ZIF-8吸附剂上CH4/N2的吸附分离性能与热力学性质

将沸石咪唑酯骨架结构材料应用于抽放煤层甲烷的浓缩净化研究。以三乙胺(TEA)为导向剂,ZnSO₄为金属离子源,水为溶剂,采用水热合成法进行了ZIF-8吸附剂的制备。采用XRD、物理吸附、动态吸附分离和反相气相色谱(IGC)等方法对ZIF-8的物理结构、化学稳定性、吸附分离性能和热力学性质进行了研究。结果表明,ZIF-8具有良好的化学稳定性,能够在强酸、强碱和强极性的溶剂中保持结构的稳定性;在298 K时,ZIF-8对CH₄/N₂的分离因子达到3.4,与活性炭相当,但CH₄、N₂在ZIF-8上的吸附热比在活性炭上低20%左右。     

不同尺寸ZIF-8对U(VI)的吸附性能

以经典的金属有机骨架(MOFs)材料ZIF-8为吸附剂,研究尺寸效应对铀吸附性能的影响。 通过3种方法合成不同粒径的ZIF-8,利用扫描电子显微镜(SEM)、X射线粉末衍射仪(XRD)、表面积与孔隙度分析仪等对其进行了表征,测试了相同条件下不同尺寸的ZIF-8对硝酸铀酰溶液中U(VI)吸附,分别对其吸附过程的动力学和吸附等温线进行了考察,并测试了材料的可重复利用性。 结果表明,成功制备了高结晶性、高纯度的ZIF-8,产物形貌呈菱形十二面体,颗粒均匀,粒径分别为约50 nm、150 nm及2 μm;3种ZIF-8具有单一均匀的微孔结构和与粒径高度相关的比表面积;不同尺寸的ZIF-8均能快速吸附溶液中的U(VI),在室温pH=3下,在70 min左右时即可吸附初始质量浓度为200 mg/L的U(VI)溶液中90%以上U(VI);其中较小尺寸(约50 nm)的ZIF-8吸附性能最好,单位质量ZIF-8吸附U(VI)的饱和吸附量达到520.26 mg/g;ZIF-8对U的吸附动力学上符合二级动力学方程,吸附等温线符合Langmuir模型,说明ZIF-8对U(VI)的捕获属于化学单层吸附;经过4个吸附-解吸循环后,3种尺寸的ZIF-8均依然保持了70%以上的去除率。     

ZIF-8/改性聚丙烯腈电纺纳米纤维的制备及其高效去除水中孔雀石绿

通过原位生长方法,将最常见的金属有机骨架(MOFs)——沸石咪唑酯骨架材料(ZIF-8)固定到羧甲基化聚丙烯腈静电纺丝纳米纤维(PAN-COOH NFs)表面,得到ZIF-8/PAN-COOH NFs。通过扫描电子显微镜(SEM)、能量色散光谱(EDS)、X射线粉末衍射(XRD)和傅里叶变换红外光谱(FTIR)对合成的ZIF-8/PAN-COOH NFs形貌和结构进行表征,并深入研究ZIF-8/PAN-COOHNFs从废水中去除孔雀石绿(MG)的性能。研究发现： ZIF-8/PAN-COOH NFs对MG的吸附符合拟二级动力学方程,吸附过程可采用Langmuir等温线模型拟合,其对MG的最大吸附容量可达3 604 mg·g^-1。此外,ZIF-8/PAN-COOH NFs在染料吸附实验中表现出良好的分离功能和重复利用性。     

低共熔溶剂中原位合成ZIF-8膜及其气体分离性能

在α-氧化铝载体上,采用原位合成法,在尿素/氯化胆碱低共熔溶剂中合成了ZIF-8膜。采用X射线衍射(XRD)和扫描电子显微镜(SEM)对合成的ZIF-8膜进行了表征。考察了反应溶液浓度、降温速率对ZIF-8膜合成的影响。通过优化合成条件合成了表面平整致密,厚度为8 μm的ZIF-8膜。采用Wicke-Kallenbach技术对优化条件下合成的ZIF-8膜进行了单组分气体渗透和双组分混合气体分离性能表征。在室温(293 K)下,ZIF-8膜对H2/CO2、H2/O2、H2/N2、H2/CH4双组分气体的分离系数分别为7.4、5.2、9.1、13.8,均大于相应的努森扩散分离系数,说明合成的ZIF-8膜具有分子筛分性能。     

