全硅MCM-41担载的加氢脱硫催化剂的TPR研究

用TRP技术研究了以全硅MCM-41(Si-MCM-41)和HNO3交换的全硅MCM-41(H-MCM-41)为载体制备的Ni-Mo、Co-Mo和Ni-W加氢脱硫(HDS)催化剂的还原性能，并以0．8(wt)％二苯并噻吩(DBT)的十氢萘溶液为模型化合物，在高压固定床反应器上考察了上述催化剂的加氢脱硫(HDS)反应性能。结果表明，Si-MCM-41经稀HNO3交换后，所担载的Ni-Mo和Ni-W催化剂还原性能、HDS活性和加氢活性有显著变化，但对Co-Mo催化剂影响不大。这说明在Ni-Mo／H-MCM-41和Ni-W／H-MCM-41中可能存在氢溢流现象，DBT的HDS活性与载体表面酸性和氢溢流有关。     

NiMoS/γ-Al2O3上二苯并噻吩加氢脱硫和喹啉加氢脱氮反应的相互影响

在固定床高压微反装置上,考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩(DBT)加氢脱硫(HDS)反应和喹啉加氢脱氮(HDN)反应之间的相互影响.结果表明,喹啉对DBT的HDS反应具有强烈的抑制作用,其中对加氢路径比氢解路径的抑制作用更强,这是由喹啉及其HDN反应的中间产物与DBT在活性位上的竞争吸附造成的.在300和340℃时,喹啉对DBT的HDS反应中氢解路径的抑制程度与其HDN中间产物的相对含量紧密相关.而DBT能够提高喹啉的脱氮能力,这源于其HDS产物H2S.H2S促进了催化剂表面硫阴离子空穴向B酸位的转化,从而提高了喹啉HDN中间产物分子的C(sp3)-N键的断裂能力.HDN活性相的保持不需要过多的硫原子.     

压力和温度对4-甲基二苯并噻吩和二苯并噻吩加氢脱硫反应的影响

研究了4-甲基二苯并噻吩(4-MDBT)和二苯并噻吩(DBT)在CoMo/γ-Al2O3上的加氢脱硫反应产物分布及其可能的反应网络,通过反应压力和温度对产物分布影响的研究,揭示了加氢脱硫反应的可能机理。研究发现4-MDBT在CoMo/γ-Al2O3上的加氢脱硫反应主要通过直接氢解路径和加氢路径进行,且两者反应速率相当；DBT在 CoMo/γ-Al2O3上的加氢脱硫反应主要通过直接氢解路径进行。4-MDBT分子位于4位的甲基阻碍其在催化剂表面通过硫原子的端连吸附,从而降低了其直接氢解脱硫路径的反应速率,因而也降低了其总的加氢脱硫转化率。反应压力降低,DBT和4-MDBT加氢脱硫反应中加氢路径反应速率明显下降,而其对氢解路径影响较小,但效果却与加氢路径相反,反应压力对4-MDBT转化率的影响大于DBT。反应温度对DBT和4-MDBT加氢脱硫反应中加氢路径和氢解路径都有明显影响,但是对DBT加氢脱硫反应中氢解路径的影响小于加氢路径,而对4-MDBT加氢脱硫反应中氢解路径的影响稍高于加氢路径,4-MDBT分子中甲基的供电子作用有利于相连苯环的加氢反应。     

