纳米级二氧化锆的合成及其在六价铬污染处理中的应用

用溶胶－凝胶法合成了纳米级ZrO2,并采用透射电镜进行了表征。研究了纳米ZrO2对Cr(Ⅵ）的吸附。在pH4.0，吸附比为1：2900时，平均吸附率为85．48％，最大吸附量为301．4μg Cr（Ⅵ）/g。采用2mol/L NaOH可完全洗脱纳米ZrO2l所吸附的Cr(Ⅵ）。应用于环境水样中Cr(Ⅵ）的处理，水中残留Cr(Ⅵ)的浓度远小于Cr(Ⅵ)的排放标准。考察了回收纳米ZrO2对Cr(Ⅵ)的吸附效率，结果表明纳米级ZrO2可循环使用。     

交联羧甲基淀粉预富集-悬浮体进样-石墨炉原子吸收法测定水样中铬(Ⅲ)和铬(Ⅵ)

以交联羧甲基淀粉(CCMS)为吸附剂,悬浮体进样-石墨炉原子吸收法(GFAAS)测定环境水样中Cr(Ⅲ)和Cr(Ⅵ)形态。研究了溶液pH值、吸附时间、溶液体积、共存离子等对CCMS吸附Cr(Ⅲ)和Cr(Ⅵ)的影响。结果表明:在pH=6.0时,吸附15 min,CCMS可以选择性地吸附Cr(Ⅲ),对Cr(Ⅵ)不吸附,从而实现Cr(Ⅲ)和Cr(Ⅵ)的分离。将吸附Cr?的CCMS加0.1%的琼脂制成悬浮体直接进石墨炉检测,用1 mL 1%盐酸羟胺将Cr(Ⅲ)还原成Cr(Ⅵ),测总铬。方法对Cr(Ⅲ)的检出限为0.044μg/L,相对标准偏差(RSD)为10.4%(初始浓度CCr(Ⅲ)=1.0μg/L,n=11),富集倍数为50倍。将本方法应用于环境标准样品的测定,测得结果与标准值相符。     

嵌段分子筛聚合材料P123-SH萃取分离-石墨炉原子吸收光谱法分析痕量铬的形态

研究了嵌段分子筛聚合材料P123-SH萃取分离-石墨炉原子吸收光谱法对尿中痕量铬的形态分析方法,探讨了嵌段分子筛聚合材料P123-SH吸附铬的原理和最佳条件。在pH 7.0、常温下,Cr3+和Cr(Ⅵ)被很好的分离,且Cr3+可被该材料定量吸附,其吸附容量为6.15 mg/g。吸附的Cr3+可用2 mol/L的HCl洗脱,用石墨炉原子吸收法测定洗脱下来的Cr3+,往溶液中加入0.1%抗坏血酸将Cr(Ⅵ)还原为Cr3+测总铬,Cr(Ⅵ)含量为总铬减去Cr3+,方法测定Cr3+的检出限为0.011μg/L(3σ,n=11),线性范围为0.1～10μg/L,加标回收率在94%～106%之间,对0.50μg/L的Cr3+溶液平行测定7次,RSD为3.6%。方法可应用于生物样品和环境样品中痕量铬的形态分析。     

反相离子对色谱-电感耦合等离子体质谱联用技术测定水中痕量Cr(Ⅲ)与Cr(Ⅵ)

建立了反相离子对色谱(RPIPC)与电感耦合等离子体质谱(ICP-MS)联用技术快速分离测定水中痕量Cr(Ⅲ)和Cr(Ⅵ)的方法.通过考察流动相的pH值、离子对试剂及甲醇的浓度和EDTA的添加等对不同形态铬的保留时间及分离度的影响,确定当流动相组成为2.0 mmol/L TBA,5%(V/V)甲醇,pH=5.5时,Cr(Ⅲ)与Cr(Ⅵ)可达最佳分离.ICP-MS测定时选用碰撞池技术以消除40Ar12C+与35Cl16OH+对52Cr+的谱学干扰;进样100 μL时,Cr(Ⅲ)与Cr(Ⅵ)的检出限分别为0.15 μg/L和0.16 μg/L.加标回收率在93.6%～106.2%之间; RSD<4%(n=3).以本方法分析了某市自来水、雨水及某品牌纯净水中Cr(Ⅲ)与Cr(Ⅵ)的含量,结果令人满意.     

