A New Quaternary Ammonium Heteropolyoxotungstate Catalyst for Propylene Epoxidation to Propylene Oxide

A new quaternary ammonium heteropolyoxotungstant (cat.C) is prepared and characterized. And the cat.C also is an reaction-controlled phase-transfer catalyst. The catalytic system of O2/EAHQ (2-ethylanthrahydroquinone)/cat.c is used for the epoxidation of propylene. Under the optimal conditions, the yield of propylene oxide based on EAHQ is 84.1%, theselectivity for propylene oxide based on propylene is 99.8% and the conversion of propylene based on EAHQ is 84.3%. The cat.c precipitates after the epoxidation reaction for easy separation. The cat. C is stable enough to be recycled three times without any loss in selectivity.     

Study on Chemisorption, Catalytic Behavior, and Stability of Supported Au Catalyst for the Propylene Epoxidation Reaction

The supported Au/TiO2 and Au/TiO2-SiO2 catalysts were prepared by deposition precipitation method. The TPD study reveals that propylene oxide competes with propylene to be adsorbed on the same adsorptive center-Tin site on the surface of the catalyst and that the adsorbing capacity of the catalyst for propylene oxide is larger than that for propylene. Catalytic behavior for propylene epoxidation with H2 and O2 was tested in a micro-reactor. Under typical conditions, the selectivity for propylene oxide is over 87%. The TG curves show that PO successive oxidation cause carbon deposition on the active center and deactivation of the Au catalysts. Because the amounts of Tin site decrease significantly, and consequently the separation between Tin sites increases, the Au/TiO2-SiO2 catalyst is more stable than Au/TiO2.     

Propylene Dimerization by（η^5—C9H7）2 Nickel（Ⅱ）Catalytic System

The catalytic performance of Ni(η^5-Ind)2 complex in the dimerization of propylene was studied in combimation with an organoaluminum co-catalyst,eventually in the presence of a phosphine ligand.The effects of the type of aluminum co-catalyst and its relative amount,the nature of phosphine ligand and P/Ni ratio as well as the reaction temperature were examined.The results indicated that the nickel precatalyst exhibited high productivity for the propylene dimerization together with organoaluminum.It was likely to strongly modify the reactivity in the catalytic sytem when using phosphine ligand as additives,especially at the reaction temperature below 0℃.The catalytic system based on Ni(η^5-Ind)2 complex displaed an extremely high productivity(TOF up to 16900h^-1)and a good regioselectivity to 2,3-dimethylbutenes (2,3-DMB) in dimers(66.4%)under proper reaction parameters.     

Effects of Temperature and Catalyst to Oil Weight Ratio on the Catalytic Conversion of Heavy Oil to Propylene Using ZSM-5 and USY Catalysts

It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC (fluid catalytic cracking). The effects of temperature and C/O ratio (catalyst to oil weight ratio) on the distribution of the product and the yield of propylene were investigated on a micro reactor unit with two model catalysts, namely ZSM-5/Al2O3 and USY/Al2O3, and Fushun vacuum gas oil (VGO) was used as the feedstock. The conversion of heavy oil over ZSM-5 catalyst can be comparable to that of USY catalyst at high temperature and high C/O ratio. The rate of conversion of heavy oil using the ZSM-5 equilibrium catalyst is lower compared with the USY equilibrium catalyst under the general FCC conditions and this can be attributed to the poor steam ability of the ZSM-5 equilibrium catalyst. The difference in pore topologies of USY and ZSM-5 is the reason why the principal products for the above two catalysts is different, namely gasoline and liquid petroleum gas (LPG), repspectively. So the LPG selectivity, especially the propylene selectivity, may decline if USY is added into the FCC catalyst for maximizing the production of propylene. Increasing the C/O ratio is the most economical method for the increase of LPG yield than the increase of the temperature of the two model catalysts, because the loss of light oil is less in the former case. There is an inverse correlation between HTC (hydrogen transfer coefficient) and the yield of propylene, and restricting the hydrogen transfer reaction is the more important measure in increasing the yield of propylene of the ZSM-5 catalyst. The ethylene yield of ZSM-5/Al2O3 is higher, but the gaseous side products with low value are not enhanced when ZSM-5 catalyst is used. Moreover, for LPG and the end products, dry gas and coke, their ranges of reaction conditions to which their yields are dependent are different, and that of end products is more severe than that of LPG. So it is clear that maximizing LPG and propylene and restricting dry gas and coke can be both achieved via increasing the severity of reaction conditions among the range of reaction conditions which LPG yield is sensitive to.     

