CuSAPO-5分子筛的合成、表征及对甲苯吸附性能

采用水热合成法,以三乙烯四胺（TETA）为模板剂,合成CuSAPO-5分子筛。通过扫描电子显微镜（SEM）、粉末X射线衍射（XRD）、傅里叶变换红外光谱（FT-IR）、热重（TG）、N₂吸附及元素分析等手段对分子筛样品进行表征,考察了不同硅铝比对合成分子筛晶体的影响,并测定了分子筛样品对甲苯的吸附性能。结果表明,将合成液的pH值调节为4.8～5.0,于150～170℃晶化1 d,可合成晶体形貌为球体的CuSAPO-5分子筛,粒径约为30 μm。分子筛样品具有较好的热稳定性,仍保持了SAPO-5分子筛的AFI骨架结构,属于微孔分子筛,孔径约为0.70nm,比表面积约为265 m²·g^-1。元素分析结果表明分子筛中P、Si、Al和Cu的含量分别为12.56%、4.48%、7.17%和6.25%。样品对甲苯的吸附约在120 min时达到饱和,吸附量约为180 mg·g^-1。     

微波辐射法合成SAPO-5分子筛中硅铝比对产物结晶度和甲苯吸附性能的影响

采用硅溶胶作硅源, 用微波辐射法在酸性条件下(pH=4.5-5.0)合成了SAPO-5分子筛, 利用X射线衍射(XRD), 傅立叶变换红外光谱(FT-IR), 扫描电镜(SEM)和Brunauer-Emmett-Teller (BET)比表面积分析对样品的结晶度、形貌和比表面等进行表征, 考察了晶化原料硅铝比对分子筛结晶度和晶体颗粒长径比(c/a)的影响, 测定了分子筛对甲苯的吸附性能. 结果显示, 采用微波辐射法合成的SAPO-5分子筛, 在硅铝摩尔比为0.50附近生成产物的结晶度最好, 晶体颗粒的长径比最小(约为1.0). 尽管不同硅铝比条件下得到的样品比表面测定结果变化不大, 但对甲苯的吸附实验显示, 在硅铝比为0.50时样品的吸附速率和饱和吸附量均达到了最大值. 这与表征所得的结晶度和长径比的变化一致, 即结晶度好,长径比小的SAPO-5分子筛具有更好的甲苯吸附性能.     

CoSAPO-34分子筛的合成、表征及其光催化脱氮性能

利用水热合成法,以三乙烯四胺(TETA)为模板剂,正硅酸乙酯、磷酸、氢氧化铝及乙酸钴为原料,合成了CoSAPO-34分子筛。通过扫描电子显微镜(SEM)、粉末X射线衍射(XRD)、热重(TG)、N2吸附-脱附和紫外-可见漫反射光谱(UV-Vis DRS)等方法对合成的分子筛进行表征。以吡啶-正辛烷体系为模拟油品对分子筛催化剂的脱氮效果进行评价,考察了样品的用量、光催化时间及循环催化次数对其脱氮性能的影响。结果表明:当合成原料的物质的量之比为n_(P_2O_5)∶n_(Al_2O_3)∶n_(SiO_2)∶n_(Co)∶n_(TETA)=1∶0.82∶0.26∶0.81∶2.05,在200℃晶化24 h,合成得到粒径约为50μm、仍保持了SAPO-34分子筛的骨架结构、形貌为立方体的Co SAPO-34分子筛,而且该分子筛具有较好的热稳定性。在500 W氙灯光照条件下反应150 min,样品对质量分数为100μg·g-1模拟油品的脱除率达到70%,循环3次光催化脱氮活性基本保持不变。     

SAPO-5分子筛的可控合成及晶化过程探索

在非醋酸体系下分别通过动态和静态水热晶化方法合成了SAPO-5分子筛, 并考察了转速、 晶化时间及凝胶体系水硅比对SAPO-5分子筛晶相及形貌的影响, 采用X射线衍射(XRD)和扫描电子显微镜(SEM)技术研究了静态、 动态水热条件下SAPO-5分子筛的晶化过程. 结果表明, 静态水热条件下晶化6 h得到的SAPO-5分子筛为球状、 六边形柱状聚集晶体; 而在20 r/min转速下晶化2和6 h得到的SAPO-5分子筛分别为分散的凹面柱状晶体(凹面直径约6~8 μm)及均一分散的球状晶体(直径为16 μm); 在60 r/min转速下晶化3 h即可得到高度分散的六边形柱状晶体(六边形直径约5~8 μm); 提高转速至100和140 r/min时仅需晶化1 h即可得到六边形柱状晶体. 通过考察体系水硅比(H₂O/Si摩尔比)的影响, 确定最佳的水硅比为70, 此条件下所得晶相为纯相且分子筛的分散度最好. 综上可知, 相较于静态晶化, 动态晶化不仅从形貌上改善了晶体的分散度, 通过缩短晶化时间、 降低晶化转速也提高了SAPO-5分子筛的晶化效率. 本文采用较小的水硅比(H₂O/Si摩尔比为70)、 较低的模板剂用量在非醋酸体系下合成了SAPO-5分子筛, 为SAPO-5分子筛的合成提供了一条更简单、 经济的路线.     

Cu/SBA-1的合成及其对苯羟化反应的催化性能

以正硅酸乙酯(TEOS)为硅源,十六烷基三乙基溴化铵(CTEABr)为模板剂,在强酸性条件下采用溶胶-凝胶法合成了Cu掺杂SBA-1分子筛.用XRD、SEM、N2吸附/脱附、红外光谱对所制备的样品进行表征.XRD测定结果显示所合成的Cu/SBA-1具有明显的立方介孔结构,Cu/SBA-1比表面积达931 m2·g-1,...     