活性氧化铝微柱分离富集-电感耦合等离子体原子发射光谱法在线测定水中铬（Ⅲ）和铬（Ⅵ）

研究了活性氧化铝对Cr(Ⅲ)和Cr(Ⅵ)分离富集的性能，建立了流动注射(FI)-在线微柱分离富集-电感耦合等离子体原子发射光谱(ICP-AES)法测定水中微量Cr(Ⅲ)和Cr(Ⅵ)的分析方法。优化了流动注射测定的条件，进样频率为60/h；检出限(3σ)：Cr(Ⅲ)为0．8μg/L，Cr(Ⅵ)为0．6μg/L；线性范围为5-600μg/L;相对标准偏差小于2．4％；回收率为94．0％-102％。     

纳米Al2O3微柱分离/富集-石墨炉原子吸收法测定环境试样中的痕量铅和镉

本文将纳米氧化铝微柱分离系统与石墨炉原子吸收光谱法联用,用于测定环境水样中的痕量铅和镉。较系统地考察了纳米Al2O3材料对镉和铅离子的吸附性能及影响因素;在优化的实验条件下本法对Pb和Cd的检出限(3σ)分别为0.189 ng/mL和0.0039 ng/mL;RSD%分别为3.9%和2.9%。     

微乳相萃取分离富集-原子吸收光谱法分析铬形态

建立了一种微乳相萃取分离-石英双缝管原子捕集火焰原子吸收光谱法(STAT-FAAS)分析环境水样中铬形态的新方法。该方法中,Cr(Ⅲ)与8-羟基喹啉反应形成的疏水性配合物,经萃取进入微乳相,Cr(Ⅵ)留在水溶液中,从而实现Cr(Ⅲ)与Cr(Ⅵ)的相互分离。Cr(Ⅵ)含量的测定通过过氧化氢溶液将Cr(Ⅵ)还原为Cr(Ⅲ),按同样方法分析。实验对微乳相萃取的主要影响因素进行了优化。结果表明,经优化后实验条件为:平衡温度80℃,平衡时间10min,溶液酸度pH=9.0,NH3-NH4Cl缓冲溶液用量2.0mL,8-HQ用量0.05mmol;TritonX-100微乳液组成:m(TritonX-100):m(正戊醇):m(正己烷):m(水)=3.0:15:1.5:4.0。在此条件下,萃取的富集倍数达到25倍(50mL起初样品溶液/2mL最终测定液),线性范围为2.5～500μg/L,检出限为0.62μg/L,相对标准偏差(RSD)为3.8%(n=10,c=10μg/L)。本方法已成功地应用于电镀废水中铬形态分析。     

原子吸收光谱法研究双水相体系对铬的选择性萃取分离效率

研究了乙醇-硫酸铵双水相体系对Cr(Ⅵ)的选择性萃取分离效率及其原子吸收光谱法(AAS)分析. 配制乙醇-硫酸铵双水相体系, 并考察不同种类盐, 盐用量, 酸度和时间对体系萃取分离效率的影响, 用AAS法测定体系对以重铬酸根形式存在的Cr(Ⅵ)的选择性萃取分离效率, 通过乙醇和水相的AAS法测定选择了最佳萃取分离条件, 在pH为4的酸性介质中把水相中的Cr(Ⅵ)萃取到乙醇相而Cr(Ⅲ)留在水相中, 使两种形态的铬彼此分离, 通过对醇相Cr(Ⅵ)和水相Cr(Ⅲ)的 AAS测定, 得到最佳测定条件及体系对Cr(Ⅵ)的萃取率为: 双水相体系的体积为10.0 mL, V(EtOH)∶V(H2O)=2∶3, (NH4)2SO4的质量为1.7 g, pH 4, Cr(Ⅵ)萃取率为90% 以上, Cr(Ⅲ)回收率为98%～108%. 本法可用于铬的形态分析.     

双硫腙修饰纳米TiO2分离富集石墨炉原子吸收光谱法测定水样中痕量金属离子

建立了双硫腙修饰纳米TiO2分离富集-石墨炉原子吸收光谱法测定水样中痕量镉、铬和铅的新方法,优化了纳米TiO2-双硫腙对试样中这3种痕量物质的吸附和解吸条件。结果表明,在pH 5.0时,镉、铬和铅可被定量吸附,静态饱和吸附容量分别为13.3、5.5、21.8 mg/g。吸附的各种金属离子可用5 mL 0.1mol/L的硝酸完全洗脱。该方法对Cd2+、Cr3+和Pb2+的检出限(3σ,n=11)分别为0.18、0.51、1.92 ng/L,相对标准偏差分别为2.8%、2.3%和1.0%,加标回收率为96%～101%。该方法已成功应用于环境水样中镉、铬和铅的测定。     

