不同金属离子对CO／Al_2O_3中Co的分布和CoMoK／Al_2O_3催化

在γ－Ａｌ２Ｏ３中加入Ｚｎ２＋，Ｍｇ２＋，Ｃｕ２＋或Ｃｒ３＋后用漫反射光谱法研究了它们对随后加人的Ｃｏ分布的影响，同时还研究了这些离子对水煤气变换反应催化剂ＣｏＭｏＫ／Ａｌ２Ｏ３的催化活性的影响．发现Ｚｎ２＋，Ｍｇ２＋具有阻止Ｃｏ进入载体内层的作用，Ｃｕ２＋，Ｃｒ３＋的作用则相反．四面体配位倾向强的金属离子能阻止Ｃｏ进入载体内层，从而促进水煤气变换反应的催化活性，而八面体配位倾向强的金属离子的效果刚好相反．在６５０℃下，１００ｇＡｌ２Ｏ３含７ｇＭｇＯ时，Ｍｇ能最大限度地阻止Ｃｏ向Ａｌ２Ｏ３内层扩散，从而提高了ＣｏＭｏｋ／Ａｌ２Ｏ３的催化活性．     

不同金属离子对Co/Al2O3中Co的分布和CoMoK/Al2O3催化活性的影响

在γ－Ａｌ２Ｏ３咖入Ｚｎ＾２＋，Ｍｇ＾２＋，Ｃｕ＾２＋或Ｃｒ＾３＋后用漫反射光谱法研究了它们对随后加入的Ｃｏ分布的影响，同时还研究了这些离子对水煤气变换反应催化剂ＣｏＭｏＫ／Ａｌ２Ｏ３的催化活性的影响，发现Ｚｎ＾２＋，Ｍｇ＾２＋具有阻止Ｃｏ进入载体内层的作用，Ｃｕ＾２＋，Ｃｒ＾３＋的作用则相反，四面体配位倾向强的金属离子能阻Ｃｏ进入载体内层，从而促进水煤气变换反应的催化活性，而八面配位倾向强度金属     

以水滑石为前体的Mg-Al-M复合氧化物对催化消除NOx的活性

通过Ｈ２ＴＰＲ,ＸＲＤ,ＴＧＤＴＡ及比表面积测定等对ＭｇＡｌ水滑石化合物进行了表征,研究了焙烧温度对水滑石物理性质的影响．在此基础上,研究了ＭｇＡｌ水滑石中加入过渡金属（Ｍ）离子后对ＮＯ＋ＣＯ反应的催化活性．结果发现,含有Ｃｕ离子的样品对ＮＯ＋ＣＯ反应有较高的催化活性,并与ＣｏＡｌＭ的催化性能进行了比较     

以水滑石为前体的Mg—Al—M复合氧化物对催化消除NOx的活性

通过Ｈ２－ＴＰＲ、ＸＲＤ，ＴＧ－ＤＴＡ及比表面积测定等对Ｍｇ－Ａｌ水滑石化合物进行了表征，研究了焙烧温度对水滑石物理性质的影响，在此基础上，研究了Ｍｇ－Ａｌ水滑石中加入过渡金属（Ｍ）离子后对ＮＯ＋ＣＯ反应的催化活性。结果发现，含有Ｃｕ离子的样品对ＮＯ＋ＣＯ反应有较高的催化活性，并与Ｃｏ－Ａｌ－Ｍ的催化性能进行了比较。     

甲烷部分氧化制合成气Ⅱ．镍系催化剂的反应性能

主要用第四周期金属元素的氧化物与Ａｌ２Ｏ３的复合氧化物催化剂上甲烷氧化的结果证实了催化剂设计中的预测：（１）催化剂首先应能解离活化甲烷，（２）催化剂要能较快地活化Ｏ２分子．只有同时满足这两个条件，催化剂才可能有较好的甲烷部分氧化活性．第四周期元素中只有镍具有这样的性质．Ｃｕ，Ｍｎ，Ｃｒ，Ｌａ，Ｃａ，Ｚｎ等氧化物的添加可明显提高Ｎｉ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能，其中Ｃｕ的助催化性能最好．催化剂ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３，ＮｉＯ－ＭｎＯ－Ａｌ２Ｏ３，ＮｉＯ－Ｃｒ２Ｏ３－Ａｌ２Ｏ３的反应活性和选择性顺序，与金属Ｃｕ，Ｍｎ，Ｃｒ上ＣＯ和Ｈ２脱附的顺序是一致的     

ELECTRON TRANSFER BETWEEN Eu~(3+) AND Ce~(3+) IN SrMgF_4 MATRIX

ＥＬＥＣＴＲＯＮ　ＴＲＡＮＳＦＥＲ　ＢＥＴＷＥＥＮ　Ｅｕ~（３＋）　ＡＮＤ　Ｃｅ~（３＋）　ＩＮ　ＳｒＭｇＦ_４　ＭＡＴＲＩＸＥＬＥＣＴＲＯＮＴＲＡＮＳＦＥＲＢＥＴＷＥＥＮＥｕ~（３＋）ＡＮＤＣｅ~（３＋）ＩＮＳｒＭｇＦ_４ＭＡＴＲＩＸ￥ＹｉｎｇＷＵ；Ｃｈ...     

