纳米PbO/Ti电极催化还原偏硼酸锂制备硼氢化锂

在乙二醇甲醚溶液中电解铅片,制备了铅醇盐配合物,然后将溶液直接水解、凝胶,再通过提拉法涂抹在钛丝表面,450 ℃煅烧2 h制备纳米PbO/Ti电极。 将PbO/Ti电极在0.2~1.0 mol/L LiOH+0.1~0.5 mol/L LiBO2溶液测试催化还原性能,研究了影响电解还原LiBO2制备硼氢化锂(LiBH4)的主要因素,如LiBO2和LiOH浓度等。 通过X射线粉末衍射和扫描电子显微镜对PbO/Ti电极和LiBH4进行了表征。 实验表明,纳米PbO/Ti电极表面颗粒分散较好,修饰电极催化性能稳定,放电电流较大,产率和电流效率分别达15.6%和25.3%。     

纳米TiO2-Pt修饰电极的制备及电催化活性

采用电化学合成前驱体直接水解法和电沉积法制备高活性纳米TiO2-Pt修饰电极，并使用扫描电子显微镜(SEM)对电极的表面形貌和结构进行了表征; 通过循环伏安法研究了纳米TiO2-Pt修饰电极在H2SO4溶液中的电化学行为以及对Mn2＋氧化为Mn3＋的电催化活性. 结果表明,纳米TiO2的晶粒大小约30 nm,修饰在纳米TiO2膜表面的Pt微粒呈现单分散状态,平均粒径约60 nm,纳米TiO2-Pt修饰电极的电化学性能优于纯Pt电极,对Mn2＋的电氧化具有高催化活性,非均相无隔膜电解氧化Mn2＋生成Mn3＋平均电流效率可达86％.     

纳米金/丝素复合膜修饰电极制备及对对苯二酚的电催化作用

将丝素还原HAuCl4制备的纳米金/丝素溶胶修饰在金电极表面制备了纳米金/丝素复合膜修饰电极,用于对苯二酚的催化氧化。实验表明,该修饰电极具有很好的电化学性能,在pH3.55磷酸盐缓冲溶液中以该修饰电极对对苯二酚进行检测,对苯二酚在4.0×10-6~1.0×10-4mol/L浓度范围内,其氧化峰电流与浓度呈良好的线性关系,其线性回归方程为i(μA)=0.2614 5.3539c,r=0.9995;检出限为2.0×10-7mol/L,灵敏度良好,用于实际样品分析,结果令人满意。     

纳米二氧化钛对辣根过氧化酶催化作用

将辣根过氧化物酶(HRP)固定在二氧化钛(TiO2)纳米颗粒或纳米管修饰玻碳电极(GC)上,形成纳米TiO2微粒/HRP修饰GC电极和TiO2纳米管/HRP修饰GC电极.比较了HRP在纳米TiO2微粒、TiO2纳米管电极上的直接电子转移反应.实验表明,HRP在TiO2纳米管电极表面更能有效地促进它的电活性中心发生电子交换反应.此外,还测定了HRP标记抗体的电化学性能,为抗原抗体免疫反应信号的选择提供了参考依据.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶-凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极. X射线衍射(XRD)表明纳米TiO2为锐钛矿型, 扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态, 平均粒径约25 nm. 通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性, 结果表明, 修饰电极对乙二醛的直接电氧化呈现良好的催化活性, 在0.60和1.23 V(vs SCE)出现两个氧化峰, 二者电流密度分别为16 和42 mA·cm-2, 约为纯Pt电极的2倍和1.5倍, 反应过程受浓差扩散控制.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶.凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极.X射线衍射(XRD)表明纳米TiO2为锐钛矿型,扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态,平均粒径约25nm.通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性,结果表明,修饰电极对乙二醛的直接电氧化呈现良好的催化活性,在0.60和1.23 V(vs SCE)出现两个氧化峰,二者电流密度分别为16和42 mA·cm2,约为纯Pt电极的2倍和1.5倍,反应过程受浓差扩散控制.     