ZIF-8的制备及其作为杀菌药物载体的研究

采用室温搅拌法制备了金属有机骨架材料ZIF-8.通过X射线粉末衍射(XRD)、红外光谱(IR)、N2吸附-脱附、透射电子显微镜(TEM)和扫描电子显微镜(SEM)对所得样品进行了表征分析,并以苯扎氯铵为杀菌药物模型,研究了ZIF-8对苯扎氯铵这种药物的载药及体外释药性能.表征结果显示,制备的ZIF-8是一种具有规则十二面体方钠石结构的晶体,BET比表面积为2 643m2/g.载药及体外释放实验表明,ZIF-8对浓度为4mmol/L苯扎氯铵的载药量为43g/100g ZIF-8,载药后的ZIF-8在释放90h后,释放率达84.82%,说明ZIF-8对苯扎氯铵有较好的缓释性能.     

两种新型多孔金属-有机凝胶的合成、表征与气体吸附性能

以1,4-二(3-乙酰丙酮基)苯(DAB)为有机配体分别与铝离子和铬离子反应,合成出2个新型的金属-有机凝胶:Al-湿凝胶和Cr-湿凝胶,通过直接干燥法得到相应的2种多孔干凝胶:Al-干凝胶和Cr-干凝胶.通过X射线粉末衍射仪(PXRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)、热重分析仪(TGA)、X射线能谱仪(EDS)和氮气吸附-脱附仪对凝胶材料的结构和形貌进行了表征.结果显示,2种多孔金属有机凝胶材料是由球状纳米粒子堆积而成,具有较高的比表面积、丰富的微孔及少量的介孔结构.气体吸附性能测试结果表明,Al-干凝胶的比表面积为790.3 m2/g,在1.01×105Pa,77 K下能够吸附117.45 cm3/g的氢气,在273 K下能够吸附60.74 cm3/g的二氧化碳.     

金属有机骨架材料ZIF-8富集黄芩中黄芩苷的新方法

本工作旨在探索MOFs材料高效富集黄芩中黄芩苷的新方法,拓展MOFs在吸附领域的用途.溶剂热法合成了沸石咪唑酯骨架-8（ZIF-8）,并进行了结构表征,以确保其准确合成.研究了ZIF-8对黄芩苷的吸附规律和作用机理：ZIF-8对黄芩苷的吸附符合准二级动力学方程,平衡吸附数据符合Langmuir吸附等温模型.采用响应面法（RSM）得到优化后的最佳吸附参数,在此条件下,ZIF-8对黄芩中黄芩苷的吸附率高达98.22%,且对黄芩中其它成分吸附效果不显著,以pH 6.8的PBS溶液作解吸液,ZIF-8对黄芩苷的解吸率为62.46%,而黄芩苷的纯度由吸附前的21.55%提高到解吸后的64.27%,且ZIF-8在吸附前后稳定性良好,回收率达到83.50%.因此,ZIF-8在吸附纯化黄芩苷方面具有潜在的应用价值.     

介孔SiO_2包覆Ag/ZIF-8核壳型催化材料的合成

通过液相自组装制备了Ag/ZIF-8;进一步以十六烷基三甲基溴化铵(CTAB)为结构导向剂,在疏水Ag/ZIF-8颗粒表面包覆一层介孔二氧化硅(MS)壳,合成了具有核壳结构的Ag/ZIF-8@MS催化剂,并对其进行了结构和性能表征.结果表明,Ag/ZIF-8@MS具有均一的颗粒尺寸(Ag/ZIF-8@MS粒径约为100 nm,Ag粒径约为15 nm)、较高的比表面积(539 m~2/g)及较大的孔体积(0.64 m~3/g);透射电子显微镜表征结果表明,介孔二氧化硅表层厚度约为20 nm.于550℃煅烧后,催化剂结构转变成Ag/Zn O@MS核壳结构.以催化对硝基苯酚生成对氨基苯酚为模型反应,对2种结构的Ag催化剂的催化性能进行了测试.催化反应结果表明,核壳型结构Ag/ZIF-8@MS材料催化对硝基苯酚反应的转化率超过95%,证明了这种以ZIF-8为载体的核壳型材料的优势.     

