共查询到20条相似文献,搜索用时 62 毫秒
1.
利用超临界萃取(SFE)测定聚丙烯酸盐吸水性树酯中残留单体含量 总被引:1,自引:0,他引:1
采用超临界萃取分离聚丙烯酸盐中的单体,对影响萃取分离效率的三个主要因素:温度、压力、改性剂进行了筛选,建立了测定聚丙烯酸盐中单体含量的分析方法,此法标准物添加回收率为932%~948%。 相似文献
2.
反相悬浮聚合法合成超强吸水剂 总被引:12,自引:1,他引:11
探讨采用反相悬浮聚合法、合成聚丙烯酸盐超强吸水剂的工艺条件。结果表明:反应液中和废、单体浓度反应引发温度及交联剂种类及用量,对聚合反应的稳定进行有着很大的影响。采用本法制成的超强吸水剂,其吸去离子水能力达1200-1400g/g。制成的吸水剂凝胶粒子有一定的粒径分布。 相似文献
3.
(ML0.70Mg0.12Zr0.07Gd0.05MY0.06)Ni2.87Al0.08Co0.15是具有快速充电能力的AB3型负极合金材料,将此负极合金与正极以及尼龙或聚丙烯隔膜组成的快充形MH-Ni电池,研究了负极合金与隔膜的相互匹配性。结果表明:用交联型聚丙烯酸盐对隔膜改性生成的聚丙烯隔膜与该AB3型负极合金有良好的匹配性。 相似文献
4.
5.
6.
聚丙烯/层状硅酸盐纳米复合材料的制备、结构和性能 总被引:10,自引:0,他引:10
聚丙烯/层状硅酸盐纳米复合材料可通过丙烯单体插层聚合、聚丙烯溶液插层和聚丙烯熔融插层等方法制备,得到插层型或剥离型纳米复合材料,形成了与传统填充型聚合物复合材料不同的微观结构,其机械性能,热性能,阻隔性能和流变性能等明显提高,由于聚丙烯的非极性及层状硅酸盐纳米复合材料制备方法的特殊性,该研究具有一定的理论价值。 相似文献
7.
细旦聚丙烯卷绕丝的结晶结构与其后拉伸性能的关系 总被引:1,自引:0,他引:1
应用电子计算机对一系列细旦聚丙烯卷绕丝样品的大角X射线衍射图进行分峰处理,发现用常规熔融纺丝制得的聚丙烯卷绕丝的X射线衍射曲线可以分解成六个峰:一个非晶峰,对应于α晶型的三个典型峰(2θ值分别为14.0°,16.8°,18.5°),对应于次晶的典型的二个峰(20=15.2°,21.4°)。对样品中所含次晶和α晶相对含量与其后拉伸性能相互关系的研究结果表明:卷绕丝次晶对α晶的相对含量越高,后拉伸性能越好。这将有助于选择合适的纺丝工艺条件,制备具有优良物理机械性能的细旦聚丙烯长丝。 相似文献
8.
研究了两种马来酸酐接枝聚丙烯(PP-g-MAH)在不同含量时对聚丙烯(PP)/滑石粉复合材料的力学性能、雾化性能和线性膨胀系数的影响.结果表明,接枝物的加入能提高复合材料的拉伸性能、冲击性能和弯曲性能,但随着含量的增加拉伸强度、冲击强度和弯曲强度及弯曲模量有所降低.在含量相同时,接枝物1对冷凝组份的影响更小.复合材料的线性膨胀系数随接枝物含量的增加先减小后增加. 相似文献
9.
10.