PTFE-g-GMA-PEI纤维填充微柱/ICP-OES在线预富集测定痕量Cr(Ⅵ)和Cr(Ⅲ)研究

采用自制固相萃取材料聚乙烯亚胺胺化的接枝甲基丙烯酸缩水甘油酯的聚四氟乙烯(PTFE-g-GMA-PEI)纤维填充微柱预富集和流动注射(FI)与电感耦合等离子发射光谱仪(ICP-OES)联用测定样品中痕量Cr(Ⅵ)和Cr(Ⅲ)。对Cr(Ⅵ)和Cr(Ⅲ)的富集与洗脱条件进行优化,并给出Cr(Ⅲ)离子的分析特性。结果表明,该法测定的Cr(Ⅲ)离子富集倍数为30,样品通量为72h-1,检出限为2.2μg/L,RSD为1.2%(50μg/L,n=9),其线性范围为2～500μg/L。该法成功用于环境水样中铬的形态分析,其加标回收率为90～104%。     

Speciation of chromium by selective separation and preconcentration of Cr(III) on an immobilized nanometer titanium dioxide microcolumn

Nanometer titanium dioxide immobilized on silica gel (immobilized nanometer-scale TiO2 particles) was prepared by a sol-gel method and characterized by X-ray diffraction and scanning electron microscopy. The adsorptive behavior of Cr(III) and Cr(VI) on immobilized nanometer TiO2 was assessed. Cr(III) was selectively sorbed on immobilized nanometer TiO2 in the pH range of 7-9, while Cr(VI) was found to remain in solution. A sensitive and selective method has been developed for the speciation of chromium in water samples using an immobilized nanometer TiO2 microcolumn and inductively coupled plasma atomic emission spectrometry. Under optimized conditions (pH 7.0, flow rate 2.0 mL/min), Cr(III) was retained on the column, then eluted with 0.5 mol/L HNO3 and determined by ICP-AES. Total chromium was determined after the reduction of Cr(VI) to Cr(III) by ascorbic acid. The adsorption capacity of immobilized nanometer TiO2 for Cr(III) was found to be 7.04 mg/g. The detection limit for Cr(III) was 0.22 ng/mL and the RSD was 3.5% (n = 11, c = 100 ng/ mL) with an enrichment factor of 50. The proposed method has been applied to the speciation of chromium in water samples with satisfactory results.     

On-line speciation and determination of Cr(III) and Cr(VI) in drinking and waste water samples by reversed-phase high performance liquid chromatography coupled with atomic absorption spectrometry

A simple, rapid, and selective on-line method for the speciation and determination of Cr(III) and Cr(VI) in aqueous solutions by ion-pairing HPLC coupled with flame atomic absorption spectrometry (FAAS) is described. The composition of the mobile phase has been optimized for better separation. The effects of column temperature, volume of injection loop, fuel flow rate of FAAS, and nebulizer suction rate of FAAS have also been investigated. Separation is accomplished in almost 2.5 min on a 25 cm length C18 column at 40 degrees C. The selectivity of the method has been established by investigating the effect of interfering elements on chromium determination. The detection limit (3sigma) achieved by the method was calculated as 3.7 ng/mL for Cr(III) and 2.0 ng/mL for Cr(VI). The proposed method has been validated by analyzing certified reference material (BCR 544) and successfully applied to the analysis of drinking water and wastewater samples with a relative error below 6%.     

DCB-偶氮胂高灵敏光度法测定痕量铬(Ⅵ)

本文研究了 DCB偶氮胂与 Cr2 O2 - 7的褪色反应。结果表明 ,在硝酸介质中褪色反应具有高的灵敏度 ,拟定了反应的最佳条件 ,建立了一种新的光度法测定痕量铬( )方法。本法检出限为 4.2 2× 1 0 - 11g/m L ,线性范围为 0～ 0 .8μg/1 0 m L ,用于测定人发中的痕量铬 ( ) ,结果令人满意     

Speciation Analysis of Cr(III) and Cr(VI) after Solid Phase Extraction Using Modified Magnetite Nanoparticles

A new solid phase extraction (SPE) method has been developed for the speciation of Cr(III) and Cr(VI). This method is based on the adsorption of Cr(VI) on modified alumina‐coated magnetite nanoparticles (ACMNPs). Total chromium in different samples was determined as Cr(VI) after oxidation of Cr(III) to Cr(VI) using H₂O₂. The chromium concentration has been determined by flame atomic absorption spectrometric (FAAS) technique and amount of Cr(III) was calculated by substracting the concentration of Cr(VI) from total chromium concentration. The effect of parameters such as pH, amount of adsorbent, contact time, sample volume, eluent type, H₂O₂ concentration and cetyltrimethylammonium bromide (CTAB) concentration as modifier on the quantitative recovery of Cr(VI) were investigated. Under the optimal experimental conditions, the preconcentration factor, detection limit, linear range and relative standard deviation (RSD) of Cr(VI) were 140 (for 350 mL of sample solution), 0.083 ng mL^?1, 0.1‐10.0 ng mL^?1 and 4.6% (for 5.0 ng mL^?1, n = 7), respectively. This method avoided the time‐consuming column‐passing process of loading large volume samples in traditional SPE through the rapid isolation of CTAB@ACMNPs with an adscititious magnet. The proposed method was successfully applied to the determination and speciation of chromium in different water and wastewater samples and suitable recoveries were obtained.     

