CO2加氢制备二甲醚CuO-ZnO-Al2O3/HZSM-5催化剂的研究

以无水乙醇为溶剂,草酸为沉淀剂,采用悬浮共沉淀法,一步合成CuO-ZnO-Al2O3/HZSM-5双功能催化剂.并研究了该催化剂在CO2加氢合成二甲醚反应中的催化性能,考察了CO2加氢合成甲醇组分(CuO-ZnO-Al2O3)与甲醇脱水组分(HZSM-5)配比对催化剂性能的影响以及催化剂的稳定性.结果表明,双功能催化剂加氢与脱水组分配比为8∶1时,对CO2加氢直接合成二甲醚有较高的催化性能:在固定床反应器中,温度为270℃,压力为3.0 MPa,空速为4 800 h-1的反应条件下,CO2的单程转化率达到29.8%,二甲醚的选择性和收率分别达到53.8%和16%.XRD、BET、TPR和NH3-TPD对催化剂结构表征结果表明,不同组分配比影响双功能复合催化剂中脱水组分的酸性和加氢组分的结晶度、晶粒尺寸、CuO的还原性.     

沉淀剂对悬浮共沉淀法制备二甲醚催化剂的影响

以无水乙醇为溶剂,将Cu、Zn和Al的硝酸盐并流共沉淀在HZSM-5分子筛的悬浮溶液中,一步合成CuO-ZnO-Al2O3/HZSM-5双功能催化剂.研究了沉淀剂的种类、加入顺序和加入量对催化剂活性的影响.结果表明,以适量的草酸作沉淀剂,采用悬浮液并流共沉淀法制备的双功能催化剂,对CO2加氢直接合成二甲醚有较高的催化性能:在固定床反应器中,温度为270℃,压力为3.0 MPa,空速为4 800 h-1的反应条件下,CO2的单程转化率达到28.7%,二甲醚的选择性达到53.2%.BET、XRD、TPR、TPD和N2O滴定等对催化剂结构表征结果表明,双功能复合催化剂CuO-ZnO-Al2O3/HZSM-5的结构影响CO2加氢合成二甲醚的催化性能.     

助剂Mn对CO2加氢制二甲醚CuO-ZnO-ZrO2/HZSM-5催化剂的结构和性能影响

以无水乙醇为溶剂,草酸为沉淀剂,采用悬浮共沉淀法,一步合成Mn改性的CuO-ZnO-ZrO2/HZSM-5双功能催化剂.并研究了该催化剂在CO2加氢合成二甲醚反应中的催化性能,考察了助剂锰的添加量对催化剂性能的影响,并采用XRD、BET、TPR、NH3-TPD和XPS对催化剂结构进行表征.结果表明,双功能催化剂性能与助剂锰的添加量有密切联系,适量锰的加入可提供合适的表面酸性,提高二甲醚的选择性,降低副产物CO的选择性.表征结果表明,加入Mn可以促进CuO的分散,并降低CuO的还原温度,增加催化剂的比表面积,提高Cu+/Cu0比,从而能促进CO2的转化,有利于提高催化剂的活性.     

尿素燃烧法制备CuO-ZnO/HZSM-5及其催化CO_2加氢合成二甲醚的性能

以尿素为燃烧剂,先采用燃烧法制备CuO-ZnO催化剂,接着采用研磨法将其与HZSM-5分子筛均匀混合形成CuO-ZnO/HZSM-5双功能催化剂.采用固定床反应器,在反应温度260℃、压力3.0 MPa、空速1 500 h-1条件下,考察了不同Cu/Zn(摩尔比)催化剂在CO_2加氢合成二甲醚反应中的催化性能.通过XRD、N_2等温吸附脱附、H2-TPR、NH3-TPD对催化剂进行表征,研究了不同Cu/Zn对催化剂结构及表面酸性的影响.结果表明:当Cu∶Z n=6∶4时,催化剂对CO_2催化加氢直接合成二甲醚反应的催化活性和选择性最佳,CO_2的转化率、DME的选择性分别为11.95%和28.74%,且在催化剂上具有更多的低温还原Cu和较强的酸中心,从而提高了CO_2加氢活性和二甲醚的选择性.     

