光学活性偶氮苯自组装膜的制备及其蛋白吸附行为

研究了在紫外光作用下, 牛血清白蛋白(BSA)在偶氮苯自组装膜上光控可逆的吸附行为. 首先合成羧基偶氮苯衍生物, 并在金膜表面制备偶氮苯自组装膜, 采用紫外吸收光谱(UV)、原子力显微镜(AFM)观察偶氮苯衍生物的光学顺反异构现象以及偶氮苯自组装膜表面形貌的变化. 同时利用等离子体表面谐振仪(SPR)考察偶氮苯光学异构对牛血清白蛋白(BSA)在自组装膜表面上的吸附行为的影响. 结果表明, BSA在偶氮苯自组装膜表面的吸附作用主要来自于BSA分子与自组装膜之间的静电作用及亲疏水作用. 在紫外光作用下, 偶氮苯自组装膜可以实现光控可逆的牛血清白蛋白分子吸附行为.     

纳米结构TiO2/PS及TiO2空心球的自组装与表征

以TiCl₄的盐酸溶液配制的TiO₂溶胶为前驱体, 以聚苯乙烯微球为载体, 在表面活性剂存在下, 通过逐层自组装技术制备了纳米结构TiO₂/PS及TiO₂空心球. 利用XRD, SEM, TG-DTA等对复合颗粒进行了表征. 研究表明: 纳米结构TiO₂/PS的组成、结构、形貌和粒度可通过溶胶酸度、组装时水解反应温度、煅烧温度、硫酸根的加入量来控制.     

纳米结构TiO2/PS及TiO2空心球的自组装与表征

以TiCl₄的盐酸溶液配制的TiO₂溶胶为前驱体, 以聚苯乙烯微球为载体, 在表面活性剂存在下, 通过逐层自组装技术制备了纳米结构TiO₂/PS及TiO₂空心球. 利用XRD, SEM, TG-DTA等对复合颗粒进行了表征. 研究表明: 纳米结构TiO₂/PS的组成、结构、形貌和粒度可通过溶胶酸度、组装时水解反应温度、煅烧温度、硫酸根的加入量来控制.     

花状3D纳米Pd/CeO2催化剂的制备及其性能研究

以PdCl2为前驱体,十六烷基三甲基溴化铵为保护剂,用超声波膜扩散法制备了Pd纳米粒子溶胶(E,Pd负载量1.0 wt%)。采用水热法制备了3D纳米花状Pd/CeO2催化剂(F),其结构,形貌和物理化学性能经XRD,SEM和N2吸附-脱附表征。考察了晶化时间对F形貌和晶型的影响。结果表明,晶化时间72 h制备的F72具有较高的比表面积(108 m2·g-1)和较大的孔体积(0.11 cm3·g-1);晶化时间48 h制备的F48呈现花状形貌,由大量厚度(20 nm～30 nm)均匀的纳米单元自组装而成。     

超支化聚负离子/超支化聚正离子自组装膜的制备及反应

自1991年以来,静电吸附自组装已发展成为制备具有特定纳米微结构聚电介质多层超薄膜的有效技术。近年来,由于树枝状聚合物和超支化聚合物独特的物理化学性质,文献中已将它们与线性聚电解质一起用于静电吸附自组装过程,但完全基于超支化聚合物分子间的自组装过程还鲜见报道,超支化聚合物所具有的大量末端和内部（如叔胺基）官能团,不仅可以用于调节自组装行为及组装膜的表面形貌,     

不同pH条件下木质素磺酸钠的静电逐层自组装研究

以来源于造纸废液中的木质素磺酸钠(SL)为研究对象,利用静电逐层自组装技术,与聚二烯丙基二甲基氯化铵(PDAC)交替吸附,制备木质素磺酸钠的自组装多层吸附膜.研究了不同pH值条件下木质素磺酸钠在固体表面的静电吸附规律.木质素磺酸钠的自组装过程用紫外-可见光吸收光谱来监控,而自组装膜的表面形貌用原子力显微镜来观察.研究表明,SL与PDAC多层吸附膜的紫外-可见光吸收光谱强度随层数增加而线性增长,说明SL/PDAC多层吸附膜的厚度增长是以逐层自组装的方式进行的.木质素磺酸钠浸渍溶液的pH值对多层吸附膜的厚度和表面形貌产生重要的影响.在所研究的pH范围内,pH值越低,越有利于生成吸光度高的自组装膜,而得到的自组装膜的表面粗糙度越大。     