聚(N-甲基-N-对乙烯基苄基乙酰胺)对水中苯酚的吸附

由大孔交联氯甲基化聚苯乙烯进行甲胺化和乙酰化反应,合成了聚(N-甲基-N-对乙烯基苄基乙酰胺)树脂,树脂的氯含量由原来的3.95mmol/g降至0.63mmol/g.测定了树脂对水中苯酚的吸附等温线,结果表明,吸附平衡数据符合Freundlich等温方程.利用热力学函数关系计算了吸附焓、吸附自由能和吸附熵,结果表明,吸附量在10～40mg/g时,吸附焓为-71.20～-24.65kJ/mol,吸附自由能为-4.64～-6.07kJ/mol,吸附熵为-62.35～-218.56J/(mol·K).讨论了吸附过程中树脂对水中苯酚吸附的氢键与疏水作用的吸附机理.     

甲氧基修饰的大孔交联树脂对苯酚的吸附机理

由大孔氯甲基化聚苯乙烯合成了含有悬挂醚键的甲氧基修饰的大孔交联树脂.通过化学分析(氯含量的测定)、红外光谱和元素分析等手段,确证甲氧基负载在聚苯乙烯骨架上,负载量为4.10mmol/g.测定了这种树脂对正己烷中苯酚的吸附等温线,表明其对正己烷中苯酚的吸附是放热的,随着温度的升高,吸附量逐渐降低,且吸附等温线可拟合成直线.通过吸附焓的计算、不同条件下吸附等温线的比较以及理论计算等方法,确证氢键是甲氧基修饰的大孔交联树脂吸附正己烷中苯酚的主要驱动力,树脂骨架上负载的醚氧原子与苯酚的酚羟基氢原子形成了强烈氢键.     

5A沸石在水溶液中对氯化十四烷基吡啶的吸附

表面活性剂在固液界面上的吸附作用是十分重要的课题,为此我们开展了这方面的研究^[1-3]。沸石结构规则,孔大小均匀,具有特殊的吸附性质。近年来由于作为合成洗涤剂助剂的三聚磷酸钠可使水质富营养化,故国内外都在研究洗涤剂的低磷化措施。     

Adsorption of Zinc and Cyanide from Cyanide Effluents on Anionic Ion-exchange Resin

The adsorption of zinc and cyanide from cyanide effluents onto strong and weak basic anion exchange resins was studied in a batch adsorption system. Factors influencing the adsorption rates such as resin selection, resin amounts, contact time and temperature were studied and scanning electron microscopy-energy disperse spectroscopy(SEM-EDS) was used in the analysis. The present study shows that the adsorption capacity of resin 201×7 is better than that of resin 301. The adsorption process was relatively fast and came to equilibrium after 60 min. The kinetic data were analyzed with three models and the pseudo-second-order kinetic model was found to agree with the experimental data well. The equilibrium data could also be described well by Langmuir isotherm model. Thermodynamic parameters such as enthalpy change(ΔH⁰), free energy change(ΔG⁰) and entropy change(ΔS⁰) were calculated and the adsorption process was spontaneous and endothermic.     

气体超临界吸附研究进展

综述了近年来国内外学者对超临界气体在固体表面吸附的研究情况。指出了气体在临界温度以上吸附与临界温度以下吸附的不同之处;对现行的关于超临界气体的吸附理论研究进行了讨论,并在此基础上提出了研究中存在的总是及进一步的研究方向。     

Adsorption properties and mechanism of sepiolite to graphene oxide in aqueous solution

Graphene oxide (GO) is widely used in various fields such as improving the performance of cement-based materials and making composite materials due to its large specific surface area and abundant oxygen-containing functional groups. However, it has also caused water pollution. To remove GO in aqueous solution, sepiolite (SEP) was used to adsorb it. The effects of pH, adsorbent quality, GO concentration, temperature and adsorption time on the ability of SEP to adsorb GO were investigated. The materials were characterized by SAP and laser particle size analyzer, and the adsorption performance and mechanism of SEP for GO were further analyzed by XRD, FTIR, SEM, TEM, XPS, AFM, and Zeta potential microscopic tests. The results showed that: 1) Under the conditions of temperature 303 K, pH = 3, adsorbent mass 30 mg, and initial concentration of GO 100 mg/L, the adsorption effect was the best, and the adsorption rate reached 94.8 %. 2) The adsorption reached equilibrium at 2160 min, and the adsorption process was more in line with the pseudo-second-order adsorption kinetic equation, and the adsorption behavior was controlled by chemical effects. 3) The adsorption of SEP to GO is more consistent with the Langmuir and Temkin adsorption isotherm model, and the reaction is a spontaneous, endothermic, and entropy-increasing process. Experiments showed that SEP had a strong adsorption capacity for GO, which provides a reference for the treatment of toxic GO in aqueous solution and the realization of water ecological protection.     

