长光程薄层紫外-可见光谱电化学法测定多巴胺

利用一种长光程薄层光谱电化学池,建立了在抗坏血酸存在下测定多巴胺的紫外-可见光谱电化学法。测定条件为：在pH=6．0的PBS介质中,电极电位在0．6V（vs.Ag/AgCl）,测定波长为300nm多巴胺电氧化产物的吸光度,吸光度与多巴胺浓度在4×10－6～2．4×10－4mol/L范围内呈线性关系,检测限为1．0×10－6mol/L。用于多巴胺针剂的测定,结果令人满意。     

新显色剂1-羟基-2-(5-NO2-2-吡啶偶氮)-8-氨基-3,6-萘二磺酸与铜显色反应的研究

探讨了新显色剂 1-羟基-2-(5-NO2-2-吡啶偶氮)-8-氨基-3,6-萘二磺酸(简称5-NO2-PAH)与铜离子显色的适宜条件及其共存离子的影响,建立了 5-NO2-PAH测定铜的新显色反应体系.在 pH 7.0～10.0 范围内,铜与试剂形成稳定的 1∶2 配合物,其最大吸收峰位于 653 nm, 表观摩尔吸光系数εCu=4.68×104 L·mol-1·cm-1,铜的浓度在 0 μg/10 mL～14 μg/10 mL 范围内遵守比尔定律.方法已用于合金中铜的测定.     

偶氮胂Ⅲ分光光度法测定人血清中蛋白质

偶氮胂Ⅲ是测定无机离子的灵敏显色剂 ,研究发现该试剂能在pH 2 1的缓冲介质中 ,与牛血清白蛋白形成复合物 ,最大吸收波长 60 2nm ,比试剂本身红移 5 9nm ,表观摩尔吸光系数 5 6× 1 0 5L·mol- 1·cm- 1,线性范围 0～ 45 0 μg/mL。方法用于人血清样品中蛋白质的测定 ,结果可靠     

曲利本蓝-氨基糖苷类抗生素的显色反应及其分析应用

曲利本蓝 (TB)与硫酸卡那霉素 (KANA)和硫酸妥布霉素 (TOB)等氨基糖苷类抗生素在pH 2 .0～ 7.0的条件下反应生成蓝色离子缔合物。其最大显色波长位于 680nm(TOB)和 686nm(KANA) ,线性范围分别是 0～ 1 1 .0 μg mL(TOB)和0～ 1 3.0 μg mL(KANA) ,摩尔吸光系数 (ε)分别为 5 .32× 1 0 3(TOB)和 3.64× 1 0 3(KANA)L·mol-1·cm-1;最大褪色波长位于 5 88nm(TOB)和 5 90nm(KANA) ,线性范围均为 0～ 1 1 .0 μg mL ,摩尔吸光系数 (ε)分别为 1 .84× 1 0 4 (TOB)和 1 .1 1× 1 0 4(KANA)L·mol-1·cm-1。当用双波长叠加法时 ,ε值分别为 2 .37× 1 0 4 (TOB)和1 47× 1 0 4 (KANA)L·mol-1·cm-1。探讨了适宜的反应条件及主要的分析化学性质。该方法用于市售药物中氨基糖苷类抗生素的测定。     

磺硝酚偶氮若丹宁固相萃取光度法测定环境样品中的铅

在pH 4.5的HAc NaAc缓冲介质中 ,吐温 - 80存在下 ,磺硝酚偶氮若丹宁 (NSPAR)与铅反应生成 2∶1稳定络合物 ,该络合物可被WatersSep PakC1 8小柱固相萃取 ,用氮 氮二甲基甲酰胺 (DMF)洗脱后用光度法测定。在洗脱液介质中 ,λmax=5 5 5nm ,体系摩尔吸光系数ε=1 .0 2× 1 0 5L·mol- 1 ·cm- 1 。铅质量浓度在 0 .0 5～ 4.0 μg/mL内符合比尔定律 ,本方法可用于环境样品中铅的测定     

新显色剂2,4,4''''-三硝基苯基重氮氨基偶氮苯的合成及其与汞的显色反应

合成了新试剂2,4,4'-三硝基苯基重氮氨基偶氮苯(简称TNBDAA),并研究了在Triton X-100存在下其与汞的显色反应. 在pH 9.0的Na2B4O7-HCl缓冲介质中,Hg(Ⅱ)与试剂形成12的红色络合物,最大吸收波长为553 nm,表观摩尔吸光系数为1.69×105 L·mol-1·cm-1,汞质量浓度在0～0.7 μg/mL范围内服从比尔定律. 方法已用于废水中微量汞的直接测定.     

4-(2-噻唑偶氮)-苯二甘氨酸的合成及其与钯显色反应的研究

报道了水溶性 4 ( 2 噻唑偶氮 ) 苯二甘氨酸 (TAPC)新试剂的合成。该试剂对钯具有较高灵敏度和选择性。在 0 .5mol/LHNO3介质中 ,TAPC与Pd(Ⅱ )形成 2∶1蓝色配合物 ,最大吸收波长 632nm。钯浓度在 0 μg/mL～ 1 .6μg/mL范围内符合比耳定律 ,表观摩尔吸光系数ε632 =5× 1 0 4 L·mol- 1 ·cm- 1 。可允许许多离子共存 ,可直接用于含钯分子筛样中微量钯的测定     

双波长吸光光度法同时测定多巴和酪氨酸的研究

研究了双波长吸光光度法同时测定多巴和酪氨酸。在 pH 1 2 .0 0的硼砂 氢氧化钠缓冲介质中 ,多巴和酪氨酸的含量分别在 0～ 2 0 .0 μg·ml-1和 0～ 1 9.0 μg·ml-1范围内呈良好线性关系 ,方法检出限和摩尔吸光系数 :多巴为 0 .2 3 μg·ml-1和 1 .2 0× 1 0 4L·mol-1·cm-1,酪氨酸为 0 .2 7μg·ml-1和 1 .48× 1 0 4L·mol-1·cm-1,方法的灵敏度和和选择性均较好 ,应用于尿液中多巴和酪氨酸的测定。     

1-(偶氮苯基)-3-(3,5-二溴-2-吡啶)-三氮烯的合成及其与镉的显色反应

报道了 1 (偶氮苯基 ) 3 ( 3,5 二溴 2 吡啶 ) 三氮烯的合成及其与镉的显色反应。在TritonX 1 0 0存在下 ,于pH 1 0 .9的Na2 B4O7 NaOH缓冲介质中 ,镉与ABDBPDT形成摩尔比 1∶3型红色配合物。试剂及配合物的最大吸收波长分别为 430nm和 5 30nm。表观摩尔吸光系数为 1 .75× 1 0 5L·mol- 1 ·cm- 1 。镉含量在 0 μg/2 5mL～ 1 2 μg/2 5mL范围内符合比耳定律     

钒与新显色剂 1,4-双肼酞嗪显色反应的研究及应用

研究了钒与新显色剂 1,4-双肼酞嗪的显色反应.在 pH 5.8 的 HAc-NaAc 缓冲溶液中,加入溴化十六烷基三甲铵于 60℃加热 10 min,钒与 1,4-双肼酞嗪形成稳定的螯合物,λmax=422nm,ε422=1.32×104 L·mol-1·cm-1,钒的浓度在 0 μg/25 mL～20 μg/25 mL 范围内符合比耳定律,检出限为 15 ng/mL,已用于测定钢样中的微量钒.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.