离聚物Surlyn对PBT/PP共混体系的力学性能及形态结构的影响

用力学性能测试、ＤＭＡ、ＳＥＭ等方法研究了离聚物Ｓｕｒｌｙｎ对ＰＢＴ／ＰＰ共混体系的力学性能及形态结构的影响。结果表明，在ＰＢＴ／ＰＰ共混体系中引入少量Ｓｕｒｌｙｎ可以改善界面的粘接性，从而改善其力学性能。当共混体系中ＰＢＴ／ＰＰ的组份比不变（９０／１０）且Ｓｕｒｌｙｎ的含量为６ｐｈｒ左右时，共混物的冲击强度出现极大值；而弯曲强度在Ｓｕｒｌｙｎ含量为１－２ｐｈｒ左右时有最大值。当共混体系中Ｓｕｒｌｙｎ的含量不变（６ｐｈｒ）时，其力学性能随ＰＰ含量的增加而下降。用玻璃纤维增强共混体系，可显著提高力学性能。     

酞侧基聚芳醚砜／聚苯硫醚共混物的形态与力学性能

酞侧基聚芳醚砜（ＰＥＳ－Ｃ）与聚苯硫醚（ＰＰＳ）具有部分相容性，虽然ＰＰＳ的强度和韧性均低于ＰＥＳ－，但ＰＰＳ含量为２％～１０％的ＰＥＳ－Ｃ／ＰＰＳ共混物在保持ＰＥＳ－Ｃ原有强度，断裂伸长率的同时，模量略增，冲击强度有很大幅度提高，熔融指数亦蛔。     

纳米刚性微粒与橡胶弹性微粒同时增强增韧聚丙烯的研究

通过力学性能测试、动态力学试验、ＤＳＣ 分析以及材料断面形貌与结构分析等手段,对以纳米二氧化硅（ＳｉＯ２） 为刚性微粒、以三元乙丙橡胶（ＥＰＤＭ） 为弹性微粒组成的聚丙烯（ＰＰ）／ 纳米ＳｉＯ２／ＥＰＤＭ 的同时增强增韧效果进行了研究．结果显示,上述两种微粒可同时大幅度提高ＰＰ 的韧性、强度和模量,当ＰＰ／ 纳米ＳｉＯ２／ＥＰＤＭ 为８０／３／２０ 时,两种微粒体现较明显的协同增韧效应．纳米ＳｉＯ２ 可提高ＰＰ 的结晶温度和结晶速度,并使球晶细化．纳米ＳｉＯ２ 刚性微粒在ＰＰ连续相中以微粒团聚体形态分布,构成团聚体的平均微粒数约为６ ～７ ,其与ＰＰ基体表现出较强的结合牢度．ＰＰ／ 纳米ＳｉＯ２／ＥＰＤＭ 的综合性能已接近或达到工程塑料的性能．     

液晶嵌段共聚物PET/60PHB-b-PC的合成及结构与性能

采用ＰＥＴ齐聚物的原位乙酰化法通过加入少量乙二醇（ＥＧ）合成了端羟基液晶聚合物ＰＥＴ／６０ＰＨＢ，并将其作为大单体，与双酚Ａ及碳酸二苯酯通过熔融酯交换法，进一步制得了液晶嵌段共聚物ＰＥＴ／６０ＰＨＢ ｂ ＰＣ．研究了合成规律，并借助粘度测定、ＤＳＣ、偏光显微镜、Ｘ 光衍射和红外光谱分析等手段对合成的液晶嵌段共聚物进行了表征．研究表明，当ＰＥＴ齐聚物的ηｉｎｈ＝００５～００７ｄＬ／ｇ，Ａｃ２Ｏ／ＰＨＢ（ｍｏｌ／ｍｏｌ）＝１３，ＥＧ／ＰＥＴ（ｍｏｌ／ｍｏｌ）＝００６时能获得颜色、液晶性、溶解性均很好的端羟基液晶聚合物ＰＥＴ／６０ＰＨＢ，以此液晶聚合物为原料，采用合适的配方与工艺，能获得粘度较高、液晶性较好，并且熔体流动性很好的液晶嵌段共聚物ＰＥＴ／６０ＰＨＢ ｂ ＰＣ．通过偏光显微镜与Ｘ 光衍射观察，证明此嵌段共聚物呈现向列型液晶织构，但其液晶态织构与纯ＰＥＴ／６０ＰＨＢ、ＰＥＴ／６０ＰＨＢ和ＰＣ的混合物明显不同．此外，还初步建立了用红外的分析手段鉴定液晶聚合物ＰＥＴ／６０ＰＨＢ端基的方法．     

