DNA在氨基功能化偶氮苯自组装膜表面的固定

采用简单快速的方法制备出将DNA固定在其表面的单分子层敏感膜.首先采用表面自组装技术将硅氧烷基偶氮苯衍生物H2NAzoCONHC3Si(OCH3)3(APDA-N-TMSPBA)组装在硅表面,在详细考察单分子层薄膜的化学结构、表面浸润性和分子表面形貌之后,又通过紫外吸收光谱(UV)在位考察了硅氧烷基偶氮苯衍生物的光学异构特性.在DNA在自组装薄膜固定后,X光电子能谱仪(XPS)结果显示出现了明显的磷元素信号,表明DNA分子可以成功固定在自组装膜表面.     

化学吸附自组装偶氮苯小分子单层膜及表面浸润性研究

通过化学吸附自组装的方法, 将小分子量的偶氮苯分子自组装到平滑硅基底表面, 其表面接触角为83.7°. 微结构化硅基底表面的偶氮苯单层膜上表现出超疏水的特性, 接触角达到了151.9°. 经过紫外光照射后, 该表面的接触角没有发生明显的降低.     

新型偶氮苯自组装一LB组合有序膜的构造与表征

偶氮兹及其衍生物具有独特的光致异构化和电化学反应机制,其LB单分子膜作为一种高度有序的分子组装体系,以其诱人的应用前景引起了人们的极大兴趣．然而在这方面的研究中,LB膜通常是沉积在SnO。或镀金的基片上,其结构的相对木稳定性限制了实际应用的可能性．我们利用自组装技术,在金基底表面组装了具有特定末端基团的自组装单分子膜,然后利用LB技术构造偶氮苯衍生物的单分子膜,以期得到稳定而有序的偶氮苯LB膜,且不影响其光化学和电化学活性．本文报道了这种新型偶氮苯自组装一LB组合股的结构表征及其电化学行为．亚实验部分偶…     

热诱导白蛋白与壳聚糖在溶液中的自组装

80℃热诱导牛血清白蛋白(BSA)变性,BSA疏水残基暴露在分子表面,并进一步凝胶化.采用紫外-可见光光度仪(UV-Vis)和动态激光光散射仪(DLS)考察了热处理时间、溶液p H值、壳聚糖(CS)与BSA配比等因素对CS与BSA自组装行为的影响.加热时间介于15~20 min,BSA与CS发生自组装;BSA/CS混合体系p H大于BSA等电点(p I=4.7)时,BSA与壳聚糖静电作用增强,随着p H增大,出现沉淀.BSA浓度过高,变性BSA之间聚集作用增强,导致体系出现沉淀.研究结果显示,CS阻碍了BSA自身凝胶化进程,并与BSA发生自组装.在p H=5.4的溶液中制备了BSA-CS自组装体.采用透射电镜(TEM)观察了自组装体的形态,采用DLS对其粒径及其分布进行了测试.自组装体是以BSA聚集体为核、CS分子链为壳的核壳纳米结构.制备的自组装体室温贮存40天后,其粒径和分布无明显变化.     

牛血清白蛋白在气-液界面上的吸附行为及其与含芘手性探针分子的相互作用研究

利用表面压力-时间曲线对牛血清白蛋白(BSA)在气液界面上的吸附行为和对手性探针分子D/L-[4-(1-芘基)]丁酰基-苯丙氨酸(PPs)的界面手性识别, 以及由此引起的气液界面上BSA的构象变化进行了研究. 结果表明, 界面上形成的稳定单层膜经历了漫长的构象调整过程; BSA的表面压力的变化说明其对亚相中的探针分子很强的浓度依赖性和对手性分子的区分能力. 在较高的PLP和PDP探针分子浓度下, BSA的成膜性均受到了很大抑制, 但较低的PLP和PDP探针分子浓度却转而对BSA成膜有利; 与PLP相比, PDP能更有效地与BSA在界面结合, 其复合膜的稳定性更好.     

