首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 208 毫秒
1.
建立了消毒剂中三氯新的毛细管电泳分析方法。探讨了缓冲介质和电泳参数对三氯新测定的影响。以15mmol/LNa2HPO4(pH6.0)-乙腈(V(Na2HPO4)∶V(乙腈)=50∶50)为电泳缓冲液,三氯新在12kV电压下电泳,于254nm检测波长处测定,6min可以完成分析。本方法的检出限为0.04mg/L,线性范围0.04~2.00mg/mL(r=0.997),加标回收率在90.9%~108.2%范围内,测定值的相对标准偏差分别为峰高7.7%,迁移时间5.5%。将本法与高效液相色谱法进行比较,样品测定结果的相对误差小于10%。将所建立的方法已用于消毒剂样品中三氯新的测定。  相似文献   

2.
付华峰  关继禹  曲志爽  包建民 《色谱》2006,24(6):566-569
建立了中空纤维膜液相微萃取-高效液相色谱(HPLC)测定醋酸氯己定痔疮栓中醋酸氯己定含量的方法。将样品用醋酸水溶液萃取5次,配成样品溶液,然后用装有正辛醇的中空纤维膜进行液相微萃取,萃取液用高效液相色谱测定。醋酸氯己定的质量浓度为0.5 ~ 16 mg/L时与其峰面积呈良好的线性关系,加样回收率大于98.0%,相对标准偏差低于4.0%。该方法样品处理简单、快速,灵敏度与不经过液相微萃取的HPLC方法相比提高了约24倍,醋酸氯己定痔疮栓中的其他物质对测定无干扰。  相似文献   

3.
展学强  朱智甲  康经武 《色谱》2011,29(4):362-364
建立了以硝酸钾作为背景电解质测定阿霉素脂质体药物中微量硫酸根离子的毛细管电泳分析法。考察了分离电压、背景电解质、电渗流改性剂浓度、pH值对分离测定的影响。结果表明,当毛细管长度为60 cm(有效长度51.5 cm)、分离电压为~15 kV、缓冲溶液采用20 mmol/L硝酸钾(pH 7.0)、电渗流改性剂采用0.4 mmol/L十六烷基三甲基氯化铵(CTAC)、检测波长为202 nm时,阿霉素脂质体破乳液中硫酸根离子和氯离子在3 min内得到了基线分离,硫酸根离子迁移时间和峰面积的相对标准偏差分别小于0.01%和1.0%,检出限为5 μg/L。用该方法对阿霉素脂质体样品中的微量硫酸根离子进行了分析测定,结果令人满意。  相似文献   

4.
联用阴离子选择性耗尽进样和胶束扫集两种在线富集技术,建立了胶束毛细管电泳方法测定化妆品中醋酸氢化可的松的方法。讨论了SDS浓度、样品基体、进样电压、进水时间和进样时间对富集和分离的影响。优化的实验条件:以120 mmol/L SDS-20 mmol/L NaH2PO4(pH2.2)-10%(体积分数)甲醇为缓冲体系,分离电压-20 kV,进样电压-20 kV,进样时间80 s,进水时间200 s,测量波长250 nm。在该实验条件下,醋酸氢化可的松的富集倍数比普通毛细管电泳法提高了约173倍。方法的线性范围为0.05~5.0 mg/L,检出限为12.6μg/L。该方法用于化妆品中醋酸氢化可的松含量的测定,回收率为98%~105%,相对标准偏差均小于4.0%(n=4)。  相似文献   

5.
毛细管电泳法快速测定淀粉中可乐定   总被引:2,自引:0,他引:2  
提出了毛细管电泳快速测定淀粉中可乐定含量的方法。以pH 2.2的磷酸-25 mmol.L-1磷酸二氢钠缓冲溶液为电解质溶液,分离电压20 kV,于214 nm波长处进行紫外检测。在优化的试验条件下,可乐定的质量浓度在0.3~200 mg.L-1范围内与其对应的校正峰面积呈线性关系。检出限(3S/N)为0.1 mg.L-1,测定下限(10S/N)为0.3 mg.L-1。采用该方法对淀粉样品中可乐定含量进行测定,所得加标回收率在97.1%~98.4%之间,相对标准偏差(n=5)小于2.0%。  相似文献   

6.
采用高效毛细管电泳法测定人尿中姜黄素的含量,建立了一种测定体液中姜黄素的简便的分析方法。所用缓冲溶液为15 mmol/L的硼砂溶液(pH 9.24),运行电压为20 kV,检测波长262 nm。姜黄素的峰面积与其质量浓度的线性关系良好,其线性范围为10~300 mg/L,健康人尿中姜黄素的4个浓度水平的添加回收率均大于96.3%,相对标准偏差(RSD)小于2.3%。该法灵敏、快速、准确,可用于体液中姜黄素的批量检测。  相似文献   