Removal of Thiram from Aqueous Solutions

In this study activated carbon was used for the removal of thiram from aqueous solutions. Adsorption experiments were carried out as a function of time, initial thiram concentration and temperature. Equilibrium data fitted well to the Freundlich and Langmuir equilibrium models in the studied concentration range. Adsorption kinetics followed a pseudo second‐order kinetic model rather than pseudo first‐order model. The results from kinetic experiments were used to describe the adsorption mechanism. Both boundary layer and intraparticle diffusion played important role in the adsorption mechanism of thiram. Thermodynamic parameters (ΔG₀, ΔH₀, and ΔS₀) were determined and the adsorption process was found to be an endothermic one. The negative values of ΔG⁰ at different temperatures were indicative of the spontaneity of the adsorption process.     

磷酸铝吸附除水中氟的研究

采用静态吸附法研究了比表面为308m2/g的无定形磷酸铝吸附除氟性能,研究了接触时间、pH值、吸附剂量等对吸附的影响。结果表明,磷酸铝吸附除氟高效、迅速,30min内可以接近最大吸附量。对含氟50mg/g的溶液,优化条件下的最大除氟率约93%。研究了吸附与溶液pH的关系,得到了优化pH值并解释了吸附机理。吸附的最佳pH值约为5.5。用拟二级动力学方程描述了吸附速率并计算了速率常数。用Langmuir方程拟合了吸附等温线,计算的饱和吸附量为53.5mg/g。吸附剂量对分配系数的影响表明吸附剂表面是不均匀的。     

Characterization of two single-wall carbon nanotubes samples by Ar and Kr adsorption isotherms

We investigated by Ar and Kr adsorption isotherm techniques for two kinds of carbon single-wall nanotube bundles prepared by different synthesis methods. Despite the difference in the adsorption capacity in the two samples, the adsorption mechanisms are similar, which indicates that the same adsorption sites are involved for Ar and Kr. We have already measured a similar difference in the adsorbed amount in these samples studied by a low-temperature heat-capacity technique, i.e., for the case of ⁴He as adsorbate. These results cannot be easily explained by only taking into account the topology of the bundles if all tubes are closed-ended. A larger spread of effective surface areas among different sources of samples is reported in the literature data.     

An isotherm equation for adsorption from binary liquid mixtures on solids involving surface heterogeneity and differences in molecular sizes of components and its numerical verification

An equation derived previously¹⁴ for adsorption from binary liquid mixtures composed of molecules of different sizes on heterogeneous solids has been reexamined. Verification of this equation by means of numerical simulation showed its applicability for describing the liquid adsorption onto weakly and strongly heterogeneous surfaces.

---

Eine Isothermen-Gleichung für die Adsorption aus binären flüssigen Gemischen an heterogenen Oberflächen fester Körper unter Berücksichtigung der Differenzen in den Molekülgröen der Komponenten und ihre numerische Verifikation

Zusammenfassung Es wurde die früher¹⁴ abgeleitete Isothermen-Gleichung der Adsorption aus binären flüssigen Gemischen an heterogenen Oberflächen fester Körper abermals untersucht. Durch Computersimulation wurde gezeigt, daß diese Gleichung den obengenannten Prozeß, der sich sowohl an schwach wie auch an stark heterogenen Oberflächen vollzieht, gut beschreibt.

     

可再生甲壳质吸附有机酸的特性研究(Ⅰ)

本文研究可再生甲壳质自水中吸附有机酸的特性，讨论了可再生甲壳质所含活性基团和吸附环境的温度对吸附有机酸的影响。实验结果表明，可再生甲壳质的吸附活性中心是自由胺基；可再生甲壳质吸附草酸的过程是放热变化，升温不利吸附，吸附邻苯二甲酸的过程是吸热变化，升温有利吸附。这一规律，为设计最佳工艺流程提供了有价值的数据。