牛血清白蛋白在医用聚氨酯弹性体表面的吸附

制备了具有较好机械性能的异佛尔酮二异氰酸酯(IPDI)型聚氨酯弹性体胶片, 并进行表面肝素化处理, 得到抗凝血医用导管材料. 将聚氨酯胶片浸泡在牛血清白蛋白(BSA)水溶液中, 利用稀溶液黏度法研究了牛血清白蛋白在聚氨酯胶片表面的动态吸附情况, 并采用界面校正黏度方程计算溶液浓度变化. 研究发现, 牛血清白蛋白分子能迅速吸附到聚氨酯胶片表面, 但达到吸附平衡需要较长时间. 牛血清白蛋白在聚氨酯表面吸附后的溶液中分子构象发生变化.     

纳米团簇-牛血清白蛋白复合物界面自组装

当表面电荷密度降低时, 纳米粒子-蛋白质复合物可在水包油(O/W)乳液界面自组装. 相对于纳米粒子, 粒度较小的纳米团簇(约2 nm)与蛋白质之间有更强的亲和力, 因此纳米团簇-蛋白质复合物可表现出不同的自组装特性. 为深入了解该特性, 对纳米团簇-牛血清白蛋白(BSA)在乳液界面自组装进行研究, 用Huckel方程计算自组装所需电荷密度范围, 用光学和电子显微镜研究纳米团簇与BSA的交联. 结果表明, 纳米团簇-BSA在乳液界面的自组装驱动力同样为表面电荷密度降低, 但纳米团簇与BSA的交联可造成无序自组装, 要实现有序自组装, 除需降低表面电荷密度外, 还需控制纳米团簇与BSA的结合率.     

核壳纳米粒子与牛血清白蛋白表面增强拉曼光谱的研究

本文用表面增强拉曼光谱(SERS)系统地研究了牛血清白蛋白(BSA)与Ag/Pt核壳纳米粒子的相互作用,特别是核壳纳米粒子与被吸附的牛血清白蛋白分子之间的界面作用,并用紫外可见光谱、圆二色光谱(CD)作为辅助手段进一步证实了BSA与核壳纳米粒子的作用状况.通过紫外光谱研究发现,核壳纳米粒子的特征吸收峰的消失表明纳米粒子完全被牛血清白蛋白包覆.用近紫外CD光谱探讨了血清白蛋白的芳基氨基酸(苯丙氨酸、酪氨酸)残基微环境的变化.为探讨牛血清白蛋白与Ag/Pt核壳纳米粒子的作用机理及纳米尺寸的生物效应奠定了理论基础.     

基于纳米金/硫堇层层自组装的新型电流型酶-癌胚抗原免疫传感器

将Nafion 膜固定在金电极(Au)表面, 通过静电吸附和共价键合作用将硫堇(Thi)和纳米金颗粒(nano-Au)层层自组装到Nafion膜修饰的金电极表面. 再通过形成的纳米金单层吸附癌胚抗体(anti-CEA), 最后用辣根过氧化物酶(HRP)代替牛血清白蛋白(BSA)封闭电极上的非特异性吸附位点, 并同时起到放大响应电流信号的作用, 从而制得高灵敏、高稳定电流型酶-癌胚抗原(CEA)免疫传感器. 通过循环伏安和交流阻抗考察了电极表面的电化学特性, 并对该免疫传感器的性能进行了详细的研究. 该传感器对CEA检测的线性范围为2.5~80.0 ng/mL, 检测限为0.90 ng/mL.     

不同表面性质聚电解质多层膜的制备及蛋白质吸附和血液相容性能

利用层层自组装方法制备了聚烯丙基铵盐酸盐(PAH)/聚苯乙烯磺酸钠(PSS)多层膜. 通过吸附或共价偶联, 在多层膜表面修饰了聚乙二醇(PEG)、牛血清白蛋白(BSA)或肝素, 通过石英晶体微天平(QCM)、椭圆偏振光谱和原子力显微镜(AFM)研究了多层膜的表面形貌及修饰方法对各种蛋白的吸附性能. 经修饰后的多层膜较基底膜的厚度均有所增大; 最外层经修饰后的多层膜吸附的BSA、纤维蛋白原及血浆蛋白的量较未修饰多层膜均有所减少. 采用SEM观察了血小板在多层膜上的黏附情况和形态变化, 计算了血小板的黏附率. 比较各多层膜的凝血酶原时间(PT), 发现修饰后的多层膜的凝血酶原时间均有所延长, 但各组间无显著性差异.     

