利用Cramér-Rao理论研究相位差法的最佳离焦量

针对光子数足够多的情况,利用Cramér-Rao理论研究了在选取离焦作为附加像差时,不同的待测波前和目标对最佳离焦量选取的影响。结果表明:在点目标情况下,像差的大小和空间频率对最佳离焦量的影响不大;而在扩展目标情况下,最佳离焦量虽然与待测像差的空间频率关系不明显,但随着待测像差峰谷值的增大而增大。最佳离焦量与目标的结构有关而与其扩展程度关系不大,成像时目标上各点的干扰越大,最佳离焦量越大。     

The effect of laser peak power and pulse width on the hole geometry repeatability in laser percussion drilling

In this work, the two main factors that influence the repeatability of the laser percussion drilling process are identified. Experimental parametric analysis was carried out to correlate the laser parameters with the repeatability of a laser percussion drilling process. The experiment was conducted using a flash lamp pumped Nd:YAG laser to drill 2 mm thick mild steel sheets. The relationship between the percentage standard deviation (PSD) of entrance hole diameter, hole circularity and the operating parameters is established. Thirty-five holes were drilled and analysed for each set of identical laser parameters. The PSD of entrance hole diameter ranges between 1.47% and 4.78% for an operating window of 3.5–7 kW peak power, and 1–3 ms pulse width. The circularity of the entrance hole (defined as the ratio between the minimum and maximum diameters of the hole) ranges from 0.94 to 0.87, and is found to correlate with repeatability. The work shows that higher peak power, and shorter pulse width gives better hole geometry repeatability. The effect of melt ejection on hole geometry repeatability is also investigated. Melt ejection and spatter formation have been found to contribute to the poor repeatability of the process.     

Molecular dynamics simulations of jet breakup and ejecta production from a grooved Cu surface under shock loading

Large-scale non-equilibrium molecular dynamics simulations are performed to explore the jet breakup and ejecta production of single crystal Cu with a triangular grooved surface defect under shock loading. The morphology of the jet breakup and ejecta formation is obtained where the ejecta clusters remain spherical after a long simulation time. The effects of shock strength as well as groove size on the steady size distribution of ejecta clusters are investigated. It is shown that the size distribution of ejecta exhibits a scaling power law independent of the simulated shock strengths and groove sizes. This distribution, which has been observed in many fragmentation processes, can be well described by percolation theory.     

对风沙输运中起跳沙粒运动状态分布的讨论

本文用Lagrange方法结合起跳沙粒初始运动状态分布模拟了稳态风沙输运过程。根据已有的对地表沙粒撞击起跳现象的研究成果,列出四种典型的沙粒起跳初始运动状态分布形式。将在各分布形式下模拟得到的宏观量与风洞实验测量得到的宏观量的变化规律相比较,通过考察依据各分布形式所作数值模拟得到的风沙宏观运动的特征量与实验测量结果的一致程度,得到了其中较合理的分布形式。分析表明稳定风沙输运中起跳沙粒的初始速度和角度的分布曲线均应为一单调下降曲线,根据实验数据本文构造出由指数分布和正态分布组成的分段函数形式来描述这一曲线。并通过进一步的实验验证了这一分布形式的合理性。     

太阳能固体吸附-喷射制冷联合循环系统研究

本文提出了一种新型太阳能固体吸附-喷射制冷联合循环系统,并建立了相应的物理模型.通过对系统运行原理和热力参数的分析与计算,认为该系统为解决太阳能固体吸附制冷系统的不连续性问题提供了一种行之有效的方法.同时,由于对吸附热的有效回收,系统的COP有一定的提高.     

印刷线路板分压离子阱的离子单向出射性能研究

印刷线路板(Printed-Circuit-Board,PCB)分压离子阱是一种新型质量分析器,其突出优点在于内部电场可通过调节射频分压比进行优化.本实验在PCB分压离子阱离子出射方向的两组离散电极上配置了非对称的射频分压,以引入奇次阶场成分,使得射频电场的场中心(即离子运动中心)发生偏移,从而实现离子单向出射.通过数值计算软件SIMION和AXSIM分析了射频分压比差值与其内部电场分布的关系,并模拟离子运动轨迹,得到离子出射情况和模拟质谱峰.模拟结果表明,当两组离散电极的射频分压比差值为20％时,在合适的AC频率条件下,对于m/z=609 Th的离子,PCB分压离子阱的离子单向出射率可达90％以上,且质量分辨率大于2500.本研究可使PCB分压离子阱在基本不损失质量分辨率和使用单检测器模式下,大幅提高离子检测效率,因而在小型化质谱仪应用中具有显著优势.     

Desorption of H ions from water chemisorbed on Si(100) by O 1s excitation - an Auger electron-photoion coincidence spectroscopy study

Auger electron-photoion coincidence (AEPICO) spectroscopy, which has been recently developed and proved to be a very powerful technique for investigating the dynamics of desorption induced by the core-level excitation, is applied to the investigation of Auger-stimulated ion desorption from the chemisorbed-water-Si(100) surface induced by O 1s excitation. It is shown that the fast relaxation of the excited state with a core hole and an excited electron takes place before the core hole decay, and that the desorption yield is enhanced by the shake-up (and/or shake-off) excitation. The relative cross-section for Auger-stimulated ion desorption is estimated, and is shown to increase as holes are created at deeper levels of the valence bands as the final state of the Auger decay. A comparison is also made with condensed H₂O.     

Atomic and electronic structure of the corundum (0001) surface: comparison with surface spectroscopies

The electronic structure and geometry of the Al-terminated corundum (0001) surface were studied using a slab model within the ab-initio Hartree-Fock technique. The distance between the top Al plane and the next O basal plane is found to be considerably reduced on relaxation (by 0.57 Å, i.e. by 68% of the corresponding interlayer distance in the bulk). An interpretation of experimental photoelectron spectra (UPS He I) and metastable impact electron spectra (MIES) is given using the calculated total density of states of the slab and the projections to the atoms, atomic orbitals, and He 1s floating atomic orbital at different positions above the surface. Calculated projected densities of states exhibit a strong dependence on the relaxation of surface atoms. The good agreement of simulated and experimental UPS and MIES spectra supports the correctness of calculated surface relaxation.     

动载荷下金属板表面的微物质喷射

 用石英晶体传感器技术，测量了冲击波作用下铝合金（Ly-12）和纯铅样品自由表面的微物质喷射量。在冲击压力为32 GPa时，测得光洁度为3.2、0.4、0.1 μm的铝合金的微物质喷射量分别为1.53～3.28 g/m²，0.2～0.3 g/m²和0.053～0.096 g/m²，对光洁度为3.2 μm的纯铅样品，在压力为13 GPa和47 GPa时，微物质喷射量分别微26.4～42.4 g/m²和183～328 g/m²。在最高冲击压力约为20 GPa时，做了多次冲击下的微物质喷射量测量，发现比单次冲击加载下的喷射量有很大的减少。结果表明，微物质喷射量与自由表面的加工条件、局部熔化和加载方式等因素有关。     

Tabu Search with Simple Ejection Chains for Coloring Graphs

We present a Tabu Search (TS) method that employs a simple version of ejection chains for coloring graphs. The procedure is tested on a set of benchmark problems. Empirical results indicate that the proposed TS implementation outperforms other metaheuristic methods, including Simulated Annealing, a previous version of Tabu Search and a recent implementation of a Greedy Randomized Adaptive Search Procedure (GRASP).