甲基丙烯酸甲酯 - 甲基丙烯酸共聚物/梯形聚苯基硅倍半氧烷原位共混体系的性能研究

甲基丙烯酸甲酯 甲基丙烯酸共聚物（Ｐ（ＭＭＡ ＭＡＡ））与低分子量或高分子量梯形聚苯基硅倍半氧烷（ＰＰＳＱ）的共混物经原位聚合法制成．用光学透明法、荧光光谱、ＤＳＣ等技术研究了该共混体系的相容性及组分间的相互作用及结构转变．结果表明，当ＰＰＳＱ含量较小时，由于ＰＰＳＱ与Ｐ（ＭＭＡ ＭＡＡ）间存在着较强的氢键作用，该共混体系在一定配比下相容，且低分子量ＰＰＳＱ与Ｐ（ＭＭＡ ＭＡＡ）间的相容性较好．当ＰＰＳＱ的含量≤１％时，ＰＰＳＱ的加入对该共混物的Ｔｇ影响不大，但其Ｔｆ随ＰＰＳＱ含量增加而增大．此外，还测试了Ｐ（ＭＭＡ ＭＡＡ）／ＰＰＳＱ原位共混物的硬度及冲击强度．     

引入离子基团改善聚苯乙烯和热致液晶聚合物的相容性 Ⅰ热性能和形态

ＤＳＣ和ＳＥＭ研究结果表明聚苯乙烯（ＰＳ）与一种热致液晶聚合物（ＬＣＰ）（ＰＨＢ／ＰＥＴ（６０／４０）共聚酯）完全不相容．共混体系具有与组分无关的Ｔｇ，并且表现出明显的两相结构．将ＰＳ进行化学改性（引入磺酸基团）制备成磺化聚苯乙烯（ＳＰＳ），随中和盐离子的变化有：酸式、Ｌｉ、Ｎａ、Ｚｎ和Ｍｎ盐五种形式．用ＤＳＣ和ＳＥＭ对ＬＣＰ与ＳＰＳ共混物的热性能和形态进行了分析和表征．共混体系有一个与组成相关，且明显低于纯ＳＰＳ的Ｔｇ．这表明了ＰＳ与ＬＣＰ的相容性因为磺酸基团的引入而得到了改善．同时用Ｆｏｘ方程计算了ＬＣＰ的Ｔｇ．当ＳＰＳ含量较低时（不大于５０％）在各个共混体系中，所估算的ＬＣＰ的Ｔｇ相互吻合．表明共混体系满足Ｆｏｘ方程的前提条件，即ＬＣＰ与ＳＰＳ形成相容体系．当ＳＰＳ含量较低时（２５％），ＬＣＰ／ＳＰＳ的共混物为较均一体系，断面光滑；而ＳＰＳ含量较高时，在脆断面可以观察到纳米级的颗粒．电子能谱分析证明了这些颗粒是ＳＰＳ负离子的聚集体．     

聚乙二醇改性聚对苯二甲酸乙二酯／聚对苯二甲酸丁二酯共混体系研究 Ⅱ．结晶形态和分子量及动态力学性能

本文研究工作表明，聚乙二醇（ＰＥＧ）作为聚对苯二甲酸乙二酯（ＰＥＴ）／聚对苯二甲酸丁二酯（ＰＢＴ）共混体系的结晶促进剂．不仅使聚合物分子链运动容易而有利于结晶时定向排列，晶体生成速度加快．而且使成核剂的成核效率提高，晶核生成速度加快，晶核数目增多而晶体尺寸减小．此外，ＰＥＧ还部分参与了聚酯的酯交换反应，在低用量时有利于聚合物特性粘数提高，而用量增大则引起聚酯降解．由于ＰＥＧ的这些作用，共混体系在ＰＥＧ为６．０％时的模量及γ－衰减强度最大．动态力学性能最好．     