二氧化铅修饰玻碳电极的镀膜/循环伏安法制备及电催化性能

采用镀膜/循环伏安法制备了PbO2修饰玻碳电极.在Pb(NO3)2溶液中,在-0.7 V 将Pb膜沉积在玻碳电极表面,然后在5 mol/L NaOH溶液中以100 mV/s速度在-1.0～1.0 V循环伏安扫描20次,PbO2膜均匀沉积在玻碳电极表面.采用交流阻抗法监控电极修饰每一过程,环境扫描电镜表征电极表面形貌.探讨了PbO2膜的沉积机理及其电化学行为,表面活性位点覆盖量为7.5×10-10 mol/cm2.PbO2修饰电极对H2O2电氧化表现出较高催化活性,起始氧化电位低至0.1 V,考察了影响催化活性的因素.计时电流法测定H2O2 (工作电位0.40 V),响应时间小于2 s; 线性范围为5.0 ×10-6 ～ 5.5×10-4 mol/L;检出限1.1×10-6 mol/L (信噪比为3).在实际水样中H2O2测定结果满意.电极在室温环境下储存30 d,其催化活性基本不变.该修饰电极制备工艺简单、重现性良好、稳定性高.     

聚中性红/纳米二氧化硅复合修饰电极直接测定抗坏血酸

用滴涂法和电化学聚合法制备了聚中性红/纳米二氧化硅修饰电极(PNR/nano-SiO2/GCE),并用循环伏安法和交流阻抗法研究了修饰电极表面的电化学行为。实验表明,该修饰电极对抗坏血酸(AA)表现出良好的电催化氧化性能,探讨了复合修饰电极协同增效作用的机理。用线性扫描伏安法研究了AA浓度与峰电流之间线性关系,在pH2.0的磷酸盐缓冲溶液中,AA氧化峰电流在1.8×10-6～5.0×10-3mol/L浓度范围内呈良好的线性关系,检出限为5.4×10-7mol/L(S/N=3)。该修饰电极制备简单,可用于药品及果蔬食品中抗坏血酸的直接测定。     

聚多巴胺-纳米金修饰玻碳电极检测芦丁

采用一锅法制备聚多巴胺-纳米金修饰玻碳电极(PDA-AuNPs/GCE),用扫描电子显微镜(SEM)对修饰电极进行表面形貌分析,并研究芦丁在该修饰电极上的电化学行为。实验表明,PDA-AuNPs/GCE对芦丁有较好的电催化氧化性能,芦丁的氧化峰电流与其浓度在1.0×10-6～1.0×10-4mol·L-1范围内成线性关系,检测下限为2.3×10-7mol·L-1(S/N=3)。该修饰电极可用于复方芦丁片中芦丁含量的检测,效果良好。     

间接电氧化法合成甘油醛

通过电化学合成前驱体和溶胶-凝胶法在Ti表面修饰一层纳米TiO2膜,在纳米Ti02膜上电沉积分散的Pt微粒制成钛基纳米TiO2-Pt(Ti/nano-TiO2-pt)修饰电极。采用循环伏安法、间接电氧化法研究了纳米Ti02-Pt修饰电极的电催化活性以及Mn^3 ／Mn^2 媒质氧化甘油为甘油醛的过程。结果表明,纳米Ti02-Pt修饰电极对Mn^2 的电氧化具有高催化活性,电流效率可达90％以上,非均相电解得到的Mn^3 可一步氧化甘油为甘油醛,收率为91％。     

羟基新戊醛在PbO2-SPE组合电极上的电氧化研究

采用热压-电镀法制得PbO₂-固体高聚物电解质(SPE)组合电极. 通过伏安曲线和槽压与过电位曲线的测量, 研究羟基新戊醛在该组合电极上电氧化行为. 通过PbO₂-SPE组合电极在阳极液中有、 无液相支持电解质及不同阴极液情况下的循环伏安曲线和线性伏安曲线比较, 证明该组合电极对羟基新戊醛氧化有较好的电催化作用.     

