预处理条件对一步法合成吲哚用Ag/SiO2催化剂活性的影响

 以简单浸渍法制备的Ag/SiO2催化剂对苯胺和乙二醇一步法合成吲哚具有很高的催化活性. 研究了预处理条件对催化剂活性的影响. 结果表明,采用程序升温法将催化剂前体在500 ℃焙烧4 h,并在低于150 ℃时用H2-N2混合气(H2含量低于50%)原位还原得到的Ag/SiO2催化剂活性较高; TEM和XRD结果表明,预处理后催化剂表面银晶粒较小,结晶度较低.     

H3PW12O40/CNTs吸附-分解NOx及微波作用效果

将碳纳米管(CNTs)载体分别经混酸与硝酸蒸气预处理并在不同温度下煅烧, 然后分别采用浸渍法及机械研磨法负载磷钨酸(HPW), 制备出HPW/CNTs催化剂, 对比考察了上述催化剂对NOx的吸附与分解效果. 在空速为10000 h-1、 吸附温度为200℃的条件下, 用0.5 g催化剂对1696 mg/m3的NOx进行吸附实验, 结果表明, 以硝酸蒸气预处理且经300℃煅烧后的CNTs为载体, 采用机械研磨负载法制备的催化剂HPW/CNTs对NOx的吸附率与吸附能力最高, 分别为54%与16.6 mg NOx/(g\5h). 对吸附NOx后的催化剂体系进行了催化分解NOx的程序升温脱附-质谱(TPD-MS)研究, 结果表明, 所吸附的NOx在快速升温过程中发生分解, 在此过程中有氧产生, 分解产物包括N2, O2及N2O. 采用电阻炉快速加热与微波辐射2种方式分别对吸附的NOx进行催化分解, 结果表明, 微波功率为700 W时, NOx分解为N2的收率为33.3%, 高于电阻炉以150℃/min快速升温的N2收率. 使用过的催化剂通水蒸气后可实现再生, 对再生后的催化剂进行循环使用研究, 结果表明, 再生后的催化剂吸附与催化分解NOx的性能未有明显下降.     

Pt/CNTs催化剂的制备及其催化臭氧化活性研究

以碳纳米管(CNTs)为催化剂载体, 以H₂PtCl₆•6H₂O为贵金属活性组分前驱物, 采用等体积浸渍法制备了Pt/CNTs催化剂. 以草酸为目标污染物, 考察了所制备催化剂的催化活性, 并采用SEM, XRD和XPS等分析方法对催化剂进行表征. 对活性组分Pt的负载量、氢还原温度和热处理方式进行了研究, 确定了适宜的制备条件为Pt负载量1.0%、氢还原温度350 ℃. 研究表明, 在本实验条件下, 单独臭氧氧化、碳纳米管载体催化臭氧化和Pt/CNTs催化臭氧化分别能去除溶液中3.0%, 72.9%和97.9%的草酸. Pt的负载明显地提高碳纳米管催化臭氧化的效果. XRD分析显示催化剂的活性组分Pt以单质Pt⁰的形式存在; 与氢还原过程相比, 在空气气氛中焙烧制备的Pt/CNTs催化剂表面Pt的结晶度过高, 而且XPS结果表明此催化剂表面的Pt有化学吸附氧存在, 导致催化活性降低.     

碳纳米管负载Pd/SnO2催化剂的制备及其催化邻氯硝基苯加氢性能

采用化学还原法制备了不同Sn/Pd摩尔比的碳纳米管(CNTs)负载Pd/SnO2催化剂,并将该催化剂用于邻氯硝基苯(o-CNB)的选择加氢反应.采用透射电镜、X射线衍射和电感耦合等离子体技术对所制备的Pd/SnO2/CNTs催化剂进行了表征.结果表明,Sn/Pd摩尔比对该催化剂的邻氯硝基苯选择加氢反应性能影响显著.当Sn/Pd摩尔比为11时,催化剂的活性最高,在常压,60℃反应60 min,o-CNB转化率为96%.该催化剂还具有高的邻氯苯胺(o-CAN)选择性,o-CNB转化率达到100%时,脱氯副产物苯胺选择性小于5%.在相同条件下,浸渍法制备的2.4%Pd/CNTs催化剂上脱氯副反应严重,当o-CNB完全转化时,o-CAN选择性只有22%,副产物苯胺选择性则高达78%.     

碳纳米管对Rh-Ce-Mn/SiO2催化剂催化CO加氢合成含氧化合物性能的影响

 制备了碳纳米管(CNTs)促进的Rh-Ce-Mn/SiO2催化剂,采用X射线光电子能谱、程序升温还原、 N2物理吸附、 X射线衍射以及吸附H2或CO的程序升温脱附对催化剂进行了表征,并考察了催化剂对CO加氢合成含氧化合物的催化性能. 结果表明, CNTs的添加促进了铑的分散,铑及助剂在载体表面发生富集; 活性组分铑与助剂及载体间的相互作用和催化剂样品的还原性能发生了改变; 在铑基催化剂中加入CNTs后,强吸附的H2和CO的量明显增大. CNTs促进的铑基催化剂的CO加氢活性明显提高,当CNTs添加量为10%时,一定条件下催化剂上含氧化合物的时空收率可达336.2 g/(kg·h).     