茂－茚锆金属络合物催化乙烯/1－己烯共聚和丙稀均聚研究

Complexes （R^1Cp）（R^2Ind）ZrCl2, the catalysts previously reported active for ethylene polymerization showed high activity in ethylene/1-hexene copolymerization and propylene polymerization in the presence of MAO. The content of 1-hexene in copolymers ranged from 1.2% to 3.2%. In propylene polymerization the complex 1 showed the highest activity, up to 1.2×10^6 g of polypropylene per mol of catalyst per hour. Based on the analysis of NMR spectral data, the relationships between complex structures and polymerization results were explored.     

Relationship between the reducibility and selectivity of CeMoxV1-xO4 catalysts by kinetic parameters of TPR

CeVO4, CeMo0.01V0.99O4 and CeMo0.03V0.97O4 were prepared by co-precipitation method. The addition of molybdenum as promoter shows a positive effect on the catalytic behavior of CeVO4 in oxidative dehydrogenation of propane to propylene. The reduction behaviors of the catalysts were characterized by temperature-programmed reduction. The activation energies of reduction process for the catalysts were obtained at different reduction rates by Kissinger method. The addition of Mo to CeVO4 enhances the selectivity to propylene.     

SIMULATION OF EFFECTS OF REACTIVE IMPURITIES ON PROPYLENE POLYMERIZATION IN LOOP REACTORS THROUGH GENERATION FUNCTION TECHNIQUE

The estimation of the amount of reactive impurities in a loop reactor is of strategic importance to the propylene polymerization industry. It is essential to investigate the level of impurities in order to develop reliable monitoring and control strategies. This paper described one approach based on generation function technique with the following two steps. First, a new mechanism for propylene polymerization was proposed by considering the effects of the reactive impurities in the material on the propylene polymerization. Second, a series of equations of population balance for the propylene polymerization in loop reactors were established based on the proposed mechanism. Accordingly, the equations were transformed into the mathematic matrix through the generation function technique to investigate the effects of the reactive impurities on the propylene polymerization. Significant effects of the reactive impurities were analyzed through computational simulation. The results show that the concentration of active centre on catalysts and the polymerization conversion both decrease with the increase of the initial concentration of any reactive impurity; hydrogen concentration decreases with the increase of the initial concentration of ethylene or butylenes, whereas, it increases with the increase of the initial concentration of propadiene; the simulated weight average molecular weight and the molecular weight distribution index of polymer resins both increase with the increase of the initial concentration of ethylene or butylenes. They decrease with the increase of the initial concentration of propadiene.     

Synthesis of propylene carbonate from urea and 1,2-propanediol

The production of propylene carbonate(PC)from urea and 1,2-propanediol(PG)was investigated in a batch process.The catalytic performances of zinc chloride and magnesium chloride were investigated for this reaction system.The influences of various operation conditions on the PC yield were explored.In this work,MgCl_2 and ZnCl_2 showed the excellent catalytic activity toward PC synthesis,and the yields of propylene carbonate reached 96.5%and 92.4%,respectively.The optimum reaction conditions were as follows...     

SYNTHESIS AND PROPERTIES OF A NOVEL COMPOSITE ZSM-5 ZEOLITE/VERMICULITE CATALYST

The composite ZSM—5 zeolite/vermiculite catalyst,in which tiny ZSM—5 zeolite parti-cles embedded in the vermiculite substrate,has been synthesized by hydrothermal method with vermiculite assilicon source.The catalytic behavior of resulting catalyst for xylene isomerization,propylene aromatizationand toluene disproportionation is better than that of HZSM—5 zeolite.     

RING OPENING POLYMERIZATION OF PROPYLENE SULFIDE BY RARE EARTH COORDINATION CATALYSTS*

Ring opening polymerization of propylene sulfide using rare earth coordination catalysts has been investigated for the first time. It has been found that trinary rare earth coordination catslysts composed of rare earth compounds of phosphonate, naphthenate or acetylacetonate, trialkyl sluminum and water are effective catalysts for the polymerization of propylene sulfide. The polymerization in toluene is a homogeneous reaction. High molecular weight as high as several million poly(propylene sulfide) with high yield can be prepared by these catalysts. Kinetic studies showed that the polymerization rate is of first order with respect to both monomer concentration and catalyst concentration. The activation energy of the polymerization reaction is 61.4 k fJ/mol. The structure of the polymers so obtained has also been characterized by ~(13)C NMR spectroscopy, X-ray diffraction, gel permeation chromatography and differential scanning calorimetry.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.