高效液相色谱法对纺织品和食品包装材料中的壬基酚、辛基酚和双酚A的同时测定

建立了高效液相色谱-二极管阵列检测器(DAD)/荧光检测器(FLD)串联技术同时测定纺织品和食品包装材料中壬基酚、辛基酚和双酚A的方法.实验样品采用加速溶剂萃取法,以无水乙醇为提取溶剂,在10.3 MPa和120 ℃下静态循环提取2次,提取液经Supelclean Envi-Carb石墨化碳黑固相萃取柱净化,以Agilent Zorbax SB-Phenyl(250 mm×4.6 mm,5 μm)色谱柱分离后用DAD-FLD串联法进行检测.壬基酚、辛基酚和双酚A的DAD检测波长为225 nm;荧光激发波长为227 nm,发射波长为315 nm.在25、50、500 μg/kg的添加水平下,纺织品样品和食品包装材料样品的平均回收率均为93% ～98%,相对标准偏差分别为2.8% ～7.0%和2.9% ～6.9%.方法准确、简便、快速,可用于纺织品和食品包装材料的实际检验工作.     

固相萃取-高效液相色谱法测定水中BPA、NP和OP含量

采用国产新型D4020大孔吸附树脂自制固相萃取柱,研究了柱长、上样速度、样品溶液的pH、盐浓度等因素对壬基酚、辛基酚和双酚A吸附率的影响,确定了最佳固相萃取条件,建立了固相萃取-高效液相色谱测定水中痕量壬基酚、辛基酚和双酚A的分析方法.该法双酚A、壬基酚和辛基酚的检出限分别为0.432 μg/L、0.998 μg/L和1.336 μg/L,回收率为91%～96%,相对标准偏差(RSD)为1.5%～5.6%.方法简便快速、成本低廉,灵敏度高,准确度好,用于实际水样分析,取得满意结果.     

超高效液相色谱–串联质谱法测定食品接触材料中烷基酚物质迁移量

建立了超高效液相色谱-串联质谱法测定食品接触材料中双酚A、四溴双酚A、壬基酚和辛基酚迁移量的方法。样品经蒸馏水、3%乙酸溶液、10%乙醇溶液、20%乙醇溶液、50%乙醇溶液和异辛烷6种食品模拟物浸泡处理,浸泡液经C18色谱柱分离,以多反应监测(MRM)模式进行定性和定量。检测结果表明:在水基、酸性、酒精类食品模拟物中,双酚A、四溴双酚A、壬基酚、辛基酚的质量浓度均在0.001~0.50μg/mL范围内与其质谱响应值具有良好的线性关系,相关系数均不小于0.9995,方法检出限为0.01~0.25μg/kg,定量限为0.03~0.83μg/kg;在油基食品模拟物中,双酚A、四溴双酚A、壬基酚、辛基酚的线性范围均为0.01~0.50μg/mL,相关系数均不小于0.9989,方法检出限为0.10~2.50μg/kg,定量限为0.33~8.32μg/kg。双酚A、四溴双酚A、壬基酚、辛基酚的加标回收率为87.2%~101.2%,相对标准偏差为1.5%~3.4%(n=6)。该法样品处理步骤简单,准确度高,灵敏度好,可用于食品接触材料中烷基酚类化合物的检测。     

高效液相色谱法测定大鼠组织中双酚A和4-壬基酚浓度

建立了大鼠组织中双酚A和4-壬基酚的提取和含量测定方法。大鼠组织样品经甲醇-乙酸铵缓冲液匀浆、 正己烷-乙醚混合溶剂提取、氮气吹干后用流动相溶解,以乙腈-0.01 mol/L乙酸铵缓冲液(pH 4.5)(体积比为75∶25)为流动相,经C18色谱柱分离,在激发波长227 nm、发射波长313 nm下进行荧光检测。大鼠心、脑、肝和肾脏组织样品中,双酚A的检出限为3.2~4.6 ng/g,4-壬基酚的检出限为11.8~15.6 ng/g;日内检测精密度为0.89%~4.50%,日间检测精密度为3.10%~12     