2-甲基吡啶在PbO2-SPE组合电极上的电氧化研究

分别采用热压法和热压-电镀法制备PbO2-SPE组合电极, 通过循环伏安和稳态极化曲线测量, 研究了这两种电极对2-甲基吡啶电氧化反应的电催化活性, 同时考察了工作电极电解液中有、无液相支持电解质电位与电流密度的关系及不同对电极电解液情况下, 电流密度与过电位和过电位与槽压的关系. 通过一般PbO2电极与热压-电镀法PbO2-SPE组合电极在电流密度与过电位和电流密度与槽压变化的比较, 发现热压-电镀法制备的PbO2-SPE组合电极在相同过电位下具有更高的电流密度, 在相同电流密度下具有较低的槽压.     

纳米银-磷酸锆复合膜修饰电极的制备和电化学

合成了新型纳米银-磷酸锆复合材料并用其修饰玻碳电极,用循环伏安法对修饰电极进行电化学研究.结果表明,此复合膜保持了银的纳米尺寸的微粒性质和磷酸锆对碱性染料的电位调制能力.复合膜中的纳米银提高了磷酸锆对中性红的吸附能力,增强了中性红的氧化还原反应活性.复合膜修饰电极表现出更灵敏的电化学响应.复合膜比单纯的磷酸锆膜表现出更好的机械强度,用其制备的修饰电极表现出更好的稳定性.     

Electrogenerated chemiluminesence method for the determination of riboflavin at an ionic liquid modified gold electrode

A highly sensitive electrogenerated chemiluminescence (ECL) method for the determination of riboflavin was developed based on the enhancement of ECL intensity of lucigenin at room temperature ionic liquids (RTILs) modified gold electrode. RTILs modified gold electrode exhibited excellent electrochemical and ECL property to lucigenin system and the ECL intensity of lucigenin was greatly enhanced by riboflavin. The characterization of the RTILs modified electrode and the attractive performance of the sensitive ECL method for the determination of riboflavin were investigated. Under the optimized conditions, the ECL intensity was directly proportional to the concentration of riboflavin in the range from 5.0×10(-10) g/mL to 1.0×10(-8)g/mL with the detection limit of 1×10(-10) g/mL. The method has been applied to the determination of riboflavin in the pharmaceutical preparations with satisfactory recovery from 96% to 101%. This work demonstrates that the incorporation of ECL method with RTILs modified electrode is a promising strategy for the determination of organic compounds with high sensitivity and good reproducibility.     

蒿甲醚在单壁碳纳米管修饰电极上的电催化还原

研制了单壁碳纳米管(SWCNTs)修饰玻碳电极。用交流阻抗谱法(EIS)和扫描电镜(SEM)研究了电极膜性能,应用循环伏安法(CV)、计时库仑法(CC)、计时电流法(CA)研究了蒿甲醚在修饰电极上的电化学行为。结果表明,SWCNTs修饰电极对蒿甲醚的还原有良好的电催化活性,其还原反应为双电子过程,电极反应的扩散系数及速率常数分别为6·67×10-4cm2·s-1及8·54×10-2mol·L-1·s-1。在优化实验条件下,还原峰的峰电位位于-0·85V,其峰电流与蒿甲醚浓度在6·71×10-7~2·45×10-4mol·L-1范围内呈良好线性,检出限达4·02×10-7mol·L-1,相对标准偏差(n=10)为4·2%,可用于蒿甲醚样品的含量测定。     

3-甲基吡啶电氧化合成烟酸的研究

在有阳离子交换膜的电解槽内,通过稳态极化曲线测量,考察了3-甲基吡啶在Pt电极和PbO₂/Ti电极上的电极反应,发现PbO₂/Ti电极对生成烟酸有电催化作用.通过高效液相色谱分析,进一步考察了各种因素对电流效率的影响.     