7.
采用动态pH联接-扫集毛细管电泳法对化妆品中的迷迭香酸进行检测。用重力进样的方式,进样高度为15 cm的情况下,研究了硼砂浓度、pH、十二烷基硫酸钠(SDS)浓度、甲醇浓度、样品基体、进样时间、分离电压对富集与分离的影响。优化后的实验条件:15 mmol/L硼砂-45 mmol/L SDS(pH8.8)-15%甲醇为缓冲液,进样时间60s,分离电压16kV,样品中磷酸盐浓度10 mmol/L,样品基质pH 4.7。在上述条件下,迷迭香酸(RA)的线性回归方程式为y=539200ρ+53588(r=0.9985),线性范围为0.144~3.6μg/mL,检出限0.036μg/mL,迷迭香酸的回收率为92.5%~103%,相对标准偏差为2.5%。  相似文献   

8.
毛细管区带电泳法快速测定消毒剂中苯扎溴铵的含量   总被引:4,自引:0,他引:4  
丁晓静  赵榕  赵珊  康君行 《色谱》2003,21(5):520-523
采用毛细管区带电泳法(CZE)测定了复方消毒剂中苯扎溴铵的含量。以乙腈-50 mmol/L磷酸二氢钠(pH 2.24)(体积比为50∶50)为背景电解质,以46.4 cm×75 μm i.d.未涂敷的毛细管为色谱分离柱,于214 nm波长检测。详细研究了影响苯扎溴铵准确定量的因素,如缓冲溶液的浓度、pH值、毛细管清洗方式等。样品仅需简单的稀释即可直接进样。采用峰面积外标法定量。方法的检出限为0.2 mg/L(S/N=3),线性范围为20-400 mg/L,苯扎溴铵峰迁移时间的相对标准偏差(RSD)为0.6  相似文献   

9.
建立了叶下珠药材中黄酮的毛细管电泳指纹图谱。以硼砂和十二烷基磺酸钠(pH9.0)为背景电解质溶液,运行电压15kV,紫外检测波长245nm,流体静压力进样15s(高度12cm),对不同产地叶下珠药材进样检测。按电泳峰共有率fi≥70%为依据,确定10个不同产地叶下珠药材中黄酮的毛细管电泳指纹峰为8个,各产地叶下珠的毛细管电泳指纹图谱与标准毛细管电泳指纹图谱的相似度较好。在制备供试液后不同时间进样测定,各指纹峰的相对迁移时间的相对标准偏差小于5%,相对峰面积的相对标准偏差在3.0%~7.8%之间,结果表明样品在48h内稳定。  相似文献   

10.
Guan J  Wang H  Ren L  Niu Q 《色谱》2012,30(1):107-110
建立了同时测定乙醛酸和草酸的毛细管区带电泳法。考察了缓冲溶液的种类、浓度和pH以及分离电压等因素对分离结果的影响。在缓冲溶液为20 mmol/L硼砂-5.5 mmol/L邻苯二甲酸氢钾(pH 9.0)、分离电压20 kV、检测波长212 nm的优化条件下,11 min内即可实现对目标物的分离。乙醛酸和草酸分别在0.8~20 g/L和1.2~20 g/L范围内线性关系良好,相关系数分别为0.9993和0.9975;方法的检出限分别为0.2和0.4 g/L(信噪比为3);样品的加标回收率为98.3%~102.5%,相对标准偏差为0.35%~0.61%。该方法操作简便、快速、成本低廉,已应用于实际样品的分析,并获得了令人满意的结果。  相似文献   

11.
宋宝花  丁晓静  李佳  王志 《色谱》2012,30(9):943-950
建立了复方化学消毒剂中常用有效成分醋酸洗必泰和苯扎氯铵(C12-BAC、C14-BAC及C16-BAC)同时分离测定的毛细管电泳(CE)方法。以37 cm×50 μm未涂层熔融石英毛细管为分离柱,以150 mmol/L磷酸二氢钠-62.5 mmol/L磷酸(pH 2.5)缓冲液(含体积分数为40%的乙腈)为分离缓冲溶液,50 mmol/L醋酸-乙腈(体积比为1:1)为样品介质,检测波长为214 nm。方法的日内及日间精密度分别小于3.0%及3.7%。醋酸洗必泰、C12-BAC、C14-BAC及C16-BAC的检出限(信噪比为3)分别为0.3、0.5、0.5、0.5 mg/L,定量限(信噪比为10)分别为1.0、1.5、1.5和1.5 mg/L,在1.0~400、1.5~200、1.5~200和1.5~200 mg/L范围内,4种有效成分的校正峰面积与相应质量浓度均具有良好的线性关系,相关系数分别为0.9995、0.9998、0.9997和0.9998。加标回收率为93.83%~104.97%。将该法用于实际样品分析,并与液相色谱的分析结果进行比对,获得满意结果。  相似文献   