同位素稀释液相色谱-串联质谱法测定动物性食品中的双酚A、壬基酚及辛基酚

建立了动物性食品肉、蛋和奶中双酚A、壬基酚和辛基酚的超高效液相色谱-串联质谱( UPLC-MS/MS)检测方法.比较了固相萃取法(SPE)和凝胶渗透色谱法(GPC)两种前处理技术,探讨了前处理过程中目标化合物背景污染的来源.最终采用乙酸乙酯-环己烷(1∶1,V/V)超声提取,经GPC净化后进行超高效液相色谱串联质谱分析.3种目标化合物的线性范围为0.25～1600 μg/L,相关系数R2＞ 0.999;对肉和鸡蛋样品,方法的定量限( LOQ)为0.2μg/kg;奶粉样品的LOQ为0.4 μg/kg.目标化合物在3个不同水平的加标回收率为85.9％～117.0％,RSD＜ 20％.应用本方法对市售动物性食品肉、蛋和奶进行了分析,壬基酚的检出率最高,含量为0.27～1357 μg/kg,此外还检出了双酚A.     

液相色谱-串联质谱法同时测定纺织品和食品包装材料中的壬基酚、辛基酚和双酚A

建立了纺织品和食品包装材料中壬基酚、辛基酚和双酚A的液相色谱-串联质谱分析方法。不同类型的纺织品和食品包装材料样品采用加速溶剂萃取法,以无水乙醇为提取剂,在10.3 MPa和120℃下静态循环提取2次,提取液经Supelclean Envi-Carb石墨化碳黑固相萃取柱净化,收集甲醇-二氯甲烷(1∶4,V/V)洗脱液,采用Waters XBridge C18色谱柱,以甲醇-0.1%氨水溶液为流动相,梯度洗脱分离后,在LC/MS/MS多反应监测模式下进行定性与定量分析。壬基酚、辛基酚和双酚A的方法检出限为0.5μg/kg,在0.5～10μg/kg的3个添加水平范围内,纺织品样品的平均回收率为86.9%～92.5%,相对标准偏差均小于9.1%;食品包装材料样品的平均回收率为87.8%～93.0%,相对标准偏差均小于8.8%。本方法准确、快速、灵敏度高,可用于纺织品和食品包装材料的实际检验。     

高效液相色谱分析食品罐内涂料中双酚A和双酚F环氧衍生物残留

建立了高效液相色谱分析食品罐内涂料中双酚A(BPA)和双酚F(BPF)环氧衍生物的方法.样品经乙腈提取后,旋转蒸发浓缩至干,以V(乙腈)∶ V(水)=50∶ 50混合液溶解并定容;采用Lichrospher C18柱,以乙腈/水为流动相梯度洗脱,进行高效液相色谱分离;荧光检测器检测,激发波长230 nm,发射波长301 nm.在2.3～230 μg/L浓度范围内,各BPA和BPF环氧衍生物的响应峰面积与其相应浓度呈良好相关性,检出限为0.57～6.55 μg/L;在80～400 μg/L添加水平范围内,平均添加回收率为85%～107%;相对标准差小于7.4%.结果表明,本方法适用于食品罐内涂料中BPA和BPF环氧衍生物残留分析.     

加速溶剂萃取-液相色谱-质谱/质谱法分析动物组织中的壬基酚、辛基酚和双酚A

建立了测定内分泌干扰物质烷基酚、双酚A的液相色谱-电喷雾串联质谱(负离子模式)分析方法,优化了样品前处理方法。以二氯甲烷作提取溶剂,采用加速溶剂萃取法萃取动物组织样品,萃取液用500 mg OASIS氨基固相萃取柱进行浓缩净化。对流动相组分和流动相添加剂对质谱的离子化效率进行了考察,测得3种化合物在高、中、低3个添加水平的回收率为88%~101%,相对标准偏差小于15%;双酚A、壬基酚和辛基酚的方法检出限分别为0.3, 0.05和0.1 μg/kg。对从北京市场上采集的27份动物组织样品进行检测,结果表明壬基酚广泛存在于各种动物源性食品中,检出含量为0.49~55.98 μg/kg,其中鱼肉组织中都检出壬基酚,而且其含量也较高(9.13~55.98 μg/kg)。     

