超分子结构水杨酸根插层水滑石的组装及结构与性能研究

以锌铝水滑石ZnAl-CO3 LDHs为前体（主体），以乙二醇为分散介质，用离子 交换法组装了水杨酸根（客体）插层水滑石ZnAl-[o-HO(C6H4)COO]LDHs，并用XRD ，FT-IR，TG-DTA等手段对样品进行了表征。结果表明，能过控制离子交换条件， 水杨酸根阴离子可取代锌铝水滑石前体层间的CO3^2-离子，组装得到晶体结构良好 的水杨酸根插层水滑石。通过研究发现，主体水滑石层板与客体以静电力和氢键相 互作用，得到的超分子结构材料紫外阻隔作用增强并具有较好的稳定性，从而成为 一种集屏蔽和吸收双重功能的新型无机-有机得合紫外阻隔材料。     

镁铝水滑石层板与层间阴离子相互作用的理论研究

本文采用以ASED-MO(含原子对排斥的EHMO法)为基础的结构自动优化的EHTOPT程序,对镁铝水滑石(LDHs)层板与层间阴离子相互作用进行了理论研究.以Mg6Al2(OH)16X@H2O为分子结构单元,计算并分析了与不同层间阴离子形成稳定结构的能量变化、成键状况及电荷转移情况,揭示了层间作用力的本质.结果表明,LDHs层板与层间阴离子间存在静电吸引、氢键等非共价键弱相互作用,且氢键作用为主,其强弱与阴离子电荷分布、空间排布方式密切相关;层间阴离子电荷分布同时还影响着层板酸碱性的变化.     

用焙烧复原法插层组装有机层柱双氢氧化物

有机酸根插层双氢氧化物(简记为:LDHs OA)是制备具有特殊性质和功能的层柱材料的一类重要前驱体[1 3]。本文以Mg6Al2(OH)16CO2-3·6H2O(简记为MgAl CO2-3)和Zn6Al2(OH)16CO2-3·4H2O(简记为ZnAl CO2-3)为前体,用焙烧复原法将十四酸根(简记为14A)和十八酸根(简记为18A)分别插层组装到了MgAl LDHs和ZnAl LDHs层板间而制得了具有大的层间距、良好的结晶度和规整的层状结构的14A(18A)插层LDHs层柱材料(分别简记为MgAl 14A,mgAl 18A,ZnAl 14A,ZnAl 18A),用XRD谱、IR谱表征了插层交换产物的结构。1　实验部分1.1　仪…     

金属氢氧化物直接制备对苯二甲酸插层水滑石及其应用

以新制备的Mg(OH)_2和Al(OH)_3滤饼与对苯二甲酸通过水热反应制备了对苯二甲酸插层水滑石(TALDHs).使用X射线衍射(XRD)、热重-差热分析、扫描电镜(SEM)等技术对TA-LDHs与碳酸根型水滑石(CO3-LDHs)进行对比研究,结果显示,对苯二甲酸离子成功插入到LDHs层间,产物结构完整、晶相单一,所制得的TA-LDHs为片状.CO3-LDHs和TA-LDHs分别作为纳米填料,以两种不同的添加方式制备聚对苯二甲酸乙二醇酯(PET)/LDHs纳米复合材料.对复合材料进行XRD和SEM研究,结果表明在酯交换反应前添加2%TA-LDHs所制备的PET/LDHs纳米复合材料的层板被部分剥离,分散性最好.     

新原料路线共沉淀法组装超分子结构柠檬酸根插层水滑石

以Mg(OH)₂和NaAlO₂为原料，采用新原料路线共沉淀法实现了柠檬酸根插层结构LDHs的超分子组装。用XRD、FT-IR、TG-DTA和元素分析等手段对样品进行分析表征。结果表明，新原料路线共沉淀法较常用的共沉淀法得到的柠檬酸根插层LDHs结晶度高、晶相单一，客体柠檬酸根在LDHs层间的排列高度有序。     

超分子结构甲基橙插层水滑石的组装及其光热稳定性研究

甲基橙是一种酸性染料,但因为它的光和热稳定性较差,使其应用范围和使用效果受到了一定限制.以Mg_0.67Al_0.33(OH)₂(CO₃)_0.165·0.58H₂OLDHs为前体,采用离子交换法,将甲基橙插入到LDHs层间,借助XRD,FTIR,UV-Vis和TG-DTA等手段对样品进行表征.结果表明,甲基橙阴离子可以完全取代前体层间的CO₃^2-离子,组装得到晶体结构良好的甲基橙插层LDHs.对其结构进行研究发现,LDHs主体层板与客体甲基橙阴离子之间存在静电吸引、氢键和其它弱化学键相互作用,具有超分子结构特征.该超分子结构材料不仅保持了甲基橙本身的颜色,而且与甲基橙相比,其耐光性和耐热性均有大幅度的提高.     