12.
The paper describes the enhanced separation of o-, m-, p-dihydroxybenzene by capillary electrochromatography (CEC) using gold nanoparticles (AuNPs) as stationary phase. The effect of the AuNPs concentration upon separation was investigated. The experimental parameters, including separation voltage, pH, and concentration of running buffer, were optimized. Under the optimum conditions, a good resolution of three dihydroxybenzene isomers was obtained within 15 min in a 50 cm effective length capillary modified with 0.02 nmol/L AuNPs at a separation voltage of 16 kV in a 50 mmol/L acetate buffer (pH 5.0). The linear ranges were from 10(-6) to 10(-4) mol/L and the detection limits were as low as 10(-7) mol/L. This method was successfully used to analysis two kinds of hair coloring agent sample with recoveries in the range of 90-105% and relative standard deviations (RSD) less than 5.0%.  相似文献   

13.
A novel capillary electrophoresis (CE) method with contactless conductivity detection suitable for the determination of glucosamine (GlAm) and K(+) in pharmaceuticals was devised. Under the optimum conditions (aqueous 30 mM acetate buffer of pH 5.2 as the background electrolyte; voltage 30 kV; 25 degrees C), GlAm (migrating as glucosaminium cation) was well separated from K(+) that could occur in the dosage forms as excipient. The CE analysis was performed in fused-silica capillaries (50 microm i.d., 75 cm total length, 27 cm to detector) and the separation took <3 min. The calibration graphs were linear for both GlAm (100-300 microg/mL; r(2)=0.997) and K(+) (15-75 microg/mL; r(2)=0.997) when using ethanolamine (100 microg/mL) as the internal standard. The LOD values (S/N=3) were 9.3 microg/mL for GlAm and 2.9 microg/mL for K(+). The method was applied to the assay of GlAm content in various dosage forms. Intermediate precision evaluated by determining the content of GlAm in a single formulation on 3 consecutive days was characterized by RSD 2.35% (n=15). Acceptable accuracy of the CE method was confirmed by the added/found GlAm recovery experiments (recoveries 94.6-103.3%) and by statistical comparison of the results attained by the proposed CE and a reference HPLC method.  相似文献   

14.
Microchip capillary electrophoresis in mixed hydro-organic solvent combined with laser-induced fluorescence detection was developed for the separation and detection of physcion and rhein in rhubarb. In contrast to the conventional capillary electrophoresis method, ammonium acetate-dimethyl sulfoxide was used as the basic buffer system in this method. The effects of background buffer, buffer apparent pH*, buffer concentration, water ratio, sample preparation method, and separation voltage on separation and detection were investigated. Optimized separation and detection conditions were obtained: the buffer consisted of 20 mmol/L of ammonium acetate in hydro-organic solvent composed dimethyl sulfoxide, formamide, and water mixed at 60/20/20 (v/v/v) ratio. The separation voltage was 1.9 kV. Under these conditions, the physcion, rhein, and other components of rhubarb can be completely separated within 150 s. Under the methodological verification, good linearity (R ≥ 0.9995) for physcion and rhein, and low limits of detection (0.085 μg·mL−1 and 0.077 μg·mL−1, respectively), satisfactory peak area precisions, migration time precisions (1.74%–3.09%), and accuracy (recovery rate 97.8% and 101.4%) were achieved. It is shown that the proposed method is simple, efficient, fast, sensitive, simple instrument, consumes few samples, has low operating cost, and is linear.  相似文献   

15.
Ma H  Hua Y  Tu C  Yuan L  Wei P 《色谱》2012,30(3):304-308
以对甲氧基苯胺为衍生试剂,采用毛细管电泳法分析了藏红花植物细胞多糖中的单糖组成。对衍生条件进行了优化,并对毛细管分离条件进行了系统的研究。衍生反应在醋酸含量9.5%(v/v)、80 ℃下反应2 h的衍生产率最大,衍生产物紫外检测波长234 nm。在优化的毛细管电泳分离条件(未涂层熔融石英毛细管柱(60 cm(有效长度50 cm)×50 μm),柱温25 ℃,电压20 kV,使用350 mmol/L硼酸电解液(pH 10.21),压力(3.4475 kPa)进样5 s)下,基线分离了11种结构相近的醛糖(来苏糖、木糖、核糖、葡萄糖、甘露糖、半乳糖、鼠李糖、纤维二糖、麦芽糖、乳糖)、酮糖(果糖)的衍生产物。应用该方法定量检测了藏红花植物细胞多糖水解物中糖的成分,各糖的回收率为94.3%~105.4%,相对标准偏差为3.3%~4.6%。  相似文献   

