尾式锌卟啉轴向配位反应的光谱性质

采用紫外-可见光谱和荧光光谱滴定方法考察了5-p-(4-溴乙氧基)苯基-10,15,20-三苯基锌卟啉和5-p-(4-烟酸乙氧基)苯基-10,15,20-三苯基锌卟啉与咪唑类客体之间的配位反应性质。热力学实验研究结果表明,2种锌卟啉与咪唑类客体之间的轴配反应是按摩尔比1∶1进行的,轴配反应的平衡常数均按K(2-MeIm)>K(N-MeIm)>K(Im)的顺序依次减弱,其中5-p-(4-烟酸乙氧基)苯基-10,15,20-三苯基锌卟啉与2-甲基咪唑间的轴配反应有更大的平衡常数,为5.46×105L/mol。荧光光谱滴定实验显示,随客体浓度的增加,2种主体与咪唑类客体形成的轴配体系均具有荧光猝灭效应。     

光谱法研究硝基苯基卟啉锌与咪唑类的轴向配位反应

采用紫外-可见光谱滴定法和荧光光谱法,考察了5-对硝基苯基-10,15,20-三苯基锌卟啉和5-邻硝基苯基-10,15,20-三苯基锌卟啉与3种咪唑类客体小分子进行轴向配位反应的光谱性质,并探讨取代基团在不同位置时的锌卟啉及具有不同结构特点的客体对该类轴配反应进行的影响。 实验结果表明,2种锌卟啉与咪唑类客体之间的轴配反应是按摩尔比1∶1进行,轴配反应的平衡常数均按K(2-MeIm)＞K(N-MeIm)＞K(Im)顺序依次减弱,其中5-邻硝基苯基-10,15,20-三苯基锌卟啉与2-甲基咪唑间的轴配反应有最大的平衡常数5.85×10⁵ L/mol。 轴配反应的平衡常数均随温度的升高而降低,温度升高不利于平衡反应的进行。 热力学参数表明,这类反应的驱动力是焓驱动,是自发进行的配位反应。 随客体浓度的增加,5-对硝基苯基-10,15,20-三苯基锌卟啉(荧光峰位：592.9、634.2 nm)与咪唑类客体的轴配体系具有荧光增强的效应,5-邻硝基苯基-10,15,20-三苯基锌卟啉(荧光峰位：583.6、629.8 nm)与咪唑类客体的轴配体系具有荧光猝灭的效应。 轴配体系的荧光效应是由锌卟啉中硝基基团的位置所决定的,而与客体的结构特点无关。     

酪氨酸修饰新型手性卟啉配合物的合成与表征

利用亲核取代反应合成了一种L-酪氨酸修饰的新型手性自由卟啉(5-[2-(L-酪氨酸)乙氧基苯基]-10,15,20-三苯基卟啉)及其对应的金属锌卟啉(5-[2-(L-酪氨酸)乙氧基苯基]-10,15,20-三苯基锌卟啉).通过元素分析、紫外-可见光谱、核磁共振氢谱、圆二色谱、红外光谱、荧光光谱等多种谱图对合成的目标化合物进行了表征.     

新型手性基团修饰的金属卟啉的合成及性质研究

合成了一种手性基团修饰的金属卟啉化合物[5-对(L-亮氨酰氧乙氧基)苯基-10, 15, 20-三苯基卟啉锌]. 通过元素分析、紫外可见光谱、红外光谱、圆二色光谱及核磁共振波谱对该化合物进行了较详细的表征. 同时, 采用分子力学方法搜索了主体的最低能量构象, 从理论上进一步解释实验结果. 利用Z扫描技术测定了该化合物的三阶非线性光学性质.     

不对称酰胺基卟啉及其锌配合物的合成,表征及光谱研究

以CH2Cl2为溶剂,通过5-(4-氨基)苯基-10,15,20-三苯基卟啉(MATPP)与异烟酸直接反应得到一种不对称酰胺基卟啉配体(H2P),并合成了其锌配合物(ZnP),利用紫外-可见光谱、红外光谱、核磁共振氢谱、元素分析等测试方法对化合物的结构加以确认.同时,结合光谱法初步研究了卟啉的自聚合性质.研究表明,紫外-可见光谱显示了卟啉的J-聚合特征,荧光量子产率由于自聚合而降低.     

卟啉化合物研究(Ⅸ)——聚5-邻丙烯酰胺苯基-10,15,20-三苯基卟啉及其钴配合物的合成

将丙烯酰氯和5-邻氨基苯基-10,15,20-三苯基卟啉(Ⅰ)相连合成了5-邻丙烯酰胺苯基-10,15,20-三苯基卟啉(Ⅱ)。在引发剂作用下,Ⅱ进一步聚合,生成聚5-邻丙烯酰胺苯基-10,15,20-三苯基卟啉(Ⅲ),同时还合成了单体和聚合物的钴配合物。通过元素分析、核磁共振谱、红外光谱和可见吸收光谱对单体和聚合物的结构进行了鉴定。     

新型卟啉衍生物的合成、结构表征和电化学性质的研究

以合成的[5-(4-溴苯基)-10,15,20-三苯基卟啉]锌为底物,通Stille偶联的方法合成5-(4’-氨基-4-联苯基)-10,15,20-三苯基卟啉,[5-(4’-氨基-4-联苯基)-10,15,20-三苯基卟啉]锌配合物以及[5- (4’-甲硫基-4-联苯基)-10,15,20-三苯基卟啉]锌配合物。并用Uv,‘H NMR, IR, Ms, Fs等表征确证了该系列配合物的结构,并用循环伏安法对以上部分产物进行了电化学性质的研究.     

新型尾式组氨酸卟啉的合成及性质

设计并合成了新型尾式氨基酸卟啉5-(Trt-组氨酸酰胺基苯基)-10,15,20-三苯基卟啉(Trt-His-NH2-TPP,1)及其金属卟啉配合物(Zn,Co,Fe,Mn,分别标记为2～5).通过元素分析、核磁共振氨谱、质谱、紫外-可见光谱和红外光谱等对化合物进行了表征,研究了它们的荧光性质,并通过理论模拟研究了其最...     

新型不对称卟啉配体及其锌配合物的合成与荧光性能

以3,5-二羟基苯甲酸丙酯和5-(4-硝基)苯基-10,15,20-三苯基卟啉为起始原料,合成了新型的不对称卟啉配体——5-[4-(3,5-二-十六烷氧基苯甲酰亚胺基)苯基]-10,15,20-三苯基卟啉(1)及其锌配合物(2),其结构经UV-Vis,1H NMR,IR和元素分析表征。用荧光激发光谱研究了1和2的荧光性能,结果表明:在激发波长为420 nm时,1和2的荧光发射峰分别在650 nm,709 nm和600 nm,644 nm。     

卟啉化合物的研究(ⅩⅩ)——5-(p-十六烷氧基苯基)-10,15,20-三苯基卟啉和5-(p-十六羰酰氧苯基)-10,15,20-三苯基卟啉的合成及光电性质的研究

在卟啉的苯环上接上4～30个碳的长链,则其光电化学性能增强,并成为性能良好的充电导膜材料及照相感光材料。为此,本文合成了5-(p-十六烷氧基苯基)-10,15,20-三苯基卟啉(Ⅱ)和5-(p-十六羰酰氧苯基)-10,15,20-三苯基卟啉(Ⅲ),合成路线如下:     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.