超高比表面炭载钼煤气甲烷化催化剂

以沥青中间相为原料，氢氧化钾直接活化，获得了比表面达２３６３ｍ￣２／ｇ的超高比表面炭分子筛（ＣＭＳ）。分别以ＣＭＳ、ＳｉＯ＿２、活性炭和θ－Ａｌ＿２Ｏ＿３为担体，制备了负载钼催化剂，并研究其加压甲烷化反应性能，发现活性依下面顺序增加：θ－Ａｌ＿２Ｏ＿３＜ＳｉＯ＿２＜活性炭（ＡＣ）＜ＣＭＳ。还分别以钼酸铵和磷钼酸（ＨＰＭｏ）为前驱体，制备了ＣＭＳ负载钼催化剂，并考察了其煤气甲烷化活性，发现不同的催化剂前驱体对催化剂反应活性影响很大。根据产物中ＣＨ＿４／ＣＯ＿２的变化，推测ＣＯ在钼催化剂上的甲烷化反应包括如下两个步骤：（１）３Ｈ＿２＋ＣＯ→ＣＨ＿４＋Ｈ＿２Ｏ，（２）ＣＯ＋Ｈ＿２Ｏ→ＣＯ＿２＋Ｈ＿２。     

甲烷部分氧化制合成气Ⅳ．镍铜催化剂的反应性能及影响因素的考察

对镍铜甲烷部分氧化催化剂的制备化学研究表明，在Ａｌ２Ｏ３、ＳｉＯ２、ＭｇＯ、ＴｉＯ２、Ｙ型分子筛等载体中，具有较好氢溢流功能的Ａｌ２Ｏ３所担载的镍铜催化剂，有最佳的反应性能，载体的产物溢流功能对反应中合成气的生成是有利的．对于ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂，组分Ｃｕ的最佳含量是Ｃｕ／Ａｌ＝０．２／４（原子比），Ｎｉ／Ａｌ（原子比）在１／４－１．５／４范围内催化剂均保持最佳的反应性能，此时，甲烷转化率为９８．１％，对ＣＯ、Ｈ２的选择性分别达９７％、１００％．制备方法对催化性能影响的结果显示，以（ＮＨ４）２ＣＯ３为沉淀剂的共沉淀法，是制备ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的最佳方法．ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能在４００－５００℃间有一突跃，并在７００℃时达到最佳值；过高的反应气空速对ＣＯ、Ｈ２的选择性是不利的     

PTFE-乙醚柱反相萃取层析连续分离和测定镓(Ⅲ)铟(Ⅲ)的研究

研究了在抗坏血酸存在下的６ｍｏｌ／ＬＨＢｒ介质作流动相，以ＰＴＦＥ（聚四氟乙烯）负载的乙醚作固定相，反相萃取层析使微量Ｇａ（Ⅲ）、Ｉｎ（Ⅲ）与Ｆｅ３＋、Ｔｌ３＋、Ｍｏ６＋、Ａｕ３＋、Ｔｉ４＋、Ｂｉ３＋、Ａｌ３＋、Ｍｇ２＋、Ｃａ２＋、Ｎｉ２＋、Ｃｏ２＋、Ｃｄ２＋、Ｚｎ２＋、Ｐｂ２＋、Ｃｕ２＋等多种离子分离。留于柱上的铟、镓分别用ＨＣｌ（４ｍｏｌ／Ｌ）－Ｈ２Ｏ２（３％）及ＨＢｒ（１ｍｏｌ／Ｌ）洗脱进行连续分离与测定。本方法已应用于地质样品中微量镓、铟的连续分离与测定     

笼形聚偕氨肟树脂的研究：酸处理树脂的吸附性能

笼形聚偕氨肟树脂（ＣＡＯ）经盐酸处理垢，伯胺基转变成胺盐。酸处理笼形聚偕氨肟树脂（ＡＣＡＯ）对Ｍｇ＾２＋，Ｃａ＾２＋，Ｂａ＾２＋，Ｍｎ＾２＋，Ｃｏ＾２＋，Ｎｉ＾２＋离子不吸附；对Ｚｎ＾２＋，Ｃｄ＾２＋，Ｃｕ＾２＋，Ｐｂ＾２＋离子的吸附效率在２０％以下，但对Ｈｇ＾２＋离子的吸附效率则高达７１．２％；对一些金属络阴离子的吸附效率顺序是Ｆｅ（ＣＮ）＾２－６＞Ｃｒ２Ｏ＾２－７＞ＭｏＯ＾２－４＞ＰｔＣｌ＾２     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.