铈掺杂纳米ZnO结构与室温脱硫性能的相关性研究

Nano-ZnO desulfurizer doped with cerium was prepared by homogeneous precipitation. The bulk and surface structures were characterized by TG-DTA, XRD, XPS and TEM. The desulfurizing performance at ambient temperature was studied. The results show that at ambient temperature the desulfurizing activities of nano-Ce-ZnO desulfurizer are closely related to the particle size, the electron density on desulfurizer surface and the quantity of active sites. Compared with nano-ZnO, nano-Ce-ZnO desulfurizer calcined at 270 ℃ showed smaller particle size and higher surface electron density, which favored the adsorption and reaction of H₂S, resulting in improved desulfurizing activity at ambient temperature since the quantity of Zn^(2-δ)+ became greater by electron gain of zinc ion from cerium ion. The tendency for zinc and cerium to be separated out as individual oxide from Ce-ZnO desulfurizer would increase as the calcination temperature was raised. The enrichment of cerium on the surface of ZnO made decrease the active sites for H₂S adsorption, which led to the decrease in desulfurization activity at ambient temperature.     

锐钛矿型TiO2水溶胶的低温制备及其表征

Anatase titanium dioxide hydrosol was prepared at low temperature by a simple method. The title material was characterized by TEM, XRD, FTIR and BET, respectively. The photocatalytic activity of the as-prepared TiO₂ was evaluated by the degradation of methyl orange solution under sunlight and the photocatalytic oxidation of acetone in air. The results showed that the titanium dioxide hydrosol was composed of anatase phase with average grain size of about 7 nm, and the crystallinity became more perfect with the increase of temperature. The BET surface areas were more than 220 m²·g^-1 for these samples. It is found that the photocatalytic activity was much better for the higher heat processing temperature. Especially, the photocatalytic activity of the sample with a heat treatment of 110 ℃ was better than that of P25. In addition, TiO₂ hydrosol also possessed good photocatalytic activity under the sunlight illumination.     

水热处理氢氧化镁微晶性质研究

Shape apprearance and crystallite characterization of magnesium hydroxide at different hydrothermal tempera-tures have been investigated by SEM， XRD and DSC methods. The grain size， cell parameter and lattice distortion rate of powders under each condition were obtained. The results show that the grains had grown up， especially along the (001) surface as the hydrothermal temperature was raised， accompanying the shrinkage of lattice and the de-scending of distortion rate. These could be relate to the re-crystallization of Mg(OH)₂， as well as the thermal dif-fusion of OH^- with lower charges， resulting in good dispersion， high thermal decomposition temperature and en-thalpy of Mg(OH)₂. Moreover， it is helpful for the increase of the retardant behavior of Mg(OH)₂.     

石墨负载Pt催化剂的制备、表征及活性研究

Pt/graphite catalyst was prepared by incipient wetness impregnation using H₂PtCl₆·6H₂O as precursor. The catalyst was characterized by SEM, XRD, XPS and its degradation ability for oxalic acid was evaluated. The preparation parameters, including the reduction temperature, Pt loading and pyrolysis were studied. The optimal preparation conditions were 350 ℃ with Pt loading of 1.0%. Results show that the loading of Pt can significantly enhance catalytic activity of graphite and that Pt/graphite catalytic ozonation can effectively remove oxalic acid in aqueous solution. The BET surface area of graphite is much smaller than that of activated carbon, however, the catalytic activity of Pt/graphite towards oxalic acid degradation is higher than that of Pt/AC. The XPS results indicate that the active phase at catalyst surface is in the form of Pt⁰. Compared with that of reduction process in hydrogen, the activity of Pt/graphite catalyst decreases when it is prepared by pyrolysis in air due to the lower Pt dispersion on graphite surface.     

氢气泡模板电沉积多孔金属镍薄膜

Porous nickel films have been successfully electrodeposited using cathodic hydrogen bubbles as a template. The influence of deposition parameters including concentration, temperature and current density on the films morphologies has been systematically studied. SEM results showed that increase in current density resulted in the deposits with higher pore density and smaller pore size. Both the pore size and thickness of the pore walls increased with the electrolyte temperature range from 20 to 60 ℃ when the other deposition parameters were fixed. Increasing the concentration of NiCl₂ or NH₄Cl in the electrolyte led to the thicker of the pore walls and declined pore size and density. The deposits displayed a dendritic morphology in cross-sectional SEM image. Electrochemical characterization of the porous nickel films after surface oxidation in 1.0 mol·L^-1 NaOH solution showed that specific capacitance as high as 7.2 F·g^-1 could be reached.     