聚丙撑碳酸酯增韧环氧树脂的研究

研究了聚丙撑碳酸酯（ＰＰＣ）对环氧树脂（ＥＰ）的改性作用、加入２０～３０Ｐｈｒ的ＰＰＣ，环氧树脂力学性能可以大幅度提高，粘接剪切强度为１２３３ＭＰａ，冲击强度为１６．７８ｋＪ／ｍ２；而纯环氧树脂固化物，其剪切强度为９．３６ＭＰａ，冲击强度为９．９９ｋＪ／ｍ２。ＳＥＭ和ＤＳＣ观测表明ＰＰＣ／ＥＰ体系呈两相结构。     

聚对苯二甲酸乙二酯／热致液晶聚合物共混体系中液晶组分的诱导结晶效应

用差示扫描量热法对聚对苯二甲酸乙二酯（ＰＥＴ）／热致液晶高分子（ＬＣＰ）共混体系的等温和非等温结晶行为进行了研究．结果表明，由于液晶组分的加入，共混体系中ＰＥＴ的结晶速率和结晶度均得到提高．说明ＬＣＰ具有ＰＥＴ结晶成核剂的作用．在较低的ＬＣＰ组分含量下（～２ｗｔ％），这一效果最为明显，说明ＬＣＰ是以很小的微区或某些ＬＣＰ分子链介晶微束的形式对ＰＥＴ的结晶起成核剂的作用．     

结晶／结晶共混体系PPS／PEEK中PPS组分的结晶熔融行为（Ⅱ）──熔融条件对退火样品的影响

结晶／结晶共混体系ＰＰＳ／ＰＥＥＫ中ＰＰＳ组分的结晶熔融行为（Ⅱ）──熔融条件对退火样品的影响麦堪成，许家瑞，梅震，曾汉民（广州中山大学材料科学研究所，广州，５１０２７５）关键词聚苯硫醚，聚醚醚酮，结晶熔融行为，熔融双峰聚苯硫醚（ＰＰＳ）的结晶熔融行...     

增容剂对聚对苯二甲酸乙二酯/聚丙烯共混体系结构流变学的影响

采用马来酸酐接枝聚丙烯(PP-g-MAH)对聚丙烯/聚对苯二甲酸乙二酯(PP/PET)共混体系进行增容,研究了增容前后复合体系的相形态和流变行为的变化.结果表明,共混体系中当PP组分为分散相时,增容剂能够显著减小PP液滴尺寸,使其形状松弛时间减小,变形与破裂的剪切敏感性降低;当共混体系两组分配比处于临界相反转点周围时,增容剂则会导致其内部部分双连续与“海-岛”结构共存的复杂相形态消失,低频区模量频率依赖性的增加表明体系内部界面结合程度的增加;而当共混体系中的PET组分为分散相时,增容剂的引入对体系结构流变学影响较小,表明增容效果不大.     

Morphology and nonisothermal crystallization of in situ microfibrillar poly(ethylene terephthalate)/polypropylene blend fabricated through slit‐extrusion,hot‐stretch quenching

This study describes the morphology and nonisothermal crystallization kinetics of poly(ethylene terephthalate) (PET)/isotactic polypropylene (iPP) in situ micro‐fiber‐reinforced blends (MRB) obtained via slit‐extrusion, hot‐stretching quenching. For comparison purposes, neat PP and PET/PP common blends are also included. Morphological observation indicated that the well‐defined microfibers are in situ generated by the slit‐extrusion, hot‐stretching quenching process. Neat iPP and PET/iPP common blends showed the normal spherulite morphology, whereas the PET/iPP microfibrillar blend had typical transcrystallites at 1 wt % PET concentration. The nonisothermal crystallization kinetics of three samples were investigated with differential scanning calorimetry (DSC). Applying the theories proposed by Jeziorny, Ozawa, and Liu to analyze the crystallization kinetics of neat PP and PET/PP common and microfibrillar blends, agreement was found between our experimental results and Liu's prediction. The increases of crystallization temperature and crystallization rate during the nonisothermal crystallization process indicated that PET in situ microfibers have significant nucleation ability for the crystallization of a PP matrix phase. The crystallization peaks in the DSC curves of the three materials examined widened and shifted to lower temperature when the cooling rate was increased. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 374–385, 2004     

