加速器质谱测量用NH4Hf2F9的制备及表征

研究了加速器质谱测量用NH4Hf2F9的制备方法,用XRD,SEM,XPS和TG-DTA表征其结构和组成.结果表明:NH4Hf2F9样品在573 K热处理1 h后物相并未变化,而在773,973,1173,1373 K热处理1 h后物相则都转变为HfO2.TG-DTA的分析表明从573 K开始NH4Hf2F9样品逐渐开始分解,至1073 K时失重约78%.样品微观形貌为不规则的固体颗粒,颗粒的粒径分布较大,范围在5～20μm之间.粉末样品主要含有Hf,N和F元素,其中Hf主要以(+4)价存在.     

固相萃取-气相色谱/质谱法同时测定涂料中的8种有机锡

建立了一种固相萃取（SPE）前处理、气相色谱-质谱（GC-MS）法同时测定涂料中8种有机锡的方法。样品采用阳离子交换固相萃取小柱净化,最佳固相萃取条件为：固相萃取小柱分别用5mL甲醇、7mL洗脱液（氯化铵、甲醇、冰乙酸的混合溶液）预洗,10mL甲醇活化;将用甲醇稀释的涂料样品上样后,用5mL甲醇淋洗,抽干2min,7mL乙酸-氯化铵甲醇溶液（10：90,V／V）洗脱溶液洗脱。洗脱液用四乙基硼化钠溶液衍生后,气相色谱-质谱法进行定性定量分析。结果表明：以标准加入法计算回收率,在1.68％-16.84%添加范围内,平均回收率在85％-105％之间,相对标准偏差均小于12％。     

Et2NH2[Nd(S2CNEt2)4]的晶体结构和生成反应焓变

在干燥氮气气氛下,以无水乙醇为溶剂,制备了低水合氯化钕与二乙氨基荒酸二乙铵(D-DDC)配合物,确定其组成为Et2NH2[Nd(S2CNEt2)4].单晶结构分析表明,配合物中4个二乙氨基荒酸根各通过2个硫原子与钕离子成键形成八配位十二面体阴离子,并与二乙铵阳离子形成缔合型分子.晶体属单斜晶系,空间群P21/n,a=1.37517(14)nm,b=2.1146(2)nm,c=1.44641(15)nm,β=102.028(2)°,Z=4.用微量热法测定了298.15K下水合氯化钕和D-DDC在无水乙醇中的溶解焓及二乙氨基荒酸钕液相生成反应焓变分别为(-17.89±0.096),(50.280±0.151)和(-10.116±0.065)kJ/mol,求得固相生成反应焓变.     

亚甲基蓝及NH4+,Na+,K+与SiO2的表面配位常数测定

采用动电位、等温吸附方法研究了不同pH条件下SiO2的表面电性和对有机染料-亚甲基蓝的吸附行为,运用WinSGW软件计算得出亚甲基蓝在SiO2颗粒表面配位常数.研究发现亚甲基蓝通过静电和氢键作用吸附,相应的化学反应模型和表面配位常数分别为≡Si2O-+MB+≡Si2OMB(lg K=4.48)和≡SiOH+MB+≡SiOHMB+(lg K=2.30).在此基础上研究了一价阳离子NH+4,Na+,K+对亚甲基蓝在SiO2表面吸附的影响,根据WinSGW软件模拟得到的NH+4,Na+,K+与SiO2表面的配位常数分别为:≡Si2O-+M+≡Si2OM[lg K=3.76,2.73,2.58(M+=NH+4,Na+,K+).在铵根离子浓度高时,还会在表面上发生≡SiOH+NH3+MB+≡SiOHNH3MB+(lg K=6.69)化学反应而生成包含有三种组分的≡SiOHNH3MB+表面三元配合物.研究结果可为了解有机染料和氨氮在被污染土壤和水体中的分布提供一定的理论依据.     