Pt/RuO2/CNTs纳米催化剂中RuO2含量对甲醇电催化氧化性能的影响

制备了一种新的甲醇直接燃料电池Pt/RuO2/CNTs阳极催化剂,在相同Pt负载量下,其甲醇电催化氧化活性是Pt/CNTs的3倍.采用循环伏安法研究发现Pt/RuO2/CNTs纳米催化剂中RuO2含量对甲醇电催化氧化活性有明显影响,当Pt和RuO2在碳纳米管上含量分别为15%和9.5%时,Pt/RuO2/CNTs催化剂具有最佳的甲醇电催化氧化活性.RuO2负载在碳纳米管上比电容的变化,反映了水合RuO2结构中质子与电子传输平衡的能力,分析表明,催化剂中RuO2含量不同导致电容的变化是影响甲醇电催化氧化活性的主要原因.当催化剂结构中质子与电子传输达到平衡时,催化剂比电容最大,电催化氧化活性最高.这种基于电容关联电催化剂的观点对甲醇直接燃料电池阳极催化剂的设计非常有意义.     

激光溅射法制备Pt/CNTs催化剂用于邻氯硝基苯的液相加氢反应

采用激光溅射法制备了碳纳米管负载铂(Pt/CNTs)催化剂, 并利用透射电子显微镜(TEM)、X射线能量散射谱(EDS)、X射线衍射(XRD)、X射线光电子能谱(XPS)等表征手段研究了Pt粒子在碳纳米管表面存在的状态、组成、结构等性质. 讨论了Pt/CNTs催化剂的不同制备条件对催化剂结构的影响, 并考察了催化剂对邻氯硝基苯液相加氢合成邻氯苯胺反应的加氢性能. 研究结果表明, 在激光电压为250 V, 绝对压力为300 Pa, 载体温度为25 ℃条件下制备的Pt/CNTs催化剂, 在不加脱卤抑制剂, 反应温度为60 ℃和氢气压力为1.0 MPa的条件下, 邻氯硝基苯转化率可以达到99.7%以上, 邻氯苯胺选择性可达到98.2%以上, 表现出较高的加氢性能和抑制脱卤性能.     

水热预处理合成Bi0.5Y0.5VO4及其光解水性能研究

采用水热反应预处理法制备了Bi0.5Y0.5VO4光催化剂,考察了预处理条件及焙烧温度对光催化活性的影响.利用XRD、SEM、UV-vis和BET等测试手段对样品的晶相组成、表面形貌、光吸收性能和比表面积等物理性质进行了表征.结果表明:预处理后可在温和条件下合成Bi0.5Y0.5VO4(BYV)固溶体,当水热预处理条件为pH=1,焙烧温度为800℃时制备材料活性最高,共负载Pt-Cr2O3助催化剂后具有完全分解水性能,生成氢气和氧气的量分别为80.5μmol/h和43.8μmol/h.     

酸化膨润土负载金催化剂用于CO氧化

用盐酸和硫酸对膨润土（Ben）进行改性处理,采用浸渍法（IMP）、沉积-沉淀法（DP）和阳离子吸附法(CA)制备改性膨润土负载的金催化剂,以CO氧化作为探针反应对催化剂的催化性能进行了研究,采用BET、XRD、TEM和TPD等对催化剂进行表征。 结果表明,经过简单的酸处理后的膨润土比表面积和孔体积有了大幅度的提高,硫酸酸化的膨润土作为载体较之盐酸酸化土更容易得到活性较高的金催化剂,XRD粒径计算结果和TEM观察结果证明,硫酸酸化的膨润土作为载体相比盐酸酸化土可以得到Au颗粒度更小的催化剂。 不同制备方法中,阳离子吸附法能较好的将Au负载于膨润土载体上,得到小颗粒的金催化剂,且在吸附48 h、450 ℃焙烧、150 ℃下H2还原的预处理条件下得到的催化剂活性最好。     

CuO-MnO2/Al2O3 催化臭氧化催化剂的制备、结构表征及性能

采用浸渍法,以Al2O3为载体制备了氧化铜和二氧化锰复合的双组分负载型金属催化臭氧化催化剂.以松花江水的UV254去除率作为催化剂活性指标,通过正交试验,确定了催化剂的最佳制备条件.实验结果表明,催化剂的最佳制备条件如下:浸渍5h,活性组元体积比为3:1,于90℃干燥2h,于200℃焙烧3h.采用扫描电镜对催化剂的结构进行了表征;通过TG-DTA测试分析了催化剂热分解过程的反应速率、热效应和物质变化过程;运用XPS分析了催化剂表面元素的组成、元素相对含量和元素价态.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。