Photosensitive Azopolymer Brushes via Atom Transfer Radical Polymerization for Protein Sensing

Novel photosensitive azopolymer brushes were synthesized via surface initiated atom transfer radical polymerization using initiator self‐assembled on Au surface. The chemical structures of azobenzene derivatives were confirmed by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). The surface morphology of azopolymers via atom transfer radical polymerization (ATRP) for different time was investigated by atomic force microscopy (AFM). Additionally, the photoisomerization of azopolymer was measured by ultraviolet‐visible spectroscopy (UV‐Vis). The results indicate that such azopolymers can undergo trans‐cis‐trans photoisomerization efficiently by photo‐irradiation with UV light. Furthermore, this photoisomerization property could also induce the reversible adsorption of bovine serum albumin (BSA) adsorption on azopolymer brush surfaces. This adsorption kinetics of the reversible process can be measured by surface plasmon resonance (SPR) spectroscopy in situ. It suggests that the protein biochips could be regenerated safely by UV irradiation rather than by being rinsed with chemical reagents.     

新型可溶性偶氮聚酰亚胺及其作为液晶光定向层应用的初步研究

以 4 ,4′ 二 (1,2 苯二酸酐 4 羧酸酯 )偶氮苯为二酐单体 ,4 十六烷氧基 4′ ,4″ 二氨基三苯甲烷为二胺单体 ,通过缩聚反应合成了可溶性偶氮聚酰亚胺 .采用红外光谱、氢核磁共振、紫外光谱和热分析等手段 ,对产物的结构、热性能及光学性能等进行了表征 .在紫外光辐照下 ,上述聚合物表现出明显的光色效应 .经线性偏振紫外光 (LPUV)辐射后的上述偶氮聚酰亚胺定向层能诱导液晶盒中液晶分子发生定向沿面排列 ,且取向均匀 .上述实验表明 ,合成的偶氮聚酰亚胺是一类潜在的液晶光定向材料 .     

侧基含偶氮苯生色团的短梗霉多糖的制备及光致变色性

利用4-(4-硝基苯偶氮)-1-萘酚的丙烯酸酯与短梗霉多糖进行接枝共聚,制备了侧基含偶氮苯生色团的短梗霉多糖聚合物,并用红外光谱、扫描电镜、X射线衍射、热重分析等手段对聚合物进行了表征.用紫外光谱研究了聚合物的光致变色性,结果表明聚合物具有良好的热稳定性和光致变色性.     

A novel ferroceneylazobenzene self-assembled monolayer on an ITO electrode: photochemical and electrochemical behaviors

A novel ferroceneylazobenzene self-assembled monolayer (SAM) has been constructed on an indium-tin oxide (ITO) electrode via the covalent attachment of 4-(4'-11-ferrocenyl-undecanoxyphenylazo)benzoic acid ( FcAzCOOH) onto a silanized ITO substrate surface and verified by reflectance infrared spectroscopy and water contact angle. Atomic force microscopy (AFM) and cyclic voltammogram (CV) indicated that the FcAzCOOH formed a uniform and reproducible SAM on the ITO electrode with a surface coverage of ca. 1.9 x 10 (-10) mol/cm (2) (87 A (2)/molecule). The reversible photoisomerization behavior of the SAM was characterized by UV-vis spectra. The azo pi-pi* transition band intensity of the SAM gradually decreased with UV (365 nm) irradiation and was almost recovered again when subsequent exposure to ambient room light (400-800 nm). The increased tilt angle of the molecules on the ITO substrate after UV irradiation further confirmed the trans-to- cis isomerization of azobenzene moieties. The CV of the trans- FcAzCOOH modified ITO electrode showed a pair of waves due to redox of the ferrocene groups in the potential range of 0 to +800 mV (vs SCE), and the peak separation of the redox wave became larger after UV irradiation and almost returned to its original value after subsequent exposure to the visible light. Rate-dependent CV curves indicated that the charge transfer rate between the ferrocene species in the SAM and the ITO electrode was slowed down after UV irradiation due to the smaller porosity of the monolayer film and the more compact barrier layer between the redox species and the ITO electrode. It is the first time to directly observe the influence of photoisomerization of the azobenzene moiety on the redox behavior of redox species in the ferroceneylazobenzene-functionalized SAM. The present results provide profound insight into the role of redox microenvironment on electron transfer kinetics and also provide a simple and facile approach to the preparation of photocontrollable electrodes.     