镁锡水滑石中的超分子作用

通过构建镁锡水滑石(Mg3Sn-LDHs-yH2O)周期性计算模型,基于密度泛函理论,用CASTEP程序模块,进行模型的几何全优化.对各体系的结构参数、Mulliken电荷布居、态密度(DOS)、逐级水合能等进行分析,探究客体CO320-和H2O的分布形态及其与主体层板的超分子作用.结果表明,[Mg6Sn2(OH)16]4+层间插入客体阴离子CO320-和水分子后,主客体间存在着较强的超分子作用力,主要包括静电和氢键作用,且氢键作用在水合过程中起主导作用,总体上层板-水(L-W)型/层板-阴离子(L-A)型氢键强度要强于阴离子-水(A-W)型/水-水(W-W)型氢键.随着层间水分子的增多,层间距先增大后又稍降低.当y=0、1时,客体所在的平面与主体层板平行,且与两层板的距离基本相等;当y=2、3时,客体以偏向某一层板的形式存在.与层间H2O相比,层间阴离子CO230-对体系态密度的影响更显著,层板与CO320-的总体作用力大于与H2O的总体作用力.随着水分子数的增加,Mg3Sn-LDHs-yH2O体系的逐级水合能绝对值逐渐降低,说明Mg3Sn-LDHs的水合程度不会无限增加,而是具有饱和量.     

二元类水滑石层板组成、结构与性能的理论研究

采用晶体学理论建立二元类水滑石(LDHs)微观结构模型与静电势能模型，将层板金属离子间距、层板电荷密度、层间阴离子间距等微观结构参数定量化，并将层间阴离子的静电势能表示成层板金属离子半径和物质的量之比、插层阴离子尺寸和电荷的函数。研究结果表明：LDHs层板金属离子间距应用离子紧密堆积来估算和孔径按阴离子平面六方点阵分布来计算是可行的；调变层板金属离子种类与物质的量之比影响层间阴离子的稳定性，势能计算值与文献报道的LDHs热稳定性次序一致。所以该模型可用于预测LDHs的微观结构参数以及热稳定性，为新型层状双羟基材料的定向合成提供思路。     

LDHs主体层板与卤素阴离子超分子作用的理论研究

构建了LDHs主客体作用模型, 采用混合密度泛函B3LYP方法, 在6-31G(d)水平上进行结构优化和频率分析, 然后分别用6-31G(d)和6-311++G(d, p)基组计算主客体相互作用能, 从几何参数、电荷布居、前线轨道、能量以及热力学参数等角度探讨LDHs主体层板与卤素阴离子(F?, Cl?)间的超分子作用. 计算结果表明, LDHs主体层板复合卤素阴离子是一个自发过程. LDHs主客体间存在着较强的超分子作用, 主要包括静电和氢键作用, 相互作用能分别为?592.45和?444.01 kJ·mol?1. LDHs主体层板与卤素阴离子的前线轨道发生作用, 电子容易从卤素阴离子的HOMO向层板的LUMO转移, 形成的组装产物Mg6Al(OH)14+?F?比Mg6Al(OH)14+?Cl?稳定.     

表面预处理对镁铝水滑石结构性质和缓释性能影响

以Mg-Al-NO3水滑石(LDHs)为载体,将5-氟尿嘧啶(5-FU)通过离子交换法插入其层间,得5-FU/LDHs缓释材料。并对水滑石表面进行弱酸预处理改性,利用XRD、FTIR、TG-DSC、SEM和零电荷点(pHPZC)等表征手段,考察酸预处理对水滑石表面化学性质及微观结构的影响。结果表明,5-FU/LDHs的层间距从0.858 nm扩大到1.064 nm,层间5-FU2阴离子与主体层板通过氢键与静电作用,以呈一定角度单层交替排列于层间。酸预处理的水滑石粒径变小,层板正电荷密度增大。5-FU的释放机理是物理扩散、离子交换和药物溶解等协同作用,酸预处理可提高水滑石的缓释性能和稳定性。     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