球形TiSAPO-34分子筛的合成、表征及其对亚甲基蓝的吸附性能

利用水热法合成了Ti SAPO-34分子筛,通过扫描电子显微镜(SEM)、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)、N2吸附-脱附、紫外-可见漫反射吸收光谱(UV-Vis DRS)、热重(TG)等方法对其形貌、物相组成、孔径等进行表征。以亚甲基蓝的水溶液模拟污染物评价Ti SAPO-34分子筛吸附性能,考察了钛的掺杂量及样品再生后对亚甲基蓝吸附性能的影响。结果表明:样品形貌为球形,是一种微孔分子筛,具有较好的热稳定性。样品中部分Ti原子成功进入骨架,仍保持了SAPO-34分子筛的骨架结构。在190℃晶化24 h得到的样品吸附性能较好,0.3 g样品吸附1 h对0.01 g·L~(-1)亚甲基蓝的水溶液模拟污染物吸附率达到80%。     

FeZSM-5/N2O体系催化氧化甲苯制甲酚的研究

采用四丙基氢氧化铵为模板剂, 硝酸铁为铁源应用水热合成法制备了一系列FeZSM-5分子筛催化剂, 利用X-射线粉末衍射分析, N2吸附/脱附, 元素分析等技术对催化剂进行了表征. 并进行了所制样品对甲苯催化氧化制甲酚反应催化性能的研究. 本文详细考察了Fe含量、反应物配比、反应温度以及空速等各种因素对甲苯催化氧化制甲酚反应催化性能的影响. 结果表明在400 ℃, 甲苯∶N2O为1∶4, 空速为8 000 mL·h-1·g-1条件下反应结果最佳, 最大甲苯转化率约为12.6%, 甲酚选择性约为33.0%.     

ZIF-8的合成、表征及正己烷吸附性能

以甲醇为溶剂,硝酸锌六水合物为锌源,2-甲基咪唑为有机配体,通过溶剂热法合成了金属有机骨架材料ZIF-8;采用X射线衍射(XRD)、氮气吸附、热重-差热分析(TG-DSC)和扫描电子显微镜(SEM)等方法对ZIF-8样品进行了表征;研究了正己烷在ZIF-8上的液相吸附动力学和动态选择性吸附性能.结果表明,合成的ZIF-8晶体具有方钠石结构,结晶度较高,孔结构主要为0.37~1.10 nm的微孔,BET比表面积为1836 m2/g,孔体积为0.65 cm~3/g.TG-DSC和高温原位XRD分析结果表明,合成的ZIF-8具有良好的热稳定性能.283~313 K时,正己烷在ZIF-8上液相吸附的扩散系数为(2.53~8.88)×10-12cm~2/s,扩散活化能为31.11 k J/mol;308 K时,ZIF-8对正己烷的动态饱和吸附量为187.3 mg/g,由吸附穿透曲线计算得出Thomas速率常数为2.17×10~(-3)m L·min~(-1)·mg~(-1).与5A分子筛相比,ZIF-8对正己烷的吸附容量高出约1倍,液相吸附表观扩散时间常数高出约70%.     

水热法合成球花状二硫化钼及其电化学性能

采用二水钼酸钠(Na_2MoO_4·2H_2O)和硫脲(CS(NH_2)_2)分别作为钼源和硫源,通过水热合成法获得球花状二硫化钼,其较佳的水热条件为:180℃下反应48 h,钼硫原子比为1∶4,反应物浓度为0.001 mol·L-1,在100 m L反应釜中的填充体积为90 m L。采用X射线衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)、对样品的物相和形貌进行了表征,并利用低温氮吸附BET模型测试了样品的比表面积。结果表明,合成的二硫化钼结晶性良好,平均粒径约为1μm,比表面积约为87 m2·g-1,分布均匀且无明显团聚。通过循环伏安(CV)曲线、恒电流充放电曲线(GCD)、阻抗谱图(EIS)表征其电化学性能,测试表明:在3 mol·L-1 KOH水相电解液中,单电极比电容可达130.6 F·g-1(扫速为5 m V·s-1)和110.9 F·g-1(电流密度为0.1 A·g-1),界面转移电阻Rct为0.33Ω;循环1 000圈后比电容损失为14.7%。说明采用该水热法合成的二硫化钼可以成为超级电容器电极的理想材料。     

Cu改性SAPO-11分子筛催化萘和甲醇甲基化反应的研究

分别采用水热合成法和浸渍法对SAPO-11分子筛进行Cu改性.通过X射线衍射(XRD)、扫描电镜(SEM)、NH_3-程序升温脱附(NH_3-TPD)、H_2-程序升温还原(H_2-TPR)、~(29)Si固体核磁共振(~(29)SiMAS NMR)以及N_2吸附-脱附(N_2adsorption-desorption)等表征手段对改性前后SAPO-11分子筛的结构、酸性进行表征,并研究了改性后分子筛催化合成2,6-二甲基萘反应性能的影响规律.结果表明,经水热合成法进行Cu改性的SAPO-11分子筛结晶度升高,酸中心数量增加,比表面积和孔体积上升,从而使萘的转化率、2,6-二甲基萘的选择性、2,6-二甲基萘与2,7-二甲基萘的比值及2,6-二甲基萘的收率提高.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.