Electrochemical Studies of Oxidation of Lomefloxacin and Interaction with Calf Thymus DNA at Nano‐SnO2/DHP Modified Electrode

A nanoparticle thin film modified electrode has been constructed using a glassy carbon electrode (GCE) coated with a nano‐tin oxide/dihexadecylphosphate (nano‐SnO₂/DHP). In pH 6.0 phosphate buffer solutions (PBS), lomefloxacin (LMF) appeared as an anodic peak with peak potential of 1.35 V at nano‐SnO₂/DHP modified electrode. In comparison with a bare GCE or a nano‐SnO₂ modified electrode, the nano‐SnO₂/DHP modified electrode exhibited an enhanced effectiveness for the oxidation of LMF. Cyclic voltammetry (CVs) coupled with fluorescence and UV/vis absorbance spectra techniques were used to study the interaction of LMF with Calf thymus DNA (ctDNA) in phosphate buffer solutions (PBS). The interaction of LMF and ctDNA could result in a considerable decrease in the peak currents and positive shift in the peak potential, as well as changes of fluorescence, UV/vis adsorption spectra and gel electrophoresis. All the acquired data showed that the new adduct between LMF and ctDNA was formed. Electrochemistry coupled with spectroscopy techniques could provide a relatively easy way to obtain useful information about the molecular mechanism of LMF‐ctDNA interactions.     

纳米TiO2膜用于光催化氧化测定化学需氧量的研究

A photocatalytic oxidation method for determination of chemical oxygen demand （COD） using nano-TiO2 film, based on the use of a nano-TiO2-Ce（SO4）2 system and electrochemical detection, was proposed. The technique was originated from the direct determination of the Ce（Ⅲ） concentration change resulting from photocatalytic oxidation of organic compounds. Ce（Ⅲ）, which was produced by photocatalytic reduction of Ce（SO4）2, could be measured at a multi-walled carbon nanotubes （MWNT） chemically modified electrode （CME）. The COD values by this method were calculated from the differential pulse voltammetry （DPV） current of Ce（Ⅲ） at the CME. Under the optimal operation conditions, the detection limit of 0.5 mg·L^-1 COD with the linear range of 1-600 mg·L^-1 was achieved. This method was also applied to determination of various COD of ground water and wastewater samples. The resuits were in good agreement with those from the conventional COD methods, i.e., permanganate and dichromate ones.     

Electrocatalytic Sensor for the Determination of Chemical Oxygen Demand Using a Lead Dioxide Modified Electrode

An amperometric method that makes use of a nano‐PbO₂ modified electrode as an electrocatalytic sensor for the determination of chemical oxygen demand (COD) is described. The sensor signal was observed as a result of the detection of the oxidation current due to electrocatalytic oxidation of organic compounds in the sample solution. This sensor responded linearly to the COD_Cr of standard samples in the range of 5–3 000 ppm and the detection limit was 2.5 ppm. When using the sensor to determine real samples, it displays short analysis time, simplicity and no sample pretreatment. The sensor was stable for over 20 days in real wastewater samples and has successfully been applied to the determination of COD in real wastewater samples.     

Fabrication of Cu−CeO2 Coated Multiwall Carbon Nanotube Composite Electrode for Simultaneous Determination of Guanine and Adenine

A copper nano particles and cerium (IV) oxide modified carbon nanotube based composite on glassy carbon electrode (Cu−CeO₂/MWCNT/GCE) was fabricated for simultaneous determination of guanine and adenine. The surface morphology, chemistry and conductance of the prepared electrodes were characterized by scanning electron microscopy (SEM), energy dispersion X‐ray (EDX), X‐Ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The Cu−CeO₂/MWCNT/GCE improved electrochemical behaviour of guanine and adenine compared to other electrodes. The modified electrode was also used for individual and simultaneous determination of guanine and adenine. Under optimized conditions, the calibration curves were obtained linearly in the range of 0.20 to 6.00 μM for the guanine and 0.10 to 8.0 μM for the adenine by differential pulse voltammetry. The limits of detection of guanine and adenine were calculated as 0.128 and 0.062 μM, respectively. Interferences studies were also performed in the presence of inorganic and organic compounds. Moreover, the determination of guanine and adenine contents were carried out in a calf thymus DNA sample by the developed method with satisfactory results.