Pd/ZnO和Ag/ZnO复合纳米粒子的制备、表征及光催化活性

 用焙烧前驱物碱式碳酸锌的方法制备了ZnO纳米粒子，采用光还原沉积贵金属的方法制备了Pd／ZnO和Ag／ZnO复合纳米粒子，并利用ICP，XRD，TEM和XPS等测试技术对样品进行了表征，初步探讨了贵金属在ZnO纳米粒子表面形成原子簇的原因．以光催化氧化气相正庚烷为模型反应，考察了样品的光催化活性以及贵金属沉积量对催化剂活性的影响．结果表明：沉积适量的贵金属，ZnO纳米粒子光催化剂的活性大幅度提高．同时，深入探讨了表面沉积贵金属的ZnO纳米粒子光催化剂活性有所提高的内在原因．     

纳米WO3粉体的制备与光催化活性研究

报道了以钨酸钠和盐酸为主要原料，通过气液反应制备纳米WO3粉体光催化剂的新方法．在XPS，XRD，TEM等手段对催化剂进行了表征的基础上，又讨论了焙烧温度和乙醇加入量对催化剂粒度大小以及光催化活性的影响．同时对纳米WO3粉体催化剂的光催化重整乙醇制氢反应活性进行了研究，观察了产氢效率和光电化学行为．研究结果表明，气液反应法是一种简单有效的制备纳米WO3粉体催化剂的方法，并显示出较好的光催化活性；该方法所得的三氧化钨粉末粒子平均直径在100nm以下；钨酸钠溶液中乙醇加入量对三氧化钨粉末粒子的尺寸和分散性都有影响，随着乙醇量的增加，粒子尺寸减小，且分散性较好．焙烧温度引起的WO3粒子晶体结构的变化会导致光氧化还原电位变化，是引起光催化活性差异的主要原因．     

焙烧温度对ZnO粉体结晶及光学性能的影响

以草酸铵和醋酸锌为原料,采用直接沉淀法制备ZnO粉体,考察了焙烧温度对粉体结晶和光学性能的影响。 采用热重分析（TGA-DTA）、X射线衍射、紫外-可见漫反射（UV-Vis）、荧光分光光度计（FS）和扫描电子显微镜（SEM）等方法对样品进行了分析。 结果表明,制备的前驱物为C2O4Zn·2H2O,最低焙烧温度400 ℃,随着焙烧温度的提高,粉体结晶度提高,一次粒径增大;600 ℃焙烧后有较强紫外发光峰,粉体由200 nm的粒子排列成层叠状;900 ℃焙烧后有较强可见发光峰,粉体粒子大于500 nm,团聚严重;粉体有较强的紫外吸收,吸收峰有蓝移。     

焙烧温度对ZnO粉体结晶及其光学性能的影响

以草酸铵和醋酸锌为原料,采用直接沉淀法制备ZnO粉体,考察了焙烧温度对粉体结晶和光学性能的影响。采用热重分析(TGA-DTA)、X射线衍射、紫外-可见漫反射(UV-Vis)、荧光分光光度计(FS)和扫描电子显微镜(SEM)等方法对样品进行了分析。结果表明,制备的前驱物为C2O4Zn·2H2O,最低焙烧温度400℃,随着焙烧温度的提高,粉体结晶度提高,一次粒径增大;600℃焙烧后有较强紫外发光峰,粉体由200 nm的粒子排列成层叠状;900℃焙烧后有较强可见发光峰,粉体粒子大于500 nm,团聚严重;粉体有较强的紫外吸收,吸收峰有蓝移。     

Pd/ZnO和Ag/ZnO复合纳米粒子的SPS和XPS研究

用焙烧前驱物碱式碳酸锌的方法制备了ZnO纳米粒子，采用光还原沉积贵金属的方法分别得到了质量分数为0.5％的Pd/ZnO和Ag/ZnO复合纳米粒子，并利用XRD、TEM、XPS和SPS等测试技术对样品进行表征.初步探讨了贵金属在ZnO纳米粒子表面形成原子簇的原因及沉积贵金属对ZnO纳米粒子表面光电压信号的影响.以光催化氧化气相正庚烷为模型反应，考察了沉积贵金属对ZnO纳米粒子光催化活性的影响，并探讨了光催化活性有所提高的内在原因.结果表明， ZnO纳米粒子沉积贵金属后，其表面光电压信号明显下降，而光催化活性却大大地提高，这说明可以通过表面光电压谱的测试来初步的评估纳米粒子的光催化活性，即粒子的表面光电压信号越弱，其光催化活性越高.     

