(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

〈111〉晶向冲击加载下单晶铜中纳米孔洞增长的早期动力学行为

利用分子动力学方法模拟计算了单晶铜中纳米孔洞在沿〈111〉晶向冲击加载下增长的早期过程.测量发现不同加载强度下等效孔洞半径随时间近似成线性变化.观测到单孔洞增长的两种位错生长机理：加载强度较低时，只在沿着冲击加载方向的孔洞顶点附近区域有位错的成核和运动；而随着加载强度超过一定阈值，在沿冲击加载和其垂直方向的孔洞顶点区域都观察到位错的成核和运动.在前一种机理作用下，孔洞只沿加载方向增长；在后一种机理作用下，孔洞同时沿加载和垂直于加载方向增长.分析孔洞表面原子的位移历史，发现沿加载及与其垂直方向的孔洞顶点沿径向的速度基本恒定，由此提出了一个孔洞生长模型，可以解释孔洞增长的线性生长规律. 关键词： 纳米孔洞 分子动力学 冲击加载 位错     

LD泵浦Nd∶LuVO4/Cr4+∶YAG被动调Q激光器

采用大功率半导体激光器端面泵浦Nd∶LuVO4晶体，利用Cr4+∶YAG晶体作为可饱和吸收元件，实现了1.06 μm激光的被动调Q运转.在泵浦功率为19.1 W时，获得最高平均输出功率为4.58 W，脉冲宽度为84 ns，单脉冲能量为36.6 μJ以及峰值功率为436.2 W的激光脉冲.     

The Calibrating Theory in the Network Parameters Measurement of Microwave and MMW Devices

The paper introduces a special system calibration technology in s-parameters measurement of microwave and millimeter wave devices. The 8-term errors module is built by analyzing the signals flowing in the measurement system. Then the calibration technology using non-standard kits is designed on the base. Finally, the experiment using the calibration technology is introduced.     

Challenging Students to View the Concept of Area in Triangles in a Broad Context: Exploiting the Features of Cabri-II

This study focuses on the constructions in terms of area and perimeter in equivalent triangles developed by students aged 12–15 years-old, using the tools provided by Cabri-Geometry II [Labore (1990). Cabri-Geometry (software), Université de Grenoble]. Twenty-five students participated in a learning experiment where they were asked to construct: (a) pairs of equivalent triangles “in as many ways as possible” and to study their area and their perimeter using any of the tools provided and (b) “any possible sequence of modifications of an original triangle into other equivalent ones”. As regards the concept of area and in contrast to a paper and pencil environment, Cabri provided students with different and potential opportunities in terms of: (a) means of construction, (b) control, (c) variety of representations and (d) linking representations, by exploiting its capability for continuous modifications. By exploiting these opportunities in the context of the given open tasks, students were helped by the tools provided to develop a broader view of the concept of area than the typical view they would construct in a typical paper and pencil environment.     

高频强泵浦场激发的等离子体参量不稳定性的特性

本文论证了当泵浦波的强度足够强时,在相当普遍的条件下,对均匀等离子体,唯一可以发生的参量不稳定性是类似于弱场的振荡二束不稳定性(OTSI)。对均匀及弱不均匀等离子体,高频强泵浦场激发的参量不稳定性都是绝对不稳定性。同样的性质在磁化等离子体中也可以得到。 关键词：     

激光等离子体2660紫外探针及干涉系统

成功地在六路高功率Nd玻璃激光装置上建立了2660紫外激光探针和适合紫外波段的Normaski干涉仪,首次将可见波长的连续激光应用于紫外干涉仪中靶成像调整和光路准直。利用该紫外光干涉仪,在铜柱状靶(φ500μm)上测量了厚等离子体中高达0.6n。的电子密度。     

Error analysis: a tool for selecting travel demand models

In developing travel demand models it is generally assumed that the base-year data used in developing the parameters, as well as the forecasted data to be used as independent variables for the design year, are of acceptable quality. The purpose of this paper is to present the application of error propagation theory in assesing the predictive quality of one type of travel demand forecasting model (multinomial logit models) and to demonstrate how error considerations can be used as a tool for identifying the optimal model. The general conclusions of this study are that: (1) it is indeed possible to quantify errors in dependent variables in logit models as a consequence of errors in independent variables; and (2) error consideration can be used as a tool for identifying the optimal model from a set of candidate models. Further research is recommended to develop better insights into the phenomenon of error propagation so that the consideration of errors can be a factor in decisions on model selection.     

A comparative study of the structure and crystallization of bulk metallic amorphous rod Pr60Ni30Al10 and melt-spun metallic amorphous ribbon Al87Ni10Pr3

Pr-based bulk metallic amorphous （BMA） rods （Pr60Ni30Al10） and Al-based amorphous ribbons （Al87Ni10Pr3） have been prepared by using copper mould casting and single roller melt-spun techniques, respectively. Thermal parameters deduced from differential scanning calorimeter （DSC） indicate that the glass-forming ability （GFA） of Pr60Ni30Al10 BMA rod is far higher than that of Al87Ni10Pr3 ribbon. A comparative study about the differences in structure between the two kinds of glass-forming alloys, superheated viscosity and crystallization are also made. Compared with the amorphous alloy Al87Ni10Pr3, the BMA alloy Pr60Ni30Al10 shows high thermal stability and large viscosity, small diffusivity at the same superheated temperatures. The results of x-Ray diffraction （XRD） and transmission electron microscope （TEM） show the pronounced difference in structure between the two amorphous alloys. Together with crystallization results, the main structure compositions of the amorphous samples are confirmed. It seems that the higher the GFA, the more topological type clusters in the Pr-Ni-Al amorphous alloys, the GFAs of the present glass-forming alloys are closely related to their structures.     

空心阴极灯激发的微波等离子体炬原子/离子荧光光谱研究--钙的原子/离子荧光光谱

用强短脉冲供电技术的空心阴极灯作激发源、微波等离子体炬作原子／离子化器，建立了原子／离子荧光光谱实验装置。详细研究了微波等离子体功率、观察高度、空心阴极灯电流等因素对原子／离子荧光信号强度的影响，测量了系统对Ca的原子／离子荧光光谱的检出限。