液相色谱串联质谱法测定化妆品中的双酚A、辛基酚及壬基酚

建立了护肤化妆品中双酚A、辛基酚和壬基酚的超高效液相色谱串联质谱分析方法。样品经二氯甲烷提取,氨基固相萃取柱净化后,用甲醇定容,采用Waters UPLC BEH C18色谱柱,以甲醇-0.05%氨水为流动相,梯度洗脱分离后,串联四极杆质谱多反应监测方式检测,以保留时间和子离子比定性,外标法定量。在优化条件下,该方法 5 min内可完成4种待测物的分析。双酚A、辛基酚和壬基酚在0.5～50.0μg/L范围内线性关系良好,相关系数均大于0.999,方法的定量下限(LOQs)均为0.5μg/kg;在加标水平为0.5、1.0、10.0μg/kg时,护肤霜和护肤水样品中4种待测物的平均加标回收率为80%～96%,相对标准偏差(n=6)小于15%。该方法准确、快速、灵敏,适用于护肤化妆品中双酚A、辛基酚和壬基酚的快速确认和定量检测。     

高效液相色谱-串联质谱法测定儿童和成人尿液中双酚A、四溴双酚A和辛基酚

采用高效液相色谱-串联质谱法定量检测人体尿液中痕量双酚A、四溴双酚A和辛基酚.将解冻后的尿样酶解,经液液萃取、旋蒸至干,甲醇定容后分析.3种目标物质在0.2～50 μg/L质量浓度范围内线性关系良好,相关系数均大于0.99,定量限(LOQ)在0.05 ～ 0.27 μg/L之间.在5,10和50 μg/L加标水平下,平均回收率为85.7％～118.6％,相对标准偏差RSD(n=3)为4.1％ ～10.5％.20组儿童与成人的尿样结果表明,尿样中均检出3种目标物,其中,四溴双酚A和辛基酚在儿童及成人尿样中的暴露浓度基本相同,但是双酚A的暴露水平具有显著性差异(儿童＞成人).     

Furyl- and thienyl-silatranes and germatranes

We review our research on the synthesis and study of the physical and biological properties of furyl- and thienylgermatranes and -silatranes.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 725–732, June, 1992.     

Review and patents and literature

The use of the insect cell/baculovirus expression system for producing recombinant proteins of bacterial, plant, insect, and mammalian origin has become widespread. The popularity of this eukaryotic expression system is due to many factors, including (1) potentially high protein expression levels, (2) ease and speed of genetic engineering, (3) ability to accommodate large DNA inserts, (4) protein processing similar to higher eukaryotic cells (e.g., mammalian cells), and (5) ease of insect cell growth (e.g., suspension growth). The following review of the literature discusses two engineering aspects of recombinant protein synthesis by insect cell cultures: bioreactor scale-up and insect cell line selection. Following this review patent abstracts and additional literature pertaining to expression of recombinant proteins in insect cell culture are listed.     

Ground- and excited-state aromaticity and antiaromaticity in benzene and cyclobutadiene