16.
于冰  丛海林  刘虎威  李元宗  刘锋 《色谱》2005,23(5):487-491
采用毛细管电泳技术研究了重组促红细胞生长素(rhEPO)的分离问题。用N,N-二甲基六烷基溴化铵(6,6-ionene)涂层的毛细管测定了rhEPO中唾液酸的微多相性,同时采用毛细管电泳-质谱(CE-MS)联用技术在22 min内鉴定了rhEPO 20段胰酶消化肽中的11段。该方法简单快捷,重现性好,可用于蛋白质一级结构的测定。  相似文献   

17.
Sun B  Macka M  Haddad PR 《Electrophoresis》2002,23(15):2430-2438
Capillary electrophoresis (CE) with UV detection was used for the determination of arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid, p-aminophenylarsonic acid, 4-hydroxy-3-nitrobenzenearsonic acid, 4-nitrophenylarsonic acid, phenylarsonic acid, and phenylarsine oxide. The electrophoretic mobilities of these anionic species were determined in a 20 mM phosphate buffer in a pH range from 4 to 11, which established pH 10 as the optimum for the separation. The target analytes were then separated in a fused-silica capillary using 20 mM NaHCO(3)-Na(2)CO(3) buffer, pH 10, as electrolyte and detected at 192 nm. Both normal- and reversed electroosmotic flow (EOF) separation modes were investigated and in the latter case, poly(diallydimethylammonium chloride) (PDDAC), was used for dynamic coating of the capillary and to provide a stable and reproducible reversed EOF (relative standard deviation RSD, 0.39%). The influence of electrolyte pH and composition, applied voltage, as well as EOF reversal protocols upon the method performance criteria were investigated. The optimised method provided limits of detection for the target analytes of 1.62, 6.22, 1.45, 1.83, 0.34, 0.40, 0.40, 0.18, and 0.30 mg/L As, respectively. Linearity was obtained in the range of 0.5-40 mg/L As (for aryl compounds) and from 5-100 mg/L As (for the remaining analytes). Reproducibility of peak areas was in the range of 0.8-5.5% RSD. The method was applied to the determination of four aryl arsenic compounds used as additives in animal feed. Analytes were extracted with 40 mM hydrochloric acid - acetonitrile 4:1 v/v, and then cleaned up by passing through a C(18) solid-phase extraction cartridge before analysis by CE with detection at 200 nm. Recoveries for the four analytes were in the range of 78.8-108.3%.  相似文献   

18.
采用毛细管电泳安培法建立了肉苁蓉中松果菊苷含量的检测方法,探讨了缓冲溶液种类、工作电位、分离电压、进样时间等对分离和检测的影响.在15 mmol/L硼砂缓冲溶液(pH 9.5),25 kV电压,0.6 V工作电位的条件下,松果菊苷的质量浓度在0.5~50.0 mg/L范围内与峰面积呈良好线性,相关系数为0.9994,检...  相似文献   

19.
A sheathless and electrodeless nanospray interface has been used to interface a polycarbonate capillary electrophoresis (CE) chip to a mass spectrometer (MS). The chip was made of two flat polycarbonate plates which were bolted together. Channels were imprinted in one of the plates with metal wires, using a hydraulic press. A short tapered capillary connected to the chip was used as the nanospray emitter. The advantage of this electrodeless interface is that it was not necessary to apply a electrospray voltage to the chip or the nanospray emitter. Instead, the CE voltage already applied to the buffer compartment on the chip, to drive the electrophoresis, was used to generate the spray also. A low conductivity buffer of 1.25 mmol/L ammonium acetate in 80% methanol was used to obtain a large electric field across the buffer channel. The performance of the device was evaluated by analyzing a mixture of three beta-agonists Relative standard deviation (RSD) values obtained were between 4.8 and 5.0%. A sample concentration of 40 nmol/L resulted in a signal-to-noise ratio of 2 to 5 for the different components. Compared to a conventional CE analysis in a fused silica capillary with UV detection, only a minor loss of resolution was observed, which can be attributed to the design of the chip.  相似文献   

20.
基于稀土Eu(Ⅲ)掺杂的类普鲁士蓝膜修饰的铂电极为工作电极,建立了测定羟考酮的毛细管电泳-电致化学发光分析方法。考察了检测电位、运行缓冲溶液的酸度及浓度、分离电压、进样条件等对电泳分离效果及检测灵敏度的影响。在最佳的实验条件下,羟考酮可在4 min内得到分离,其ECL强度值与羟考酮的质量浓度在7.0×10-2~7.0μg/mL和7.0~70.0μg/mL范围内呈良好的线性关系,检出限为4.2×10-2μg/mL(3σ),峰高和迁移时间的相对偏差分别为3.6%和0.48%(n=6)。方法用于兔血浆中羟考酮含量的检测,加标回收率在99.7%~101.0%之间。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号