完全液相法中Cu源对Cu-Zn-Al催化剂结构及性能的影响

采用完全液相法,分别以柠檬酸铜、硝酸铜、乙酸铜为Cu源制备了三种Cu-Zn-Al浆状催化剂,考察了不同铜源对催化剂催化合成气制二甲醚性能的影响,利用XRD、H2-TPR、NH3-TPD、BET、XPS和TEM等技术对催化剂进行了表征。结果表明,铜源对催化剂织构形貌及性能影响显著,用柠檬酸铜为铜源制备的催化剂铜物种分散性最好,铜物种与其他组分间相互作用强,可还原物质的量多,同时催化剂表面弱酸量与强酸量的比较高,催化剂的甲醇脱水能力提升,三种催化剂中柠檬酸铜催化剂性能最好,CO转化率为63.4%,二甲醚选择性为66.0%。     

助剂SiO2对CO2加氢制二甲醚催化剂Cu-ZnO/HZSM-5性能的影响

 考察了助剂SiO2对CO2加氢合成二甲醚催化剂Cu-ZnO/HZSM-5性能的影响,并用X射线衍射、程序升温还原和X射线光电子能谱等手段对催化剂进行了表征. 结果表明,加入少量的SiO2即可显著提高CO2的转化率、二甲醚的选择性以及二甲醚和甲醇的总选择性,并降低副产物CO的选择性,同时改善催化剂的稳定性; 但SiO2加入量大时,催化活性反而降低. SiO2的存在可使焙烧后催化剂的晶型结构发生改变,促进CuO和ZnO的分散,并提高CuO的还原温度. SiO2的加入抑制了反应过程中催化剂上Cu0和ZnO晶粒的长大,对活性物种Cu0有稳定作用,从而有利于提高催化剂的活性和稳定性.     

Cu/ZrO_2催化剂的结构及其CO_2加氢合成甲醇催化反应性能

采用低温氮气吸脱附、XRD、TPR、In-situ IR和XPS等表征手段,对分步沉淀法、浸渍沉淀法和固态反应法制备的CuO/ZrO2催化剂进行表征,同时考察了其CO2加氢合成甲醇反应性能。结果表明,制备方法对CuO/ZrO2的物理结构和还原性能影响很大,其中浸渍沉淀法制备的催化剂Cu与ZrO2相互作用最强,并显示了较高的CO2转化率和甲醇收率。Cu与ZrO相互作用的强弱直接影响CO加氢合成甲醇反应性能的优劣,而催化剂的比表面积不是影响反应性能的主导因素。     

有机酸配合剂对CuZnAl催化剂结构和性能的影响

以小分子有机酸(柠檬酸、草酸、酒石酸)为配合剂,乙二醇为胶凝剂,采用完全液相法制备系列CuZnAl催化剂,在浆态床反应器中进行CO加氢性能测试.利用XRD、H_2-TPR、NH_3-TPD、N_2物理吸附等方法对其结构进行表征,考察有机酸配合剂对催化剂结构性能的影响.结果表明,改变小分子有机酸种类及用量可以调变催化剂表面酸量和Cu~0晶粒尺寸,其中适当增加柠檬酸用量,有利于提高催化剂结构的稳定性,而弱酸量和Cu~0晶粒尺寸对低碳醇的生成有重要影响;反应温度对催化产物分布有显著影响,250℃有利于低碳醇生成,280℃二甲醚选择性明显增加,且二甲醚和低碳醇选择性呈负相关.     

SiO2改性的Cu-ZnO/HZSM-5催化剂及合成二甲醚性能

以廉价的硅酸钠为硅源，碳酸钠为沉淀剂，采用共沉淀沉积法制备了SiO2改性的Cu-ZnO/ HZSM-5催化剂，用XRD、SEM、H2-TPR、XPS等手段进行了表征，考察了对CO2加氢合成二甲醚的催化活性。结果表明，SiO2促进了催化剂前驱体的分散，延缓了焙烧后催化剂晶粒的长大和颗粒的团聚。SiO2改性的同时影响了CuO的分布状态及还原过程。1.0%SiO2改性的Cu-ZnO/HZSM-5催化剂，用于CO2加氢合成二甲醚，CO2转化率和二甲醚的收率达28.53%和16.34%，与未经改性的Cu-ZnO/ HZSM-5相比，CO2转化率和二甲醚收率分别提高了20%和34%；继续增大SiO2用量，催化剂的活性反而降低。XPS和AES表征表明，1.0%SiO2改性的Cu-ZnO/HZSM-5催化剂中，Cu0是甲醇合成的活性中心，锌以ZnO的形式存在。     

CO2加氢合成二甲醚的催化剂的制备

先采用均匀沉淀法制备出CuO—ZnO催化剂,然后以CuO—ZnO催化剂作为晶核采用水热合成法制备出CuO—ZnO／HZSM-5（氢型ZSM-5分子筛）复合催化剂．利用X射线衍射和氨程序升温脱附手段对复合催化剂进行表征,并应用于CO2催化加氢合成二甲醚的反应．研究结果表明,在相同的反应条件下,这种CuO—ZnO／HZSM-5复合催化剂与采用物理混合法制备出的复合催化剂相比具有更好的催化效果,不但提高了CO2的转化率、二甲醚的选择性以及二甲醚和甲醇的总选择性,同时还改善了催化剂的稳定性．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。