Photo‐stimulated “turn‐on/off” molecularly imprinted polymers based on magnetic mesoporous silicon surface for efficient detection of sulfamerazine

In this study, novel photo‐stimulated molecularly imprinted polymers based on magnetic mesoporous carrier surface were developed for selective identification and intelligent separation of sulfamerazine in complex samples. The photosensitive monomer of the molecularly imprinted polymers was azobenzene derivative 5‐[(4‐(methacryloyloxy)phenyl) diazenyl] isophthalic acid with stimulus reaction mechanisms, which has photoisomerization between trans and cis for N=N bonds. Further, the properties of the photo‐stimulated molecularly imprinted polymers were further evaluated through several sets of adsorption experiments. It illustrated that the maximum adsorption amount is 0.45 mmol/L. By ultraviolet spectrophotometry, the material reaches typical characteristic peaks of photo sensitivity, and the cycle time is 16 min. Three adsorption and desorption processes were repeated, the adsorption rate reached 34.4%. Overall, the photo‐stimulated molecularly imprinted polymers can enrich and separate determine sulfamerazine with high selectivity, which have good recovery for real samples.     

偶氮苯衍生物-β-环糊精包合物的自组装行为

研究了4-N（2’-巯基-乙基）羧基酰胺偶氮苯（Azo）与β-环糊精（β-CD）形成的包合物在金表面上的自组装行为．X射线光电子能谱（XPS）结果证实,Azo和Azo与β-CD形成的包合物均可在金表面上自组装形成单分子层膜．在包合物形成的自组装膜中,Azo与β-CD的摩尔比约为1：1．Azo自组装膜的电化学反应表现速率常数（Kobs）随组装时间的延长而明显减小,反映出自组装膜的排列随时间延长而趋于更加致密,从而抑制了偶氮苯基团的电化学诱导构型转化,降低了其电活性．而Azo与β-CD包合物自组装膜的Kobs值随组装时间变化不大,在组装76h以后,包合物自组装膜的Kobs比单纯偶氮苯自组装膜的Kobs高2个数量级以上．表明环糊精能够将偶氮苯分子隔开,从而抑制了偶氮苯在自组装膜中的聚集作用,有效地提高其电化学活性．     

Cooperative switching events in azobenzene foldamer denaturation

Insight into the mechanism of photoswitchable foldamer denaturation was gained by incorporating two azobenzene switching units (see figure; orange) into the helix backbone. Optimizing the location of the units leads to cooperative photoisomerization events, causing complete unfolding. The switching cooperativity coupled with the cooperative unfolding transition enables the design of highly photosensitive systems.     

侧链偶氮聚电解质在胶体微球表面的静电层层自组装和微胶囊制作

将侧链偶氮聚电解质应用于聚苯乙烯胶体微球表面的静电层层自组装,得到了偶氮聚电解质和聚二烯丙基二甲基氯化铵多层膜覆盖的核壳微球.实验表明,组装后偶氮苯基团发生了一定程度的解聚集,得到的胶体微球可表现出明显的光色效应.研究进一步采用含肉桂酸酯的光敏聚电解质作为交联的保护壳层,并通过光交联反应使表面层发生交联固化反应.将上述具有核壳结构的胶体球溶解去除聚苯乙烯内核后,得到了含光响应聚电解质的空心微胶囊.     

含酰胺结构的巯基自组装膜的设计与结构表征

提出了一种简便通用的合成巯基化合物的途径，以分子中的羧基CO2H为起始基团，与2-流基乙胺的氨基选择性缩合；合成了一系列具有RC（O）NHCH2CH2SH（R分别为偶氯苯衍生物，双炔衍生物及直链烷基）结构的化合物，并用接触角测量，电化学和掠角反射红外光谱（GIR-IR）等手段对这些化合物在金表面形成的自组装单分子膜进行了表征。发现4-（N－（2‘-巯基已基））酰胺偶氮苯的自组装膜表现出良好的电活性，电化学测定表面浓度为4．21×10(－10)mol·cm(-2)．当R为烷基链时，随烷基链的增长，膜的致密度与有序度增加GIR-IR证明在自组装腹中CH3（CH2）6C（O）NHCH2CH2SH的C＝O和N－H键与Au表面平行，分子轴线与Au表面近似垂直．