The system of L-band 2×10 Gb/s WDM transmission over conventional single mode fibre with 600 km by chirped fibre Bragg gratings dispersion compensation

A chirped fibre Bragg grating according to ITU-T suggested L-band (2nd channel $\lambda _{1}=1570.83$~nm; 80th channel $\lambda _{2}=1603.57$ nm) with more than 1800 ps/nm single channel dispersion compensation is presented in this paper, of which the cladding mode loss, the delay curve ripple and the power fluctuation of the reflected spectrum are less than 0.5 dB, 50 ps and 0.25 dB, respectively. With this new FBG as dispersion compensation device, a $2\times 10$ Gb/s wavelength division multiplexing (WDM) L-band transmission of 600 km based on conventional single mode fibre (G.652 fibre) is performed without forward error correction. The bit error rate (BER) is less than 10$^{ - 12}$ and the power penalties of the 2{nd} and 80{th} channel of L-band are 1.8~dB and 2.0~dB, respectively.     

Polarization-maintaining photonic crystal fibre

Photonic crystal fibres (PCFs) offer new possibilities of realizing highly birefringent fibres due to a higher intrinsic index contrast compared to conventional fibres. In this paper, we analyse theoretically the modal properties of a kind of polarization-maintaining PCF, namely the elliptical hole photonic crystal fibre (EHPCF) with a central small elliptical hole introduced in the core region. We demonstrate the possibility of achieving large birefringence with zero walk-off in the single-mode regime. This PCF also exhibits unusual dispersion properties. Several hundred nanometres of ultra broadband flattened dispersion near the wavelength 1.55μm is achieved in this EHPCF with a central small hole of d_c=0.4Λ.     

Suppression of the interactions between fibre gratings used as dispersion compensators in dense wavelength-division multiplexing systems

Chirped fibre Bragg gratings (CFBGs) are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing (DWDM) systems. When the channel spacing is small, the performance of CFBGs is degraded, which restricts the usage of fibre gratings. The origin of the interactions between the gratings is analysed and methods of suppressing the interactions are also proposed.     

基于增强瑞利反馈的单模窄线宽随机激光器

仿真说明了单模光纤(SMF)中瑞利散射(RS)的机理, 指出纤芯掺杂的不均匀性以及拉丝过程引起的光纤几何尺寸的随机变化是光纤中RS产生的主要原因, 并以此为基础制作了损耗为0.54 dB/km的散射光纤. 在通信波段, 5 km该散射光纤的瑞利背向散射(RBS)强度高于相同长度的SMF-28近5 dB. 在基于RBS单模随机激光器的数值模拟中, 大量的具有随机幅度和相位的纵模在经历不平坦增益的多次放大之后, 只有在增益最大点附近的模式能够克服损耗成为输出模式. 实验中以掺铒光纤作为增益介质, 500 m散射光纤提供随机反馈, 窄带布拉格光纤光栅(FBG)作为波长选择器件, 得到线宽约3.5 kHz、对比度近50 dB的单模激光输出. 与采用相同长度SMF-28的随机激光器相比, 其阈值电流降低了80 mA, 相同抽运条件下的最大输出功率提高了3 dBm. 该单模窄线宽随机激光器的输出波长的调谐特性仅由FBG的中心波长决定.     

类矩形芯光子晶体光纤的色散与偏振特性

应用全矢量模型分析类矩形芯光子晶体光纤的色散和偏振特性，讨论了光纤结构参数对光纤特性的影响.研究表明：类矩形芯光子晶体光纤的模式双折射比普通椭圆保偏光纤至少高一个数量级.增大光纤的相对孔径，可获得更高的双折射.零走离点对应的波长也比普通椭圆保偏光纤长，随着孔距的增大，走离曲线将向长波长方向产生移位，零走离点发生红移，零走离点所对应的波长与孔距成正比.零走离点的出现，将有效地抑制一阶偏振模色散.通过调整光纤的结构参数，可以获得灵活的色散特性，在孔距Λ=2μm, 相对孔径d/Λ=03时，在波长155μm附近，获得近400nm的超平坦色散区.该光纤在偏振控制、色散控制和管理方面具有广泛的应用前景. 关键词： 导波光学 光子晶体光纤 类矩形芯 全矢量     

Novel modal interferometer based on ring-core photonic crystal fiber

An original design of ring-core photonic crystal fiber （RPCF） is proposed. By splicing a section of the homemade RPCF between two segments of single mode fibers （SMFs）, a simple modal interferometer is presented and experimentally demonstrated. Owing to the effects of the collapsed region, the ring modes in RPCF can be effectively activated. To our knowledge, it is the first time to demonstrate the modal interferometer based on the interference between the ring modes, which is different from the previously reported interferometers based on the interference between core modes or cladding modes. The temperature and strain characteristics of the interferometers with different lengths of RPCF are investigated.     

多层光纤布拉格光栅的理论与实验研究

从理论和实验两方面研究了在非周期性多层光纤上写入布拉格光栅的光学特性。从耦合模理论出发,讨论了光纤具有多于一个光敏层的情况。在实验室自制的两类多层光纤上写入光栅的实验也表明,该类光栅具备有一般光栅的普遍光学特性,说明在使用多层光纤作为关键部分构建器件时,需要的各类光栅部件能够通过直接在该类光纤上写入光栅实现。紫外光在氢载掺铒多层光纤上写入光栅的实验说明分层的异种元素掺杂将导致芯区应力增加,从而辅助提高光纤的光敏性。     

具有复介电常量二维光子晶体的特性研究

采用平面波展开法,通过数值模拟研究了具有复介电常量的二维光子晶体的能带结构和光传输特性,重点讨论介电常量的虚部为负值情形时对传输特性的影响。研究表明由于光子带隙的存在有效地抑制了频率位于带隙内光的自发辐射。当在介质中掺入具有增益特性的杂质时,即使两种介质的介电常量相差很小,在靠近光子带隙边缘,出现了较强的受激辐射放大。通常在带隙的边缘处,光子晶体的群速度较小,而激光阈值正比于群速度的平方,当群速度很小时,激光阈值将大大减小。这为实现零阈值激光器提供了基础,也为制作光放大微器件提供了一个有益的理论参考。     

折射率导模高双折射光子晶体光纤

与传统光纤相比,光子晶体光纤芯区与包层之间具有更高的折射率差,并且制作过程中可以灵活地制造各种对称与非对称结构,这为在光子晶体光纤中实现高双折射提供了可能。应用全矢量模型分析一种折射率导模高双折射光子晶体光纤,其包层采用两种尺寸的空气孔,使该光纤具有二重旋转对称性,原来简并的两个正交偏振模不再简并,呈现出较高的双折射,模式双折射比普通的保偏光纤高至少一个量级。分析结果表明,在波长1540nm,其拍长可达0．4067mm。理论分析结果与实验测量结果相吻合。     

熊猫型保偏光纤中应力区失配对光纤性能影响的研究

采用弹性力学理论和复变函数法导出了熊猫型保偏光纤应力双折射的近似解析表达式.利用有限元法数值分析了熊猫型保偏光纤的双折射特性,结果表明,与采用纤芯中心应力相比,采用芯区平均应力表示光纤的双折射较为精确,且结果与解析法导出的芯区中心应力双折射计算结果相比误差小于0.18%.在此基础上进一步分析了应力区失配对熊猫型保偏光纤的双折射所产生的影响,并通过实验测试证明了分析结果的正确性. 关键词： 偏振保持光纤 应力区失配 双折射 拍长