采用重量法和光泽度法检测改性聚丙烯雾化性能,研究了试样形式和不同溶剂对检测结果的影响。结果表明,采用重量法时,料粒冷凝组份G比圆片高,故圆片雾化性能好,且不同溶剂对改性聚丙烯材料冷凝组份G的增加程度受组分分压、体系总压和组分间相互干扰的影响;采用光泽度法时,料粒雾化值FJ比圆片低,故圆片雾化性能好,且不同溶剂对改性聚丙烯材料雾化值FJ的降低程度受组分分压、体系总压和组分间相互干扰的影响;雾化重量法和光泽度法测试结果不具备可比性。此外,邻苯二甲酸二辛酯标样放置时间对重量法结果有较大影响。 相似文献
11.
Cline Farcet Julien Nicolas Bernadette Charleux 《Journal of polymer science. Part A, Polymer chemistry》2002,40(24):4410-4420
The controlled free‐radical homopolymerization of n‐butyl acrylate was studied in aqueous miniemulsions at 112 and 125 °C with a low molar mass alkoxyamine unimolecular initiator and an acyclic β‐phosphonylated nitroxide mediator, N‐tert‐butyl‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl) nitroxide, also called SG1. The polymerizations led to stable latices with 20 wt % solids and were obtained with neither coagulation during synthesis nor destabilization over time. However, in contrast to latices obtained via classical free‐radical polymerization, the average particle size of the final latices was large, with broad particle size distributions. The initial [SG1]0/[alkoxyamine]0 molar ratio was shown to control the rate of polymerization. The fraction of SG1 released upon macroradical self‐termination was small with respect to the initial alkoxyamine concentration, indicating a very low fraction of dead chains. Average molar masses were controlled by the initial concentration of alkoxyamine and increased linearly with monomer conversion. The molar mass distribution was narrow, depending on the initial concentration of free nitroxide in the system. The initiator efficiency was lower than 1 at 112 °C but was very significantly improved when either a macroinitiator was used at 112 °C or the polymerization temperature was raised to 125 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4410–4420, 2002 相似文献
12.
13.
14.
15.
可控自由基聚合与其它聚合方法结合,可以制备多种类型的嵌段共聚物,因此得到了广泛关注。本文着重介绍可控自由基聚合与离子开环聚合、阴离子聚合、烯类单体的阳离子聚合及其它活性聚合方法结合制备嵌段共聚物的研究现状和进展。 相似文献
16.
17.
18.
由可控聚合,包括活性阴离子和自由基聚合直接制备不同形貌纳米材料,是近几年来合成化学领域的一个重要研究成果.与两亲性嵌段共聚物在选择性溶剂中自组装方法不同,在选择性溶剂中进行的分散聚合,首先生成两亲性嵌段共聚物,并逐渐增加第二段聚合物的链长,以实现相分离,形成球形胶束;聚合物链继续增长,实现形貌转变,从而制备预期的聚合物形貌,包括球形胶束、纳米棒、纳米线、囊泡和复合囊泡等.本文综述了乳液聚合法制备球形胶束等形貌;描述了不同聚合体系形成的形貌以及它们的性质和应用,讨论了形貌的形成机理和控制方法,同时指出了存在的问题. 相似文献
19.
20.
Kevin M. Burridge Nethmi De Alwis Watuthanthrige Camryn Payne Richard C. Page Dominik Konkolewicz 《Journal of polymer science. Part A, Polymer chemistry》2021,59(21):2530-2536
An enduring question is: what is the simplest and easiest way to obtain tailored polymers? This communication explores a robust photoiniferter polymerization with only two active ingredients that requires no prior deoxygenation and can be performed on the milliliter scale or sub-milliliter scale. Rather than leaving headspace in the polymerization vessel or scaling reactions up to fill the vessel, this approach fills the headspace of the reaction vessel with mineral oil or inert solvents. This approach can also be applied to polar monomers in aqueous media, using oil as the inert solvent, or to hydrophobic monomers with water as the inert solvent. This method removes enough ambient oxygen that the photoiniferter reaction proceeds with no deoxygenation step, and achieves high conversion and good molecular weight control in 10–20 h in both aqueous and organic solvents. Complex polymer architectures such as multiblock copolymers and gradient polymers were successfully synthesized by this approach. 相似文献