烟酸钠Na(C6H4NO2)(s)的低温热容和热化学

选择分析纯烟酸和无水醋酸钠作为反应物, 用室温固相合成方法合成了无水烟酸钠. 利用FTIR和X射线粉末衍射等方法进行了表征, 利用化学分析和元素分析确定其组成为Na(C6H4NO2). 用精密自动绝热热量计测量其在78~400 K温度区间的低温热容. 研究结果表明, 该化合物在此温度区间无热异常现象发生. 用最小二乘法将实验摩尔热容对温度进行拟合, 得到热容随温度变化的多项式方程. 用此方程进行数值积分, 得到在此温度区间每隔5 K的舒平热容值和相对于298.15 K时的热力学函数值. 在此基础上, 通过设计合理的热化学循环, 选用1 mol/L NaOH溶液作为量热溶剂, 利用等温环境溶解-反应热量计分别测得固相反应的反应物和产物在所选溶剂中的溶解焓, 得到固相反应的反应焓. 最后, 计算出无水烟酸钠的标准摩尔生成焓为: ΔfHm0[Na(C6H4NO2), s]=-(548.96±1.11) kJ/mol.     

离子交换固相萃取高效液相色谱联用法检测河豚鱼中的河豚毒素

优化建立了采用混合模式阳离子交换固相萃取柱代替传统的C18固相萃取柱进行前处理,联用高效液相色谱检测河豚鱼中河豚毒素的方法.样品经合1％乙酸的乙腈甲醇(3:1,V:V)溶液提取,混合模式阳离子交换固相萃取柱(MCX)净化,5％氨水/甲醇溶液洗脱,采用高效液相色谱-二极管阵列检测器(HPLC-PAD)测定,外标法定量.河...     

近紫外光激发的新型蓝色荧光粉YVxP1-xO4:Ta5+的合成与发光性能

采用高温固相法成功合成了Y(V,P)O4:Ta荧光粉,并利用XRD,激发光谱和发射光谱对所合成粉体的物相结构及发光性能进行了表征。实验结果表明:粉体的结构属于锆英石结构;粉体在310 nm波长的激发下,发射光谱的主峰位于450 nm,属于Ta5+的3p63d10→3p53d104d1跃迁,当n(V)/n(P)为0.3/0.7和Ta5+的摩尔掺杂浓度为0.01时,粉体的发光性能最佳;用不同浓度NH4NO3做助熔剂制备YV0.3P0.7O4:Ta50.+01荧光粉,发现NH4NO3的摩尔浓度为5%时,粉体的发光强度最强。     

稀土-天冬氨酸-咪唑配合物Sm2(Asp)2(Im)6(ClO4)6.6H2O的特殊低温相变和热力学性质

合成了标题配合物,测定了其晶体在80~385 K温度范围的等压摩尔热容,低温区间的绝热量热和差示扫描量热均发现配合物在220K和245K附近存在固-固相转变,推测其机理可能是配合物中高氯酸根的重取向运动不同阶段所造成;根据实验热容数据和热力学公式,计算出配合物在80~385 K温度区域内相对于298.15K的标准热力学函数[HT-H298.15]和[ST-S298.15],根据热容测定数据计算出该相变的焓变和熵变。用热重法检测了配合物的热稳定性并推测其热分解机理。这两个低温区相变过程的发现,使开发此类配合物作为新低温相变材料成为可能。     

苯氧威 (C17H19NO4) 的热容和热力学性质

通过小样品精密自动绝热量热计测定了自己合成并提纯的苯氧威 (C₁₇H₁₉NO₄) 在79 ～ 360 K温区的低温摩尔热容。量热实验发现, 该化合物在320 ~ 330 K温区, 有一固 - 液熔化相变过程, 其熔化温度为（326.31±0.14）K, 摩尔熔化焓、摩尔熔化熵及化合物的纯度分别为：(26.98±0.04) kJ• mol^-1和（82.69 0.09）J•mol^-1•K^-1和 (99.53±0.01 )%。并计算出了80-360 K的热力学参数。用分步熔化法得到绝对纯化和物的熔点为326.60±0.06 K。用差示扫描量热 (DSC) 技术对该物质的固-液熔化过程作了进一步研究，结果与绝热量热法一致。     

化妆品中阴阳离子的快速测定及其用于化妆品鉴别的研究

用离子色谱电导检测器对黑泥类化妆品中的阴、阳离子(Na+,NH+4,K+,Mg 2+ ,Ca 2+ ,Cl-,Br-,NO-2,NO-3和SO 2- 4)进行了测定。阳离子分离条件: 阳离子交换柱ICS C25,均苯四甲酸淋洗液浓度2.0 mmol/L ,流速0.6 mL/min ;阴离子分离条件: 阴离子交换柱Shim pack IC A1,淋洗液为2.5 mmol/L 邻苯二甲酸和2.4 mmol/L 三羟基氨基甲烷,流速1.0 mL/min 。结果表明,上述10种离子在较宽浓度范围内有良好     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.