辉光放电光谱法定量分析金属材料表面纳米级薄膜的研究

介绍了利用辉光放电光谱法分析金属材料表面的纳米级薄膜。通过优化辉光光源的放电参数，计算标准样品的溅射率。溅射率经校正后，建立各元素的标准工作曲线，从而形成了纳米级薄膜的定量表面分析方法。试验证明，此方法对膜厚的测定具有很好的准确度和精密度，可应用于多种金属材料表面纳米级薄膜的研究。     

CoFe2-xRExO4(RE=Tb,Dy)纳米晶薄膜的化学合成及磁性

以溶胶-凝胶法制备了稀土铽或镝掺杂的钴尖晶石铁氧体纳米晶薄膜.考察了Tb或Dy的掺杂量及晶化条件对晶相的影响.结果表明,稀土离子的掺杂量x超过0.3时,样品很难形成尖晶石单相.原子力显微镜对纳米晶薄膜表面形貌的观测显示,溶胶-凝胶法制备的薄膜粒度可控制在20～50nm,且具有较高的表面平整度.对于厚度为200nm的薄膜,均方根粗糙度仅为4～5nm.磁特性研究发现,掺杂Tb或Dy的样品矫顽力明显提高.     

掺杂纳米晶铁酸盐表面电子重组能与光伏特性的关系

通过表面光伏（SPV）和电场诱导表面光伏(EFISPV)技术，以光量子激发空间电荷区内电荷的转移跃迁作为电子探针，测定纳米晶铁酸镧样品中掺杂锶前后表面光电阈值的变化.结果发现，在相同的敏感气体环境下，与纳米晶铁酸镧样品相比，掺杂的纳米晶铁酸锶镧的光电阈值显著降低，表现出更加明显的表面效应.提出利用掺杂前后样品阈值能量的改变，定量计算掺杂样品表面电子重组能的方法.分析并讨论产生上述表面电子重组能的主要原因.     

多孔硅表面的激光解吸离子化质谱

多孔硅表面的解吸离子化质谱是一种新的生物质谱分析方法。克服了MALDI-TOF-MS中的基体干扰,适合进行了小分子分析。提出了新的样品制备方法,可以扩大测定范围,消除吸附杂质的干扰。发现该方法与多孔硅的光致光特性及表面疏水性无关。具有纳米结构的多孔硅作为该方法中能量的接收器。利用DIOS方法分析了氨基酸、肽、蛋白、糖等样品。此方法用于环糊精合成产物的分析,也得到了较好的结果。     

Ag/SiO2复合薄膜的紫外光还原制备及其光学性能

采用溶胶凝胶法(sol-gel)制备不同Ag掺杂量的Ag/SiO2复合薄膜,通过紫外辐射技术对薄膜进行了还原处理,采用XRD、SEM、IR、UV-Vis、Raman和荧光光谱(PL)等技术对薄膜样品结构进行了表征和光学性能测试.XRD结果表明,复合薄膜样品中的Ag纳米粒子呈面心立方相,利用谢乐公式计算出金属银的平均晶粒尺寸约为10.2 nm;SEM结果显示,所得Ag/SiO2复合薄膜均匀性良好,薄膜中绝大部分纳米颗粒尺寸较小,薄膜约厚1μm;UV-Vis结果表明,随着,nAg/nSi的增加,Ag纳米粒子在420 nm附近的表面等离子共振吸收峰逐渐增强,并伴有一定的红移;PL谱表明,由于Ag纳米粒子的表面等离子共振,薄膜样品在442 nm处发出强光,并且随着Ag浓度增大,发光强度略有降低,出现蓝移;从Raman光谱可以看出由于Ag纳米颗粒表面局域电磁场增强造成的表面增强的拉曼散射(SERS).     

钇离子掺杂对二氧化钛纳米薄膜光诱导超亲水性能的影响及其机理

用溶胶-凝胶法和浸渍-提拉法工艺,在玻璃表面上制备了均匀、透明的钇离子(Y³⁺)掺杂二氧化钛纳米薄膜。用XRD分析了样品的晶相及其与热处理温度的关系,用X射线光电子能谱(XPS)分析了薄膜表面氧的状态,用可见光吸收光谱分析了涂膜层数对透光率的影响,用接触角仪测定了其亲水性。研究了Y³⁺掺杂本身和具体的掺杂量、光照强度和时间对薄膜亲水性的影响。研究结果表明,掺杂Y³⁺的二氧化钛纳米薄膜,在物质的量分数x(Y³⁺/Ti⁴⁺)=1.5%时,经紫外光照30min或自然光照1h后,与水的接触角小于5°,表现出超亲水性;与纯二氧化钛纳米薄膜相比,其超亲水性对光诱导更为敏感;在有实用意义的超亲水性的稳定方面也有明显的改善;这应部分地与固体化学所描述的Y³⁺掺杂所造成固定、额外并且是高浓度的氧空位有关。     

