单分散、大粒径聚苯乙烯微球的制备

以聚乙烯基吡咯烷酮为分散剂、偶氮二异丁腈为引发剂、醇／水混合物为分散介质进行了苯乙烯的分散聚合，讨论了初始单体浓度、分散剂用量、引发剂浓度、分散介质组成和反应温度等反应条件对所得聚合物颗粒直径和直径分布的影响．通过大量的试验，筛选出了较为理想的分散聚合的条件及配方，制备出了粒径为４８μｍ的单分散聚苯乙烯微球．然后，以分散聚合所制得的聚合物颗粒为种子，用动力学溶胀法制成了粒径增大近四倍的单分散、大粒径聚苯乙烯微球，并讨论了滴水速度和补加分散剂对溶胀的影响     

紫外光引发丙烯酰胺分散聚合研究

以聚丙烯酸接枝壬基酚聚氧乙烯(PAA -g -NPEO)作分散剂,紫外光(UV)引发丙烯酰胺(AM )在叔丁醇 水(TBA /H2 O)体系中进行了分散聚合.考察了聚合反应特征以及醇水比、初始单体浓度、引发剂浓度、分散剂浓度、表面入射光强、反应温度、液层厚度等参数对聚合产物粒径及分子量的影响.结果表明该聚合体系不存在诱导期,反应速度快,光照4 0min转化率可达到90 % ,产物分子量达6 . 5×10 6 .透射电镜(TEM)观察显示所得聚合物粒子基本为球形,粒径分布较为均匀.     

分散聚合法制备PVP微球的研究

以N-乙烯基吡咯烷酮(NVP)为初始单体,乙酸乙酯为分散介质,采用分散聚合法制备了分散性能良好、粒径为3～4μm的聚乙烯基吡咯烷酮(PVP)微球.考察了单体、分散剂及引发剂浓度对PVP微球的粒径、单体转化率及分子量的影响,并对PVP的结构和性能进行研究.结果表明,单体浓度增加,PVP微球粒径和分子量增大,单体转化率升高;分散剂浓度增加,PVP微球粒径变小,分子量增大,单体转化率升高;引发剂浓度增加,PVP微球粒径变大,分子量减小,单体转化率升高.与溶液聚合法相比,分散聚合法制备的PVP分子量较小且具有一定的结晶性.     

乙酸乙酯/乙醇混合溶液中分散聚合制备单分散亚微米级聚丙烯酰胺微球

以乙酸乙酯/乙醇混合溶液为分散介质, PVP为分散剂, 通过分散聚合法合成了单分散亚微米级PAM微球. 在反应初期, 自动加速现象明显. 由于凝胶效应的影响, 分子量随着单体转化率的提高而逐渐增大. 考察了分散剂浓度对最终产物增率的影响, 并用IR光谱对产物的结构进行了表征, 证明分散聚合体系中吸附稳定机理和接枝稳定机理同时存在, 且以后者为主. 同时还研究了混合溶剂比例、分散剂浓度、初始单体浓度和引发剂浓度对微球粒径及粒径分布的影响. 结果表明, 乙酸乙酯/乙醇体积比在5∶5-7∶3范围内, 可得到粒径在200 nm左右, 且分布较窄的PAM微球; 分散剂浓度增大, 粒径减小; 引发剂浓度增加, 粒径增大; 初始单体浓度较高或较低时, 都得不到单分散性微球.     

单分散,大为闰径聚苯乙烯微球的制备

以聚乙烯基吡咯酮为人发散剂，偶氮二异丁腈为引发剂、醇／水浊给物为分散介质进行了苯乙烯的分散聚合，讨论了初始单体浓度，分散剂量用、引发剂浓度、分散介质组成和反应温度等反应条件对所得聚合物颗粒直径和直和戏分布的影响。     

纳米铬粉的制备研

以ＣrＣ１３为原料,三乙基硼氢化钠为还原剂,聚乙烯吡咯烷酮为分散剂,ＰdＣ１２为成核剂,于甲苯溶剂中制备出平均粒径约５０ｎｍ的铬粉,反应温度、反应物浓度、分散剂与成核剂的添加是影响粒径的主要因素。同时探讨了反应的机理与铬粉的热稳定性。     

分散聚合法制备窄分子量分布的聚苯乙烯微球

以无水乙醇为反应介质,以聚乙烯吡咯烷酮(PVP)为分散剂,偶氮二异丁腈(AIBN)为引发剂,采用分散聚合法制备分子量分布较窄的聚苯乙烯(PS)微球。研究了反应温度及反应时间、引发剂浓度和单体浓度对苯乙烯转化率和PS分子量分布的影响,采用SEM、GPC、FT-IR和TG对产物的形貌、分子结构和性能等进行了表征。结果表明:单体浓度为20%,引发剂用量为单体总量的0.7%,75℃下反应13h后,聚合反应的单体转化率可达87.8%,所制得的PS球形度较好,重均分子量为16.6万,分子量分布1.21,且具有优异的热稳定性。     

单分散PS/PAA聚合物微球的研制

以苯乙烯为单体,采用分散聚合法制备了单分散性的聚苯乙烯(PS)微球,然后以PS微球作为种子、丙烯酸(AA)进行无皂种子乳液聚合制备了PS／PAA微球。考察了单体、引发剂、分散剂用量,反应介质极性和交链剂等因素对微球粒径大小及其分布的影响,探讨了分散聚合的反应机理。结果表明,通过改变反应工艺条件,能够制备粒径为1．0～3．0μm、单分散性很好的PS微球;通过无皂种子乳液聚合得到的核壳结构的PS／PAA微球粒径为2．50μm,多分散系数(PI)为0．0325,酸值为10．27mgNaOH／g,其表面带有羧基的特性能进一步扩大应用范围。     

部分析因设计法优化分散聚合制备单分散种子微球

采用分散聚合法,以正丁醇为分散介质、苯乙烯为单体、聚乙烯吡咯烷酮(PVP)为分散剂、偶氮二异丁腈(AIBN)为引发剂,制备单分散聚苯乙烯微球作为色谱填料的种子。实验以微球的平均粒径为主要考察指标,以GSD为次要考察指标,通过部分析因设计,获得了粒径为10μm的单分散(GSD=1.06)微球。     

碳酸钙在St-MMA悬浮聚合中的应用研究

以碳酸钙为分散剂,过氧化二苯甲酰为引发剂,采用悬浮聚合法合成苯乙烯-甲基丙烯酸甲酯共聚物。研究了碳酸钙用量、反应温度、反应时间、引发剂用量、水与单体体积比、苯乙烯与甲基丙烯酸甲酯体积比对悬浮聚合的影响。结果表明,碳酸钙用量为2.0~3.0g,反应温度为75~80℃,反应时间为3h,引发剂用量为0.3115g,水与单体体积比为5:1~7:1,苯乙烯与甲基丙烯酸甲酯体积比为1/8.5~1:1(单体总体积为9.5m L)时,制得的共聚物颗粒大小均匀,粒径在0.31mm~0.60mm,产率在90%以上。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.