The β-nucleated ternary composites of polypropylene/nano-CaCO3/short poly(ethylene-terephthalate) fiber

A serial of β-nucleated polypropylene (β-PP)/nano-calcium carbonate (nano-CaCO₃)/ short poly(ethylene-terephthalate) (PET) fiber composites were prepared using extrusion blending. Maleic anhydride grafted PP (PP-g-MA) was used to modify the compatibility. The relationships among components, structure, and properties of the PP composites were studied. The results show that adding nano-CaCO₃ improved the mechanical properties of the materials. Adding PET fiber increased the rigidity and toughness but the tensile strength decreased. PP-g-MA modified the compatibility of the components of the composites. Both PET fiber and nano-CaCO₃ had nucleation effect on the PP crystallization and slightly induced the formation of β crystals. Ternary β-PP/nano-CaCO₃/PET fiber composites contained high β-crystal content, and the compatibilizer exhibited synergy effect with β nucleating agent to further increase the β-crystal content in the blends. Mo’s method could satisfactorily describe the nonisothermal crystallization behavior of ternary composites, whereas Jeziorny and Ozawa methods failed to do the same ideally.     

A study of PP/PET composites: Factorial design,mechanical and thermal properties

Due to the economic importance of polypropylene (PP) and polyethylene terephthalate (PET), and the large amount of composites made with PP matrix and recycled PET as reinforcing material; an investigation was performed regarding the mechanical and thermal behavior of PP composites containing recycled polyethylene terephthalate fibers (rPET). Interfacial adhesion between the two materials was achieved by adding a compatibilizer, maleic anhydride grafted polypropylene, PP-g-MA. Mechanical behavior was assessed by tensile, flexural, impact and fatigue tests, and thermal behavior by HDT (Heat Deflection Temperature). Fractured surfaces and fiber were investigated by scanning electron microscopy. Multiple regression statistical analysis was performed to interpret interaction effects of the variables. Tensile strength, tensile modulus, flexural strength, flexural modulus and HDT increased after rPET fiber incorporation while strain at break, impact strength and fatigue life decreased. Addition of compatibilizer increased tensile strength, flexural strength and flexural modulus, fatigue life and HDT while tensile modulus, strain at break and impact strength decreased. However, at low fiber content, the impact strength increased, probably due to nucleation effects on PP.     

Mechanical properties and characteristic of surface treated bamboo fiber reinforced PP/PS blends

Bamboo fiber (BF) as organic filler is characterized by mechanical properties analysis and morphology examination for polypropylene (PP) and polystyrene (PS) matrix blends. Effects of different filler content on tensile strength, flexural properties, and impact strength are proposed. It is observed from scanning electron microscopy (SEM) studies that addition of BF is beneficial in increasing mechanical strength via increasing the interface dispersed phase. The optimum tensile properties and impact properties of BF content were at 40 wt% for PP/PS/BF composite on melt mixing conditions. The results showed a significant improvement in mechanical properties of PP/PS/BF ternary blend composite. Comparing with untreated BF, content of carbon and nitrogen of treated BF decreased to 66.57 and 2.31%, oxygen content increased to 21.07%, and silicon content increased from 0 to 10.04%. The element ratio of O/C, N/C, and Si/C changed to 31.65, 3.47, and 15.08, respectively.     

Effect of dispersed phase composition on morphological and mechanical properties of PET/EVA/PP ternary blends

Immiscible ternary blends of PET/EVA/PP (PET as the matrix and (PP/EVA) composition ratio = 1/1) were prepared by melt mixing. Scanning electron microscope results showed core‐shell type morphology for this ternary blend. Binary blends of PET/PP and PET/EVA were also prepared as control samples. Two grades of EVA with various viscosities, one higher and the other one lower than that of PP, were used to investigate the effect of components' viscosity on the droplet size of disperse phase. The effect of interfacial tension, elasticity, and viscosity on the disperse phase size of both binary and ternary blends was investigated. Variation of tensile modulus of both binary and ternary blends with dispersed phase content was also studied. Experimental results obtained for modulus of PET/EVA binary blends, showed no significant deviations from Takayanagi model, where considerable deviations were observed for PET/PP binary blends. Here, this model that has been originally proposed for binary blends was improved to become applicable for the prediction of the tensile modulus of ternary blends. The new modified model showed good agreement with the experimental data obtained in this study. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 251–259, 2010     