静电组装金纳米粒子制备局域表面等离子体共振传感膜

采用聚电解质自组装技术制备局域表面等离子体共振(LSPR)传感膜的方法, 在玻璃基片上依次沉积聚电解质PDDA, PSS和PVTC, 并通过静电吸附构建胶体金纳米粒子自组装膜形成LSPR传感膜. 利用扫描电镜对LSPR传感膜表面形貌以及膜中金纳米粒子的粒径进行了表征, 同时通过紫外-可见消光光谱对其灵敏度和渗透深度等重要参数进行检测. 研究结果表明, 所制备的LSPR传感膜粒子分布均匀、单分散性好、稳定性高、重现性好; 消光峰位对样品溶液折射率的检测灵敏度为71 nm/RIU, 相应的峰强检测灵敏度为0.21 AU/RIU, 对表面吸附层的渗透深度约为16 nm.     

嵌段共聚物规整纳米多孔薄膜的制备与形貌调控

通过结合嵌段共聚物自组装与非溶剂致相分离法,制备了上表面为高规整纳米直孔薄层,内部为双连续大孔支撑层的非对称薄膜结构,并考察了铸膜液浓度、溶剂挥发时间、凝固浴温度、刮膜厚度等因素对膜形貌的影响,实现对表面结构的有效调控.研究表明铸膜液浓度与挥发时间的影响有协同效应,随着铸膜液浓度的升高,规整表面孔结构所需的挥发时间减小.若铸膜液浓度不变,挥发时间的增大可使膜表面依次完成从非规整孔、规整柱状孔,再到层状孔的转变.凝固浴温度的降低有利于规整表面结构的形成.当刮膜厚度降低时,原有操作条件下的膜表面形貌形成规律将不再适用,为制备更薄的规整纳米多孔薄膜,需降低挥发时间或采用溶剂退火的方法,这一发现扩展了此类新型薄膜材料制备过程的可操作空间.     

受限空间内聚苯乙烯微粒的制备

以(N,N-二甲氨基-4-吡啶)五氰合铁(II)封端的聚氧丙烯聚氧乙烯共聚物(EPE-Fe)与苯乙烯在水中自组装形成纳米体系(EPE-Fe-St), 在纳米尺度受限空间内进行了苯乙烯自由基聚合, 制备了聚苯乙烯微球(EPE-Fe-PS). 用Fe³⁺对自组装体系的纳米球壳进行固化后形成Fe-EPE-Fe-St 体系, 聚合后也制备了聚苯乙烯微球(Fe-EPE-Fe-PS). 研究结果表明,制备了粒径为60～200 nm 的不同粒径单分散聚苯乙烯微球, 聚合温度对纳米Fe-EPE-Fe-St 体系粒径影响较小, 而对EPE-Fe-St 体系较大. 在受限空间内苯乙烯的自由基聚合可得到数均分子量超过70 万的聚苯乙烯; 自组装体系中引发剂量增多使聚苯乙烯分子量下降, 聚合温度上升也使分子量下降, 而增加自组装的EPE-Fe 用量可增加聚苯乙烯的分子量. 两种受限条件下的聚苯乙烯微球的玻璃化转变温度(T_g)在90～135 ℃之间, 纳米反应器壳层的硬化提高了聚苯乙烯微球的T_g.     

聚电解质PDDA/PSS层层自组装膜的渗透汽化性能

采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.     