《理化检验-化学分册》第41卷（2005年）总目次

试验与研究期页HPLC法快速测定食品中糖精钠、苯甲酸、山梨酸和咖啡因…………………………………………………………………1 2白菜DNA甲基化水平的反相离子对高效液相色谱法研究…………………………………………………………………1 5微柱高效液相色谱和质谱法测定烟草样品中多酚…………1 7二苯甲酰甲烷-磷酸三丁酯增塑泡塑富集光度法测定水中痕量铀………………………………………………………1 11气浮溶剂浮选光度法测定食品中痕量SO32-的研究………2 77辉光放电光谱法分析掺杂纳米硅薄膜的研究………………2 80热镀锌合金中微量铈…     

阳极氧化TiN薄膜制备N掺杂纳米TiO2薄膜及其可见光活性

室温下通过电泳沉积(EPD)的方法在Ti片表面制备TiN薄膜, 然后对TiN薄膜进行阳极氧化得到N掺杂多孔纳米结构的TiO2薄膜. 利用X射线衍射(XRD), X射线光电子能谱(XPS), 扫描电子显微镜(SEM)及光电化学方法对得到的薄膜进行表征. XRD测试结果表明, 经过阳极氧化并在350 ℃空气气氛中退火1 h的薄膜中存在锐钛矿晶型的TiO2. XPS的结果表明, 样品中的N元素取代部分O, 且N的摩尔分数为0.95%. SEM显示, 经阳极氧化后薄膜表面出现多孔纳米结构. 光电化学测试结果显示, 阳极氧化提高了N掺杂TiO2薄膜在可见光下的光电响应. 经阳极氧化并热处理的薄膜在0 V电位及可见光照射下光电流密度为2.325 μA·cm-2, 而单纯热处理的薄膜在相同条件下光电流密度仅为0.475 μA·cm-2. 阳极氧化得到纳米多孔结构提高了N掺杂纳米TiO2薄膜的表面积, 从而对可见光的响应增大.     

阳极氧化TiN薄膜制备N掺杂纳米TiO2薄膜及其可见光活性

室温下通过电泳沉积(EPD)的方法在Ti片表面制备TiN薄膜,然后对TiN薄膜进行阳极氧化得到N掺杂多不孔纳米结构的TiOz薄膜.利用x射线衍射(XRD),X射线光电子能谱(XPS),扫描电子显微镜(SEM)及光电化学方法对得到的薄膜进行表征.XRD测试结果表明,经过阳极氧化并在350℃空气气氛中退火1 h的薄膜中存在锐钛矿晶犁的TiO2.xPs的结果表明,样品中的N元素取代部分O,且N的摩尔分数为O.95%.SEM显示,经阳极氧化后薄膜表面出现多孔纳米结构.光电化学测试结果显示,阳极氧化提高了N掺杂TiO2薄膜在可见光下的光电响应.经阳极氧化并热处理的薄膜在0 V电位及可见光照射下光电流密度为2.325μ.cm2,而单纯热处理的薄膜在相同条件下光电流密度仅为0.475μA·cm-2.阳极氧化得到纳米多孔结构提高了 N 掺杂纳米 Ti02 薄膜的表面积,从而对可见光的响应增大.     

超低介电常数介孔氧化硅薄膜的制备及其表征

研究了以正硅酸乙酯(TEOS)和甲基三乙氧基硅烷(MeSi(OEt)₃)为混合硅源，十六烷基三甲基溴化铵(CTAB)为模板剂，采取旋涂技术，在硅晶片表面制备出二氧化硅透明薄膜，再经过正硅酸乙酯(TEOS)蒸汽孔壁强化后采用线性升温焙烧法脱除薄膜孔道内的模板剂，制备出具有超低介电性能的氧化硅薄膜。使用FTIR、XRD和SEM对样品进行了结构表征，并采用阻抗分析仪测量了薄膜的介电常数(k)，纳米硬度计测量薄膜的弹性模量。介孔氧化硅薄膜在常温常湿条件下存放15 d后，介电常数     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.