两种甲醇水蒸气重整制氢催化剂的研究

对采用共沉淀法制备的CuZnAlO类铜系催化剂和采用水滑石类层柱材料（LDHs）前驱体制备的催化剂在甲醇水蒸气重整制氢反应中的性能进行了研究。对共沉淀法制备的CuZnAlO类铜系催化剂考察了ZrO2助剂的加入对催化剂反应性能的影响，发现Zr的质量分数为10％的催化剂显著提高CuZnAlO催化剂的反应性能。该催化剂的最佳反应条件：0.1 MPa、250 ℃、H2O/MeOH摩尔比1.0～1.3、3.56 h－1。在此反应条件下进行了COPZr2催化剂150 h稳定性实验。结果表明，该催化剂具有很好的反应稳定性。甲醇转化率和氢产率分别约为88％和83％，产物湿基组成中H2和CO的质量分数分别为>63％和0.20％～0.31％。对LDHs前驱体制备的催化剂，进行了70 h反应稳定性实验，结果表明，催化剂虽具有较高的起始活性，但随反应进行，活性有所下降，30?h后基本保持稳定，甲醇转化率和产氢率分别为73％和66％，产物湿基组成中H2和CO的质量分数分别为>55％和0.07%～0.08%。该类催化剂的反应稳定性虽较差，但却可以显著降低产物湿基组成中CO的摩尔分数。对LDHs前驱体制备的催化剂进行XRD和SEM表征结果表明，ZrO2的加入使催化剂中CuO晶粒分散更为均匀，颗粒更细。     

Ni-Al layered double hydroxides electrodeposition from a chloride solution

Ni-Al LDHs was electrodeposited from a NiCl₂-AlCl₃ solution. In order to analyze the electrodeposition process, electrolytes with initial Al content range of 0–20% were used. With increasing Al content in the sample, the preferred orientations of (0 0 3) and (0 0 6), increased crystallinity, and decreased interlayer spacing were observed from the XRD results. A dissolution–recrystallization of (0 0 3) plane was detected among the Ni-Al LDHs from the strongly alkaline solution soaking results, which was found to be conducted easily in high Al-containing samples. The pH of the Al-containing electrolyte was much lower than that of pure NiCl₂ solution because lower pH was needed to start a precipitation reaction in the AlCl₃-NiCl₂ solution. The electrodeposition yield and current efficiency were found to decrease obviously in the electrolytes with initial Al content higher than 10%, which was attributed to the increasing Al content in the sample and diffusion of the complex ions. The electrodeposition pattern was in-situ in the electrolyte initially containing 10% Al, then, it developed toward and off in-situ in electrolytes initially containing 0–10% and 10–20% Al.     

超分子结构二氟尼柳插层镁铝水滑石的合成与表征

采用离子交换和共沉淀两种不同方法将二氟尼柳插入镁铝水滑石层间，得到一种新型的有机-无机层状复合材料。通过X射线粉末衍射、红外光谱、元素分析和热重-差热等手段对材料进行了表征。结果表明，离子交换法和共沉淀法成功地将二氟尼柳插入水滑石，得到的材料层状结构完整、晶相单一，且层间距均大于二氟尼柳分子尺寸，扩大为1.81～2.14 nm；二氟尼柳插入后，复合水滑石材料的热稳定性大幅度提高。客体二氟尼柳与主体层板之间存在超分子作用力，二氟尼柳分子的羧基与水滑石层板之间相互作用，以双层倾斜交替地排列于层板之间。此外，根据其超分子作用力建立了二氟尼柳插层镁铝水滑石的超分子结构模型。     

A Prospect for Environmental Remediation of Perchlorate via Cost-Effective Pinus Leaves and Dandelion Flower Powder-based Layer Double Hydride (LDH) Sorbents

