激光限制结晶技术制备nc-Si/SiO2多层膜

在等离子体增强化学气相淀积系统中，采用aSi:H层淀积和原位等离子体氧化相结合的逐层生长技术制备了aSi:H/SiO_2多层膜.在激光诱导限制结晶原理基础上，使用KrF准分子脉冲激光为辐照源，对aSi:H/SiO_2多层膜进行辐照，使纳米级厚度的aSi:H子层晶化.Raman散射谱和电子衍射谱的结果表明，经过激光辐照后纳米Si颗粒在原始的aSi:H子层内形成，晶粒尺寸可以根据aSi:H层的厚度精确控制.还研究了样品的光致发光（PL）特性以及激光辐照能量密度对PL性质的影响. 关键词： 脉冲激光 多层膜 限制结晶     

一种漂移室定位子性能反常现象的研究

研究了一种漂移室定位子性能的反常现象,它关系到定位子的使用寿命．着重测量了暗电流和随机噪声与时间、高压及温度的关系.     

高压下聚苯胺的结构和电性能研究

 以金刚石压腔高压装置为工具，用Ⅱ型金刚石作压砧兼红外窗口，对本征态聚苯胺进行了高压（0~8.4 GPa）就位红外光谱测试。结果表明：在4.8~5.2 GPa压力区间，代表醌环振动的吸收峰相对代表苯环振动的吸收峰变小，表明聚苯胺在此压力区间结构上发生了显著变化，且这种变化是不可逆的。聚苯胺的高压（0~14.5 GPa）电阻测量结果表明：当压力小于7.5 GPa时，电阻随压力升高而显著降低，据此认为聚苯胺为电子性导电物质；在7.5 GPa处电阻出现极小值，然后又缓慢升高，至10 GPa后基本不变。推测聚苯胺电阻极小值是由结构变化引起的。至于红外光谱与电阻测量结果反映聚苯胺结构变化的压力值不一致，可能是由于测试条件不同所致。     

Crystal structure and magnetic ordering of RNi Si compounds

The element distributions and the magnetic ordering behaviour of compounds RNi₁₀Si₂ (R = Tb, Dy, Ho, Er, Tm) have been studied by neutron powder diffraction down to temperatures of 1.6 K. The compounds crystallize in an ordered variant of the ThMn₁₂ structure type in the tetragonal space group P4/nmm. An ordered 1:1 distribution of Ni and Si on sites 4d and 4e, respectively, corresponds to a modulation vector [0, 0, 1] with respect to the space group I4/mmm of the ThMn₁₂ structure. TbNi₁₀Si₂ orders antiferromagnetically below T _N = 4.5 K with a magnetic propagation vector of [0, 0, 1/2]. The magnetic Tb moments, 8.97(2) /Tb atom at 1.6 K, are aligned along the c-axis. The Ni sites in TbNi₁₀Si₂ do not carry any ordered magnetic moments. The compounds with R = Dy, Ho, Er, and Tm are paramagnetic down to 1.6 K and 3.0 K, respectively. Received 10 July 2002 / Received in final form 12 September 2002 Published online 29 October 2002     

气体栓塞演示实验

利用自制实验装置直观地演示了水在细管中流动，若有气泡存在时产生的气体栓现象。     

高功率飞秒脉冲激光器的进展

概述了超短激光脉冲技术发展的历程。详尽的论述了啁啾脉冲放大技术的原理和一些关键技术 ,并对当今飞秒激光器研究发展的状况进行了综述。在分析其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。结果表明 ,脉冲激光放大系统以后的发展方向是 :更短脉冲 ;追求更高峰值功率 ;连续光谱调谐化 ;向小型化乃至全光纤化发展。     

Application of stochastic optimal control to the suboptimal design of thrust-mass profiles

Stochastic optimal control techniques are applied to compare the performance of identical medium-range air-to-air missiles which have different thrust-mass profiles. The measure of the performance is the probability of reaching a lock-on-point with a favorable range of guidance and flight parameters, during a fixed time interval [0,t _f ], given that, during the flight, the trajectories of the missile are subjected to a variety of constraints including dynamic pressure constraints.     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

Influence of organic modifiers on morphology and crystallization of poly(ϵ‐caprolactone)/synthetic clay intercalated nanocomposites

ε‐caprolactone was polymerized in the presence of neat montmorillonite or organomontmorillonites to obtain a variety of poly(ε‐caprolactone) (PCL)‐based systems loaded with 10 wt % of the silicates. The materials were thoroughly investigated by different X‐ray scattering techniques to determine factors affecting structure of the systems. For one of the nanocomposites it was found that varying the temperature in the range corresponding to crystallization of PCL causes reversible changes in the interlayer distance of the organoclay. Extensive experimental and literature studies on this phenomenon provided clues indicating that this effect might be a result of two‐dimensional ordering of PCL chains inside the galleries of the silicate. Small angle X‐ray scattering and wide angle X‐ray scattering investigation of filaments oriented above melting point of PCL revealed that polymer lamellae were oriented perpendicularly to particles of unmodified silicate, while in PCL/organoclay systems they were found parallel to clay tactoids. Calorimetric and microscopic studies shown that clay particles are effective nucleating agents. In the nanocomposites, PCL crystallized 20‐fold faster than in the neat polymer. The crystallization rate in nanocomposites was also significantly higher than in microcomposite. Further research provided an insight how the presence of the filler affects crystalline fraction and spherulitic structure of the polymer matrix in the investigated systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2350–2367, 2007