微波灰化-液相色谱-电感耦合等离子体质谱联用测定干食用菌中的三价铬和六价铬

建立了干食用菌中三价铬(Cr(Ⅲ))和六价铬(Cr(Ⅵ))的液相色谱-电感耦合等离子体质谱(LC-ICP-MS)检测方法。采用微波灰化技术对食用菌样品进行灰化处理,灰化样品用乙二胺四乙酸(EDTA)二钠盐稳定其中的Cr(Ⅲ),并使其保留在阴离子交换柱(250 mm×4.6 mm,10 μm)上;用含有60 mmol/L硝酸(pH 9.3)的流动相分离其中的Cr(Ⅲ)和Cr(Ⅵ),电感耦合等离子体质谱仪测定。标准溶液中Cr(Ⅲ)和Cr(Ⅵ)的质量浓度在0.5~50 μg/L范围内呈良好的线性关系,线性回归系数均达到0.9999。食用菌样品中Cr(Ⅲ)和Cr(Ⅵ)不同加入量的平均回收率为78.0%~90.7%,相对标准偏差小于4%(n=6);定量限均为0.5 μg/L。该方法稳定、可靠、灵敏,可满足干食用菌中Cr(Ⅲ)和Cr(Ⅵ)的测定。     

Speciation analysis of chromium in natural water samples by electrothermal atomic absorbance spectrometry after separation/preconcentration with nanometer zirconium phosphate

A sensitive and simple method for the electrothermal atomic absorption spectrometry (ETAAS) determination of Cr(III) after separation/preconcentration on a micro-column packed with nanometer sized zirconium phosphate has been developed. Total chromium was determined after the reduction of Cr(VI) to Cr(III) by 10% (m/v) of aqueous ascorbic acid. The limit of detection for Cr(III) was 1.5 ng/L with an enrichment factor of 300. The static adsorption capacity of the sorbent for Cr(III) was 9.34 mg/g. The relative standard deviation was 3.2% (n = 7, c = 10 ng/mL). The method was applied successfully to the determination of Cr(III) and Cr(VI) in natural water samples.     

Cr(III) and Cr(VI) on-line preconcentration and determination with high performance flow flame emission spectrometry in natural samples

Methods for the on-line chromatographic preconcentration of Cr(III) and Cr(VI) have been developed. Cr(VI) has been preconcentrated on an RP C18 silica based column with tetrabutylammonium-bromide (TBABr) as ion-pairing agent. Specially for Cr(III) a new and effective preconcentration technique based on the sorption of Cr(III)-ions in a C18 column in presence of KH-phthalate has been developed. The efficiency of sample introduction into the atomic emission spectrometer could be improved by hydraulic high pressure nebulization. For the detection of chromium the acetylene/N(2)O flame has been used as a powerful emission spectrometric source. Applying these steps the detection limit (3sigma) could be improved to 25 pg/mL for Cr(III) and to 20 pg/mL for Cr(VI). The method has been applied for the chromium speciation in natural water samples.     

Chromium(III)-imprinted silica gel for speciation analysis of chromium in environmental water samples with ICP-MS detection

A new chromium(III)-imprinted 3-(2-aminoethylamino) propyltrimethoxysilane (AAPTS)-functionalized silica gel sorbent was synthesized by a surface imprinting technique and was employed as a selective solid-phase extraction material for speciation analysis of chromium in environmental water samples prior to its determination by inductively coupled plasma mass spectrometry (ICP-MS). The prepared Cr(III)-imprinted silica gel shows the selectivity coefficient of more than 700 for Cr(III) in the presence of Mn(II). The static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cr(III) were 30.5 mg g(-1) and 13.4 mg g(-1). It was also found that Cr(VI) could be adsorbed at low pH by the prepared imprinted silica gel, and this finding makes it feasible to enrich and determine Cr(VI) at low pH without adding reducing reagents. The imprinted silica gel sorbent offered a fast kinetics for the adsorption and desorption of both chromium species. Under the optimized conditions, the detection limits of 4.43 pg mL(-1) and 8.30 pg mL(-1) with the relative standard deviations (R.S.D.s) of 4.44% and 4.41% (C=0.5 ng mL(-1), n=7) for Cr(III) and Cr(VI) were obtained, respectively. The proposed method was successfully applied to the speciation of trace chromium in environmental water samples. To validate the proposed method, two certified reference materials were analyzed and the determined values were in a good agreement with the certified values. The developed method is rapid, selective, sensitive and applicable for the speciation of trace chromium in environmental water samples.