纳米粒子TiO2/Ti膜的表征及其光催化活性

以钛酸四丁酯为原料，采用溶胶－凝胶法，在600℃焙烧制备了纳米粒子TiO2/Ti膜，并利用TG－DTA，XRD、SEM、XPS、PL、SPS和EFISPS测试技术，对膜样品进行了表征。结果表明，纳米粒子TiO2/Ti膜表面为高密度的均匀碎片结构，TiO2纳米粒子具有与国际P-25TiO2粒子相类似的组成、结构以及微晶尺寸；在纳米粒子TiO2/Ti膜的表面，Ti主要以＋4价化学态存在。而O主要以晶格氧、羟基氧和吸附氧3种化学态存在。以纳米粒子TiO2／Ti膜的PL光谱测试中，以260nm为激发波长，观察到了峰位在380nm处的PL光谱，该值与SPS信号的响应阈值是一致的，此PL光谱峰可能与导带低的电子向价带顶的能级跃迁有关，同时说明了TiO2纳米粒子的量子尺寸效应的影响要大于库仑作用能和表面极化能的影响。以310nm为激发波长，分别观察到了与锐钛矿和金红石相关的发光信号；以450nm为激发波长，观察到了与表面态相关的弱的发光信号。此外，在光催化降解苯酚实验中，当涂膜3次时，TiO2粒子膜达到最高的光催化活性。     

纳米二氧化钛粉体及薄膜制备的研究进展

本文对近几年有关纳米二氧化钛粉体及薄膜的制备研究进行综述。重点介绍及评述了以无机钛盐和有机钛盐为前驱体制备纳米二氧化钛粉体及利用自组装方法制备二氧钛薄膜的最新研究成果。对今后研究工作的趋势进行了探讨。     

超声水解法制备的纳米二氧化钛光催化性能的研究

锐钛矿型纳米二氧化钛因其优良的光催化性能在环境保护中得到广泛应用，以TiCl4为钛源，水解过程中施加超声辐照，室温条件下制得了5～6nm锐钛型TiO2．考察了施加超声、煅烧温度及粒径尺寸对甲酸降解率的影响．结果表明，催化剂制备过程中施加超声影响对催化剂的光催化性能影响显著：甲酸的降解率由68.57％提高到97．13％．用超声水解法制备的纳米二氧化钛能够在较宽的煅烧温度范围里(450～650℃)保持较高的光催化活性．随粒径的减小催化剂活性提高。当粒径小于20nm时，显示量子尺寸效应。     

太阳光活性的铁酸铝-二氧化钛纳米复合光催化剂

以共沉淀法制备的铁酸铝和溶胶-凝胶法制备的二氧化钛粉体作为前驱体, 合成了铁酸铝-二氧化钛纳米复合材料, 通过曙红染料和甲基橙的光催化降解来评价该纳米复合材料的光催化活性, 并与单一二氧化钛的光催化性能进行了比较. 实验结果表明: 无论是紫外光还是太阳光的激发下, 铁酸铝-二氧化钛纳米复合材料的光催化活性均优于同样条件下所制备的单一二氧化钛纳米材料, 理想的铁酸铝掺杂浓度分别是1.0%(紫外光)和9.0%(太阳光). 由于在二氧化钛基体中掺入铁酸铝纳米粒子, 既可以促进光生载流子的电荷分离, 又可以使二氧化钛的光响应波长向可见光区域拓展, 提高了太阳能利用率, 从而使其在太阳光下具有更优越的光催化活性.     

ZnO纳米粒子的表面光电压谱和光催化性能

采用焙烧前驱物碱式碳酸锌的方法制备了不同粒径的ZnO纳米粒子，而用粒径 最小的作为光催化剂，通过光还原过程分别得了贵金属质量分数为0.5%和0.75%的 Pd/ZnO或Ag/ZnO复合纳米粒子。利用XRD，TEM，XPS，SPS和EFISPS等测试技术对样 品进行了表征，并通过光催化氧化气相正庚烷评估了样品的光催化活性，考察了微 晶尺寸和贵金属Pd或Ag的沉积对ZnO纳米粒子表面光电压信号以及光催化活性的影 响，探讨了样品表面光电压谱与其光催化活性的关系，说明了可以通过表面光电压 谱的测试来初步地评估纳米粒子的光催化活性。结果表明：随着ZnO纳米微晶尺寸 的减小，其SPS信号强度逐渐变弱，而光催化活性逐渐升高；沉积适量的贵金属Pd 或Ag后，ZnO纳米粒子的SPS信号强度明显下降，而其光催化活性却有所升高。此外 ，对ZnO纳米粒子光催化剂的失活机理进行了分析。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.