Surface and biological activity of sophorolipid molecules produced by Wickerhamiella domercqiae var. sophorolipid CGMCC 1576

The ion-imprinted magnetic chitosan resins (IMCR) prepared using U(VI) as a template and glutaraldehyde as a cross-linker showed higher adsorption capacity and selectivity for the U(VI) ions compared with the non-imprinted magnetic chitosan resins (NIMCR) without a template. The results showed that the adsorption of U(VI) on the magnetic chitosan resins was affected by the initial pH value, the initial U(VI) concentration, as well as the temperature. Both kinetics and thermodynamic parameters of the adsorption process were estimated. These data indicated an exothermic spontaneous adsorption process that kinetically followed the second-order adsorption process. Equilibrium experiments were fitted in Langmuir, Freundlich, and Dubinin-Radushkevich adsorption isotherm models to show very good fits with the Langmuir isotherm equation for the monolayer adsorption process. The monolayer adsorption capacity values of 187.26 mg/g for IMCR and 160.77 mg/g for NIMCR were very close to the maximum capacity values obtained at pH 5.0, temperature 298 K, adsorbent dose 50 mg, and contact time 3 h. The selectivity coefficient of uranyl ions and other metal ions on IMCR indicated an overall preference for uranyl ions. Furthermore, the IMCR could be regenerated through the desorption of the U(VI) ions using 0.5 M HNO(3) solution and could be reused to adsorb again.     

壳聚糖对水中铝离子的吸附性能

研究了静态条件下壳聚糖对铝离子的吸附性能,探讨了壳聚糖吸附A l3+的最佳条件.结果表明,壳聚糖对水溶液中的A l3+吸附速度比较快,饱和吸附量为49.0 mg.g-1,适宜的pH为4,温度影响不大.对等温吸附平衡数据进行分析,符合Langmu ir吸附模型.对壳聚糖-铝(Ⅲ)配合物的红外光谱及电子能谱分析表明,壳聚糖分子中的氨基与A l3+发生了配位作用,吸附机理以单分子层化学吸附为主.     

Thionicotinamide SAM on Gold: Adsorption Studies and Electroactivity

STM and impedance results of the self‐assembled monolayer (SAM) formed with thionicotinamide (TNA) on gold indicate the presence of defects that increase with the immersion time of the electrode in the TNA solution affecting the SAM electroactivity toward the electron transfer reaction of the cytochrome c metalloprotein and [Fe(CN)₆]^4? and [Ru(NH₃)₆]³⁺ complexes. It was observed that this electroactivity was also affected by the pH of the electrolyte solution. SERS and STM data indicate sulfur coordination to the surface with contribution of the NH₂ group. From the dependence of the TNA surface coverage on the temperature and concentration in solution, thermodynamic parameters of adsorption were determined.     

电化法研究壳聚糖树脂与游离酸的相互作用

利用电化实验技术，跟踪观察交联壳聚糖树脂吸附低浓度游离酸的行为，讨论了酸和甲醇浓度等因素对吸附的影响，利用固-液相互作用方程，求取吸附剂一吸附质相互作用能。实验结果表明，交联壳聚糖树脂吸附低浓度游离酸的过程是遵循单分子层机制进行的，表观吸附速率常数随着吸附质浓度和外加甲醇含量的增大而减小，表观吸附速率常数与吸附剂一吸附质相互作用能（U）存在线性相关。     

A rapid method for detection of genetically modified organisms based on magnetic separation and surface-enhanced Raman scattering

In this study, a new method combining magnetic separation (MS) and surface-enhanced Raman scattering (SERS) was developed to detect genetically modified organisms (GMOs). An oligonucleotide probe which is specific for 35 S DNA target was immobilized onto gold coated magnetic nanospheres to form oligonucleotide-coated nanoparticles. A self assembled monolayer was formed on gold nanorods using 5,5'-dithiobis (2-nitrobenzoic acid) (DTNB) and the second probe of the 35 S DNA target was immobilized on the activated nanorod surfaces. Probes on the nanoparticles were hybridized with the target oligonucleotide. Optimization parameters for hybridization were investigated by high performance liquid chromatography. Optimum hybridization parameters were determined as: 4 μM probe concentration, 20 min immobilization time, 30 min hybridization time, 55 °C hybridization temperature, 750 mM buffer salt concentration and pH: 7.4. Quantification of the target concentration was performed via SERS spectra of DTNB on the nanorods. The correlation between the target concentration and the SERS signal was found to be linear within the range of 25-100 nM. The analyses were performed with only one hybridization step in 40 min. Real sample analysis was conducted using Bt-176 maize sample. The results showed that the developed MS-SERS assay is capable of detecting GMOs in a rapid and selective manner.     