预氧化对石油焦物理活化的作用

Activated carbon was prepared from pretreated petroleum coke by the vapor activation. The effect of pretreatment process on activation performance of coke was studied by low temperature N₂ adsorbtion-desorption and XRD. The results show that when the temperature is increased, coke loses volatiles with obvious volume contraction, resulting in decline in coke activation performance, the activated carbon obtained from carbonization coke after treatment at 650 ℃ is with a higher degree of graphitization, while pores below 1.5nm are disappeared. The oxidation pretreatment would modify the micro-structure of the coke and make the graphitization degree of coke decline. The activation performance of coke is improved greatly by air-oxidation pretreatment due to the formation of a mass of pore in coke with specific surface area about 146 m²·g^-1, and the surface area of activated carbon is considerably increased. The specific surface area of the activated carbon from air-oxidated coke reached 499m²·g^-1. Nitric acid pretreatment also had effect on improving activating performance of the petroleum coke.     

水热法制备高纯超细CeO2-ZrO2复合氧化物

Superfine composite powders of CeO₂-ZrO₂ (CZ) and CeO₂-ZrO₂-La₂O₃ (CZL) were prepared by hydrothermal method. The effects of pH、temperature and time for hydrothermal process on the performance of the resulting powders were studied. The optimized reaction parameters were on follows: the precursor′s pH≈9.0, hydrothermal temperature of 200 ℃ holding for 2 h. Thermal stable powders with average particle size smaller than 10 nm and specific surface area of 171 m²·g^-1 were obtained. A BET specific surface area was still at 44 m²·g^-1 after calcination at 1 000 ℃ for 6 hours.     

纳米固体超酸SO42-/TiO2的研究

The new nanosolid superacid catalyst SO₄^2-/TiO₂ is compounded with nanometer chemical technology. This catalyst SO₄^2-/TiO₂ has good catalytic effects on esterificational reactions of ethylic acid and ethyl alcohol. It has many other advantages such as strong water-proof quality, being able to be used repeatedly, being easy to be re-claimed, non-corroding, non-polluting. So it is a green industrial catalyst which is helpful to the environment and possesses wide prospect of applications. The crystallo-process, specific surface area and sulphur content of the SO₄^2-/TiO₂ system have been studied with the method of XRD, XPS and the chemical analysis, the result of which indicates that catalytic activity and acid strength of SO₄^2-/TiO₂ is affected by the H₂SO₄ saturant concentration, baking temperature, precipitating condition, specific surface area and sulphur content. The best preparation conditions of SO₄^2-/TiO₂ are: ageing temperature at 0℃, 0.5mol·L^-1 of H₂SO₄ concentration, baking temperature at 500℃and 3 hours of baking time.     

无氨湿法制备纳米晶In2O3及表征

Preparation of In₂O₃nano-scale powders by ultrasonic and homogeneous precipitation, using metal In and urea as raw materials, was reported for the first time, while the effects of reaction temperature, the ratio of the materials and the pH etc. on the preparation was dicussed. This method can be operated and industrialized easily with very low cost． The structural properties of precursor and In₂O₃were characterized by TG-DTA, XRD, ESCA and TEM. The results show that In₂O₃produced are very pure, monophase and spherical nano-scale powders with average size of 25 nm.     

纳米三氧化二钴低温热容和热力学性质的研究

The isobaric molar heat capacities of nano Co₂O₃ were determined by an adiabatic calorimeter in the temper-ature range from 78 to 350K. No phase transition takes place in this temperature range. The relationship of C_p，m with respect to thermodynamic temperature T was established as C_p，m=-11.998X³-9.6431X²+63.478X+81.291(J·K^-1·mol^-1) ， where X=(T-201.903)/121.535， the correlation coefficient R₂=0.9996. Ac-cording to this relationship and the relationships between thermodynamic functions， the thermodynamic functions of nano Co₂O₃ relative to the standard temperature of 298.15K were derived based on the measured heat capacity data. The average grain size of the studied nano Co₂O₃ sample was determined to be 12nm by TEM.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

Preparation and structure of NaSr0.5Al2B2O7 and NaCa0.5Al2B2O7

Two compounds NaSr_0.5Al₂B₂O₇ and NaCa_0.5Al₂B₂O₇, have been found to crystallize into a new structure type by Rietveld refinement from X-ray powder diffraction data. Their structure belongs to hexagonal space group P6₃/m, with lattice parameters of , for NaSr_0.5Al₂B₂O₇ and , for NaCa_0.5Al₂B₂O₇, respectively. The structure is built up by [Al₂B₂O₇]²⁻ double layer and Na⁺/Ca²⁺ or Na⁺/Sr²⁺ ions alternatively stacking along the c-axis. The sites in the inter-double layer are fully occupied jointly by Na and Ca or Sr, but the intra-double layer sites are only half occupied solely by Na. A mechanism of the transition of the structure from CaAl₂B₂O₇ to present structure type by replacing only 1% Ca by Na (2%) as observed by Chang and Keszler (Mater. Res. Bull. 33 (1998) 299) is also proposed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…