Effect of viscosity ratio on the morphology of PET microfibrils in uncompatibilized and compatibilized drawn PET/PP/TiO2 blends

Uncompatibilized and compatibilized (polypropylene‐grafted maleic anhydride (PP‐g‐MA) as compatibilizer) PET (polyethylene terephthalate)/PP (polypropylene)/TiO₂ drawn strands were prepared by extrusion of the blends and cold drawing of the extrudates. In the uncompatibilized drawn strand, the generated PET microfibrils show large aspect ratio and wide distribution in diameter; whereas in the compatibilized drawn strand numbers of short needle‐like PET formations appear and demonstrate uniform diameter distribution. Derived from PET droplets, the microfibril morphology is greatly influenced by the size of PET droplets in the extrudates: small droplet deforms into needle‐like shape and large one becomes microfibril. In the compatibilized PET/PP/TiO₂ extrudate, the size of PET droplet is much smaller than that in the uncompatibilized one. The reduction of droplet size is attributed to the low viscosity ratio between dispersed phase and matrix, which facilitates the break up of the dispersed PET droplets. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 555–562, 2009     

Effect of draw ratio on the microstructure, thermal, tensile and dynamic rheological properties of insitu microfibrillar composites

Microfibrillar composites (MFCs) were prepared using different draw/stretch ratios [viz. 2, 5, 8 and 10] from polypropylene/polyethylene terephthalate (PP/PET) blends. Scanning electron microscopy [SEM] images revealed that PET microfibrils were highly oriented after melt blending and drawing. After the conversion of drawn (stretched) blends to MFCs the PET microfibrils were found to be randomly distributed in the PP matrix. The tensile strength and modulus of the MFCs were found to be higher for the samples drawn at stretch ratios 5 and 8 on account of the long PET microfibrils they possessed. The non isothermal crystallization behaviour of the neat blend (as extruded), stretched blend and the MFC was compared. The oriented PET fibrils in the stretched blend were found to have a greater nucleating effect for the crystallization of PP than the spherical PET particles in the neat blend and randomly oriented short PET fibrils in the MFC. Dynamic rheology studies indicated the storage modulus and loss modulus of MFCs were enhanced as draw ratio increases up to an optimized level beyond which they decrease. When the draw ratio increased up to the optimized level the MFCs tended to be more viscous, especially at low frequency, whereas further increasing the draw ratio resulted in a decrease in the complex viscosity. The microfibrils of PET in the MFC were found to perturb the relaxation of molten PP matrix.     

PBT/POE-g-MAH/PP共混体系的相态结构与性能

采用马来酸酐接枝乙烯-辛烯共聚物弹性体(POE-g-MAH)与聚丙烯(PP)在双螺杆挤出机上进行熔融共混,制备了3种新型增韧改性剂.研究了增韧改性剂的种类及其用量对共混物的力学性能、相形态结构、熔融与结晶行为的影响.力学性能测试表明,POE-g-MAH与适量PP并用具有显著的协同增韧作用,当POE-g-MAH与PP的配比为70/30时,所得增韧改性剂(POEg2)具有最佳的增韧效果.当POEg2含量达到15%时,共混物的缺口冲击强度(Is)从纯PBT的7.5 kJ/m2提高到51.2 kJ/m2,与15%的纯POE-g-MAH弹性体增韧PBT具有相近的缺口冲击强度值.同时,共混物的拉伸强度(σb)损失最小.采用AFM和SEM观察发现,新型增韧改性剂作为分散相具有软壳-硬核结构.DSC测试表明,随增韧改性剂中PP含量增加到一定值时,壳-核结构中软壳层出现不完整现象,导致界面作用力减小,共混物的Is和σb都出现明显下降.     

HDPE/PP共混物在振动剪切作用下的力学性能与形态控制

采用高剪切引起的相容与振动剪切保压方式控制共混物的形态,结果表明,当共混体系中HDPE/PP为92/8时的试样拉伸强度为97.1MPa,而80/20试样的缺口冲击强度为45.5kJ/m₂,较静态试样分别提高4.3倍和9.5倍.采用振动剪切注射技术可以针对某一组分获得高强度、高韧性的HDPE/PP共混制件.