In this study, pine leaves powder (PiP) and dandelion flower powder (DFP) were repurposed to synthesize layered double hydroxides (LDHs) to form a base for sorbents used in perchlorate remediation from wastewater. The effects of the adsorbent dose, pH, thermodynamics, and coexisting ions were evaluated in batch experiments. The results revealed that 0.1 g adsorbent (PiP-LDH and DFP-LDH) removed 97% and 93% of perchlorate contaminants, respectively. In this study, the correlation coefficient of pseudo-second-order was higher than pseudo-first-order for all the LDHs. The kinetic and isotherm studies showed the best uptake of perchlorate in the short time was by PiP-LDH, followed by DFP-LDH (20 min and 40 min, respectively). The calculated and experimental values of adsorption at the equilibrium state also concurred with the pseudo-second-order model. The prepared LDHs were mesoporous. The surface area of PiP-LDH provided more adsorption sites, rendering it more suitable for perchlorate adsorption compared with the other two LDHs. The model suggests Physico-chemical interactions behind the sorption of perchlorate by LDHs. The adsorption was more influenced by anions i.e, PO₄³⁻ > SO₄²⁻ > NO₃ than monovalent anions due to the increase in the charge radius values. The prepared LDHs could be of great benefit to the environmental remediation of wastewater bodies.     

层状双金属氢氧化物Zn(Cu)/Al-LDHs的制备及其光催化还原二氧化碳的研究

用共沉淀法制备了不同M2+/M3+的层状双金属氢氧化物Zn(Cu)/Al-LDHs,利用粉末X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外可见漫反射(UV-Vis DRS)以及热重分析仪(TG-DSC)等测试方法表征了所制备样品的结构、形貌以及相关物性.在自行设计的催化反应系统中于室温和常压下测试了催化剂光催化还原CO2(g)+H2O(g)的活性.结果表明所制备的Zn(Cu)/Al-LDHs样品均可光催化还原CO2(g)+H2O(g),实验中测得的催化反应产物主要是CO和CH4.LDHs结构中Cu2+对Zn2+的取代导致催化剂吸收边红移,并显著提高催化反应产率.     

Ni/Zn/Cr系复合金属氧化物的制备及其光催化还原二氧化碳性能研究

以共沉淀法合成的Ni/Zn/Cr系层状金属氢氧化物(LDHs)经不同温度焙烧获得相应的复合金属氧化物,利用XRD、TG、XPS、TEM、BET和UV-Vis等表征手段对所制备样品的结构、组成、形貌以及吸光特性等进行了分析,并考察了样品在常温常压下光催化还原CO2(g)+H2O(g)的性能.结果表明,以Ni/Zn/Cr-LDHs为前驱体经5 00℃焙烧后可得到晶粒尺寸小、分散均匀度高的多相复合金属氧化物,主晶相为纳米尺度的NiO、Cr2O3、ZnCr2O4和NiCr2O4,在这些金属氧化物的协同作用下,样品表现出较好的光催化还原二氧化碳活性,主产物为CH4和CO.     

Structure and photoluminescence of Mg-Al-Eu ternary hydrotalcite-like layered double hydroxides

A series of Mg-Al-Eu ternary hydrotalcite-like layered double hydroxides (LDHs), with Eu/Al atomic ratios of ∼0.06 and Mg/(Al+Eu) atomic ratios ranging from 1.3 to 4.0, were synthesized by a coprecipitation method. The Mg-Al-Eu ternary LDHs were investigated by various techniques. X-ray diffraction (XRD) results indicated that the crystallinity of the ternary LDHs was gradually improved with the increase of Mg²⁺/(Al³⁺+Eu³⁺) molar ratio from 1.3/1 to 4/1, and all the samples were a single phase corresponding to LDH. The photoluminescent (PL) spectra of the ternary Mg-Al-Eu LDHs were described by the well-known ⁵D₀-⁷F_J transition (J=1, 2, 3, 4) of Eu³⁺ ions with the strongest emission for J=2, suggesting that the host LDH was favorable to the emissions of Eu³⁺ ions. The asymmetry parameter (R) relevant to ⁵D₀-⁷F_J transition (J=1, 2) dependant of the atomic ratios of Mg²⁺/(Al³⁺+Eu³⁺) was discussed, and was consistent with the result of XRD.     

杂多阴离子柱撑水滑石层柱相互作用的XPS研究(II)

水滑石（LayeredDoubleHydroxides，简称LDHs）作为一类重要的柱层材料已引起人们的重视[1，2]．人们利用水滑石间柱阴离子的可交换性的特点[3].将各种阴离子如无机和有机阴离子[4]、同多和杂多阴离子（Polyoxometalates；简称POMs）[5]相继被引入水滑石层间．因此得到了具有高