探针反应,考察了不同Ni/BaTiO3-BaAl2O4-Al2O3催化剂的性能.结果表明,BaTiO3-BaAl2O4-Al2O3复合载体具有多孔织构特性和较高的比表面积,BaTiO3和BaAl2O4以晶粒状态分布在复合载体的内外表面,晶粒尺寸在20～50nm的范围,复合载体孔径为10～20nm.复合载体上BaTiO3和BaAl2O4的引入,适度削弱了Ni/BaTiO3-BaAl2O4-Al2O3催化剂中Ni物种与γ-Al2O3间的强相互作用,抑止了NiAl2O4尖晶石的生成;当载体中Ba(Ti)含量为17.33%时,其负载的Ni催化剂上CH4/CO2重整制合成气反应的活性和稳定性最高.     

Caesium carbonate supported on hydroxyapatite‐encapsulated Ni0.5Zn0.5Fe2O4 nanocrystallites as a novel magnetically basic catalyst for the one‐pot synthesis of pyrazolo[1,2‐b]phthalazine‐5,10‐diones

A novel nanomagnetic basic catalyst of caesium carbonate supported on hydroxyapatite‐coated Ni_0.5Zn_0.5Fe₂O₄ magnetic nanoparticles (Ni_0.5Zn_0.5Fe₂O₄@HAP‐Cs₂CO₃) was prepared. This new catalyst was fully characterized using Fourier transform infrared spectroscopy, transmission and scanning electron microscopy, X‐ray diffraction and vibrating sample magnetometry techniques, and then the catalytic activity of this catalyst was investigated in the synthesis of 1H‐pyrazolo[1,2‐b]phthalazine‐5,10‐dione derivatives. Also, Ni_0.5Zn_0.5Fe₂O₄@HAP‐Cs₂CO₃ could be reused at least five times without significant loss of activity and could be recovered easily by applying an external magnet. Thus, the developed nanomagnetic catalyst is potentially useful for the green and economic production of organic compounds. Copyright © 2015 John Wiley & Sons, Ltd.     

聚苯胺/Co_(0.5)Zn_(0.5)Fe_2O_4纳米复合材料的制备及电磁性能

采用高分子凝胶法制备尖晶石型Co0.5Zn0.5Fe2O4,原位聚合法制备纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4纳米复合材料.使用傅立叶红外光谱(FTIR)、紫外可见吸收光谱(UV-Vis)、X射线衍射仪(XRD)和透射电子显微镜(TEM)对复合材料进行了表征.FTIR和XRD的结果表明样品为纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4.UV-Vis光谱表明聚苯胺/Co0.5Zn0.5Fe2O4苯环上的π-π*和n-π*分别红移了23nm和5nm.TEM照片可知,聚苯胺和聚苯胺/Co0.5Zn0.5Fe2O4粒子的平均粒径分别约为50nm和70nm.在8.2～12.4GHz测试频率范围内,聚苯胺/Co0.5Zn0.5Fe2O4的ε″数值在9.2～12.3之间,u″数值在0.15～0.16之间;聚苯胺/Co0.5-Zn0.5Fe2O4介电损耗低于纯聚苯胺,而磁损耗高于纯聚苯胺.     

磁性纳米粒子负载钯催化有机合成反应研究进展

磁性纳米粒子负载钯催化的有机合成反应,由于具有催化活性高,催化剂在外加磁场作用下即可快速分离和重复使用等特点,已引起了人们的广泛关注.综述了近年来磁性纳米粒子负载钯催化有机合成反应的研究进展,载体包括Fe3O4纳米粒子、有机小分子修饰的磁性纳米粒子、SiO2包覆的磁性纳米粒子、碳修饰磁性纳米粒子、羟基磷灰石包覆的磁性纳米粒子和有机高分子修饰的磁性纳米粒子等.     

Influence of support on resistance to carbon-deposition of catalyst for CH4, CO2 with O2 to synthesis gas

In the reaction of catalytic oxidation of CH4,CO2 with O2 to synthesis gas, carbon-deposition is an important factor for deactivation. By adding different oxides to Ni/AI2O3 catalyst, its resistance to carbon-deposition was improved. The experimental results indicate that the order of resistance to carbon-deposition is as follows: Ni/CaO-AI2O3>Ni/MgO-AI2O3>Ni/ TiO2-AI2O3>Ni/CeO2-AI2O3>Ni/La2O3-AI2O3>Ni/Y2O3-AI2O3>Ni/Fe2O3-AI2O3>Ni/AI2O3. The catalysts were characterized by CO2-TPD, O2-TPD and XPS methods. Here the relation between the order of resistance to carbon-deposition and performance of catalyst is discussed.     

Ni-Fe催化剂乙醇部分氧化制氢的研究

研究了Ni Fe催化剂对乙醇部分氧化制氢反应,系统地考察了不同O2/C2H5OH摩尔比及反应温度下催化剂的性能.发现Ni Fe催化剂对乙醇部分氧化制氢具有较好的催化活性,其中组成为Ni50Fe50催化剂最好,最佳的反应条件是O2/C2H5OH=1.0,T=573 K.XRD谱图表明催化剂主要由尖晶石结构的铁酸盐和FeNi3合金相组成. XPS结果说明,催化剂体相以还原态FeNi3合金相为主,表面以氧化态的铁酸盐为主.稳定性考察的结果表明,催化剂经40 h反应后,对氢的选择性明显下降,此时对应的FeNi3物相衍射峰强度也明显降低,表明催化剂对H2选择性的下降与FeNi3物相的转变有关.