Elemental analysis of particulate matter in a metal workshop and of biological samples from exposed workers

During metal welding and cutting, large amounts of particulate matter (PM) are produced that might represent a significant health risk for the exposed workers. In the present pilot study, we performed an elemental analysis of fine PM collected in a metal workshop. Also, elemental analysis of the hair and nail samples collected from workers exposed to the workshop dust and control group was done. Concentrations of 15 elements in PM were measured with X‐Ray Fluorescence (XRF) and Particle Induced X‐ray Emission (PIXE), whereas inductively coupled plasma mass spectrometry (ICP‐MS) was used to determine 12 elements in hair and nail samples. Mean 8‐hr concentrations of PM_2.5, Fe, and Mn in the vicinity of welders were up to 1803, 860, and 30 μg/m³, respectively, whereas in the nearby city, daily PM_2.5 concentrations are on average 11 μg/m³. We found that several elements, especially Fe and Mn, had substantially higher concentrations in hair and nail samples of exposed workers than in the control group, which indicates the accumulation of metals in workers' tissues, although limit values were not exceeded.     

Steep Points of Gaussian Free Fields in Any Dimension

Journal of Theoretical Probability - This work aims to extend the existing results on the Hausdorff dimension of the classical thick point sets to a more general class of exceptional sets of a...     

Multi-scale finite element simulation on large deformation behavior of wood under axial and transverse compression conditions

Acta Mechanica Sinica - Multi-scale finite element method is adopted to simulate wood compression behavior under axial and transverse loading. Representative volume elements (RVE) of wood...     

Lower Bounds for the Robustness of Multilevel Coherence

International Journal of Theoretical Physics - Quantum coherence, coming from quantum superposition, occupies a significant position in the field of physics. We put forward a lower bound of the...     

污泥基吸附剂对亚甲基蓝和环丙沙星的吸附性能研究

亚甲基蓝和环丙沙星是水体中2种污染物, 对生态环境有潜在危害. 本文以市政剩余活性污泥为原料, 氯化锌为活化剂热解制备污泥基吸附剂, 研究盐酸酸洗浓度、氯化锌浓度、热解温度、热解时间等对污泥基吸附剂吸附水中亚甲基蓝和环丙沙星性能的影响. 结果表明 (1)污泥基吸附剂对亚甲基蓝的吸附性能随盐酸酸洗浓度的增大而增加, 对环丙沙星的吸附性能则随盐酸酸洗浓度的增大呈先降后增趋势, 两者均在1.500mol·L-1盐酸浓度下取得最优值. (2)污泥基吸附剂对亚甲基蓝和环丙沙星的吸附性能随氯化锌浓度和热解温度的增加呈先升后降趋势, 在氯化锌浓度为4.0mol·L-1、热解温度为500℃时有最优值; 随着热解时间的延长, 污泥基吸附剂对亚甲基蓝和环丙沙星的吸附性能分别在500℃热解70min和80min时有最优值. (3)污泥基吸附剂的最佳制备条件为 氯化锌4.0mol·L-1活化2h、500℃热解70min和80min、1.500mol·L-1盐酸酸洗; 以此制得的污泥基吸附剂对亚甲基蓝和环丙沙星的去除率分别为97.7%和96.4%, 平衡吸附量分别为97.9mg·g-1和3.9mg·g-1, 且污泥基吸附剂对亚甲基蓝和环丙沙星的吸附过程均符合准二级动力学方程.     

A visual uncertainty analytics approach for weather forecast similarity measurement based on fuzzy clustering

Journal of Visualization - Forecast calibration methods based on historical similar atmospheric state are effective means weather forecast accuracy. Conventional approaches search similar forecasts...     

砂土串囊式充气锚杆承载力的研究

在砂土地层中,串囊式充气锚杆的研究还比较少,其承载特性及受力机理尚不明确。本文基于莫尔-库仑模型和Vesic圆孔扩张理论法,分别对圆柱体、球体、组合体、椭球体假设下的串囊式充气锚杆的扩大段进行计算分析。并将计算结果与试验得到的实测值进行对比。结果表明:四种形状假设中椭球体的形状假设理论值与实测值的误差最小,仅为8.35%。通过拟合试验数据,并引入与端阻力和侧摩阻力有关的两个系数对承载力公式进行修正,得到了抗拔承载力的经验公式。     

Rigidity and stability of submanifolds with entropy close to one

Geometriae Dedicata - We show that an n-dimensional surface whose entropy is close to that of an n-dimensional plane is close in Hausdorff distance to some n-dimensional plane at every scale....     

Good polynomials for optimal LRC of low locality

Designs, Codes and Cryptography - According to a magnific method due to I. Tamo and A. Barg, a class of polynomials over finite fields, called good polynomials, was introduced and used to construct...     

Development of an improved divergence‐free‐condition compensated coupled framework to solve flow problems with time‐varying geometries

In this article a coupled version of the improved divergence‐free‐condition compensated method will be proposed to simulate time‐varying geometries by direct forcing immersed boundary method. The proposed method can be seen as a quasi‐multi‐moment framework due to the fact that the momentum equations are discretized by both cell‐centered and cell‐face velocity. For simulating time‐varying geometries, a semi‐implicit iterative method is proposed for calculating the direct forcing terms. Treatments for suppressing spurious force oscillations, calculating drag/lift forces, and evaluating velocity and pressure for freshly cells will also be addressed. In order to show the applicability and accuracy, analytical as well as benchmark problems will be investigated by the present framework and compared with other numerical and experimental results.