β-环糊精接枝壳聚糖的合成及其吸附性能

采用乙二醛作为交联物合成了一种β-环糊精接枝壳聚糖,研究了其对水溶液中对硝基苯酚的吸附性能;考察了温度、pH值、吸附时间、酚溶液初始浓度等因素对其吸附性能的影响.结果表明,当吸附时间为20min,pH值为5~6,温度为25℃~35℃,酚溶液初始浓度为80 mg/L时,β-环糊精接枝壳聚糖对对硝基苯酚的吸附性能最佳.     

硫辛酸在金电极上自组装成膜动力学研究

自组装单层膜 (ＳＡＭ)应用广泛[1～ 3] 。但对于硫辛酸 (ＴＡ)自组装成膜动力学过程的研究尚未见报道。本研究利用石英晶体微天平 (ＱＣＭ)对ＴＡ自组装成膜过程进行在线监测 ,研究成膜动力学特征 ,并探讨浓度、温度对成膜过程的影响 ,以及在不同ｐＨ值下 ,ＳＡＭ的稳定性 ,推算了不同温度下的速率常数及成膜的活化能。1　实验部分1 1　基本原理通过监测成膜过程中石英晶体微天平 (ＱＣＭ)的振荡频率的变化 ,据Ｓａｕｅｒｂｒｅｙ方程 ,可推知在石英谐振器 (ＱＣＭ)的金电极表面 ,ＴＡ的吸附质量Γ(Γ =Δｍ Ａ ,ｇ ｃｍ2 )与ＱＣＭ的频率…     

A Self‐Assembly Phase Diagram from Amphiphilic Perylene Diimides

Supramolecular forces govern self‐assembly and further determine the final morphologies of self‐assemblies. However, how they control the morphology remains hitherto largely unknown. In this paper, we have discovered that the self‐assembled nanostructures of rigid organic semiconductor chromophores can be finely controlled by the secondary forces by fine‐tuning the surrounding environments. In particular, we used water/methanol/hydrochloric acid to tune the environment and observed five different phases that resulted from versatile molecular self‐assemblies. The representative self‐assembled nanostructures were nanotapes, nanoparticles and their 1D assemblies, rigid microplates, soft nanoplates, and hollow nanospheres and their 1D assemblies, respectively. The specific nanostructure formation is governed by the water fraction, R_w, and the concentration of hydrochloric acid, [HCl]. For instance, nanotapes formed at low [HCl] and R_w values, whereas hollow nanospheres formed when either the HCl concentration is high, or the water fraction is low, or both. The significance of this paper is that it provides a useful phase diagram by using R_w and [HCl] as two variables. Such a self‐assembly phase diagram maps out the fine control that the secondary forces have on the self‐assembled morphology, and thus allows one to guide the formation toward a desired nanostructure self‐assembled from rigid organic semiconductor chromophores by simply adjusting the two key parameters of R_w and [HCl].     

表面活性剂作用下谷胱甘肽单分子膜的离子门响应

将谷胱甘肽自组装在金电极表面,在表面活性剂存在下,以铁氰化钾及苯醌作为探针,用循环伏安法研究了修饰在金电极表面的谷胱甘肽单分子膜的电化学行为。实验发现在阳离子表面活性剂作用下,谷胱甘肽膜存在离子门行为,修饰电极表面的电子传输随阳离子表面活性剂浓度的增加而增加。阴离子表面活性剂对氧化还原探针在修饰电极上的电化学响应显示出一定的抑制作用。     

Preparation and adsorption of magnetic Co<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>-chitosan nanoparticles

In this paper, magnetic chitosan microspheres were prepared by the emulsification cross-linking technique, with glutaraldehyde as the cross-linking agent, liquid paraffin as the dispersant, and the Span-80 as emulsifier. The time of cross-linking and the ratio of Co_0.5Ni_0.5Fe₂O₄/chitosan were investigated. The morphology was studied by different instruments. The adsorption performance was investigated and the effects of initial concentration of methyl orange, the time of cross-linking, and the amount of adsorbent were discussed. It is found that the product has uniform morphology when the ratio of magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan is 1 : 2 and the time of cross-linking is 5 h; At room temperature, magnetic Co_0.5Ni_0.5Fe₂O₄–chitosan has a good adsorption toward methyl orange when the magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan dosage is 20 mg.