The aromaticity and antiaromaticity of the ground state (S 0), lowest triplet state (T 1), and first singlet excited state (S 1) of benzene, and the ground states (S 0), lowest triplet states (T 1), and the first and second singlet excited states (S 1 and S 2) of square and rectangular cyclobutadiene are assessed using various magnetic criteria including nucleus-independent chemical shifts (NICS), proton shieldings, and magnetic susceptibilities calculated using complete-active-space self-consistent field (CASSCF) wave functions constructed from gauge-including atomic orbitals (GIAOs). These magnetic criteria strongly suggest that, in contrast to the well-known aromaticity of the S 0 state of benzene, the T 1 and S 1 states of this molecule are antiaromatic. In square cyclobutadiene, which is shown to be considerably more antiaromatic than rectangular cyclobutadiene, the magnetic properties of the T 1 and S 1 states allow these to be classified as aromatic. According to the computed magnetic criteria, the T 1 state of rectangular cyclobutadiene is still aromatic, but the S 1 state is antiaromatic, just as the S 2 state of square cyclobutadiene; the S 2 state of rectangular cyclobutadiene is nonaromatic. The results demonstrate that the well-known "triplet aromaticity" of cyclic conjugated hydrocarbons represents a particular case of a broader concept of excited-state aromaticity and antiaromaticity. It is shown that while electronic excitation may lead to increased nuclear shieldings in certain low-lying electronic states, in general its main effect can be expected to be nuclear deshielding, which can be substantial for heavier nuclei.     

Hard and soft acids and bases: structure and process

Under investigation is the structure and process that gives rise to hard-soft behavior in simple anionic atomic bases. That for simple atomic bases the chemical hardness is expected to be the only extrinsic component of acid-base strength, has been substantiated in the current study. A thermochemically based operational scale of chemical hardness was used to identify the structure within anionic atomic bases that is responsible for chemical hardness. The base's responding electrons have been identified as the structure, and the relaxation that occurs during charge transfer has been identified as the process giving rise to hard-soft behavior. This is in contrast the commonly accepted explanations that attribute hard-soft behavior to varying degrees of electrostatic and covalent contributions to the acid-base interaction. The ability of the atomic ion's responding electrons to cause hard-soft behavior has been assessed by examining the correlation of the estimated relaxation energies of the responding electrons with the operational chemical hardness. It has been demonstrated that the responding electrons are able to give rise to hard-soft behavior in simple anionic bases.     

Determination and study on residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil

A QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for the determination of benazolin-ethyl and quizalofop-p-ethyl in rape and soil by high-performance liquid chromatography-tandem mass spectrometry has been developed in this study. The residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil were determined with the developed method. The half-lives of benazolin-ethyl in rape straw and soil were 3.7–5.1 days and 14.3–26.3 days, respectively. The half-lives of quizalofop-p-ethyl in rape straw and soil were 5.0-6.1 days and 0.3–9.7 days, respectively. The residue of benazolin-ethyl and quizalofop-p-ethyl in rapeseed and soil were below the detection limit (i.e., 0.5?mg?kg^?1, the maximum residue level of European Union for quizalofop-p-ethyl).     

Syntheses and structures of P-anilino-P-chalcogeno- and P-anilino-P-iminodiazasilaphosphetidines and their group 12 and 13 metal compounds

The P-anilino-P-chalcogeno(imino)diazasilaphosphetidines [Me(2)Si(mu-N(t)Bu)(2)P=E(NHPh)] (E = O (3), S (4), Se (5), N-p-tolyl (6)) were synthesized by oxidizing the P-anilinodiazasilaphosphetidine [Me(2)Si(N(t)Bu)(2)P(NHPh)] (2) with cumene hydroperoxide, sulfur, selenium, and p-tolyl azide, respectively. The lithium salt of 4 reacted with thallium monochloride to produce ([Me(2)Si(mu-N(t)Bu)(2)P=S(NPh)-kappaN-kappaS]Tl)(7), which features a two-coordinate thallium atom. Treatment of 4-6 with AlMe(3) gave the monoligand dimethylaluminum complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE]AlMe(2)) (E = S (8), Se (9), N-p-tolyl (10)), respectively. In these complexes the aluminum atom is tetrahedrally coordinated by one chelating ligand and two methyl groups, as a single-crystal X-ray analysis of 8 showed. A 2 equiv amount of 4-6 reacted with diethylzinc to produce the homoleptic diligand complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE](2)Zn)(E = S (11), Se (12), N-p-tolyl (13)). A crystal-structure analysis of 11 revealed a linear tetraspirocycle with a tetrahedrally coordinated, central zinc atom.