工业NiW/Al2O3催化剂上二苯并噻吩的加氢脱硫动力学

以二苯并噻吩(DBT)为含硫模型化合物， 在高压滴流床反应装置中，考察了工业NiW/Al2O3催化剂（RN-10）的加氢脱硫(HDS)动力学规律，研究了氢分压（1.5 MPa～4.5 MPa）、氢油体积比（150~700）、液体质量空速(15 h-1~60 h-1）、反应温度（280 ℃~380 ℃）等对DBT的HDS反应结果的影响。结果表明，当氢分压和氢油体积比较大时，两者变化对DBT的转化率基本无影响；温度对DBT的转化率影响较大，提高温度可有效提高DBT的转化率，随着温度的升高，DBT转化率的增加逐渐变缓。采用2级平推流反应动力学模型对不同温度实验数据进行了拟合，求得了不同温度的表观反应速率常数，模型的相关系数>0.989。活化能计算结果表明，RN-10催化剂在高反应温度区(>330 ℃)的DBT的HDS活化能明显低于较低温度时的活化能，分别为13.4 kJ/mol和121.4 kJ/mol。对于RN-10催化剂，不可单纯地通过提高反应温度来大幅度提高HDS转化率。     

含镍WP/MCM-41催化剂二苯并噻吩加氢脱硫性能

以MCM-41为载体,以镍（Ni）为助剂,制备了Ni含量不同的WP/MCM-41催化剂。采用XRD、BET、SEM和XPS对催化剂进行了表征;以二苯并噻吩（DBT）为模型化合物,通过高压微反装置考察催化剂的加氢脱硫（HDS）活性。结果表明,Ni的加入促进了活性组分WP的生长并使其晶相尺寸略有增加,一定含量的Ni有利于提高催化剂的比表面积。Ni对WP/MCM-41催化剂二苯并噻吩HDS反应具有促进作用。少量Ni的加入有利于WP活性相的生成并增加了活性位的数量;加入过量的Ni,在催化剂中形成了具有一定活性的类似Ni-W-P结构的物种,减少了活性组分WP所占的比例,从而使催化剂DBT的 HDS活性降低。其中,Ni的质量分数为1%的催化剂（cat-Ni-1）具有相对较高活性,其DBT 脱硫率和转化率分别为76.78%和72.16%,比不加Ni的催化剂分别提高了30.04%和21.62%。二苯并噻吩在WP/MCM-41催化剂上以加氢脱硫途径为主,Ni的加入对提高加氢脱硫途径选择性起到了促进作用,且加氢脱硫选择性随Ni含量的增加而提高。     

Ni-Mo2N/SiO2复合纳米催化剂的制备及其对四氢萘加氢的催化活性

采用程序升温氮化法制备了Mo2N/SiO2,在此基础上负载Ni盐,制备了Ni-Mo2N/SiO2复合纳米催化剂,并考察了催化剂对四氢萘加氢的催化活性.结果表明,与Ni2Mo3N/SiO2及Ni/SiO2催化剂相比,Ni-Mo2N/SiO2复合催化剂具有较高的催化活性.采用"分离床"方法研究了Ni和Mo2N对四氢萘加氢活性的影响.通过X射线粉末衍射、透射电镜、氢吸附、元素分析和比表面积测定等技术对Ni-Mo2N/SiO2催化剂进行了表征.结果表明,与Ni/SiO2催化剂相比,Ni-Mo2N/SiO2复合催化剂中Ni的分散度并未提高;催化活性的提高归因于Ni与Mo2N在四氢萘加氢中的协同作用.氮化物的引入增加了芳烃吸附活性位的数目.提出了四氢萘在Ni-Mo2N/SiO2催化剂上的可能加氢机理.     

Pt对Ni2P/MCM-41催化剂加氢脱硫性能的影响

以MCM-41为载体, 采用程序升温还原法制备了含有少量Pt的Ni-P/MCM-41催化剂, 并用氢气程序升温还原(H₂-TPR)、 X射线衍射(XRD)、 N₂吸附比表面积、 X射线光电子能谱(XPS)和透射电子显微镜(TEM)对催化剂的结构和性能进行了表征. 考察了P/Ni摩尔比及Pt含量对Ni-P/MCM-41催化剂催化二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响. 结果表明, Pt能降低Ni₂P催化剂的还原温度, 并有助于Ni₂P相的生成, 抑制团聚现象, 提高催化剂的HDS活性. 当Pt的质量分数为0.6%, P/Ni摩尔比为2时, 催化剂具有最佳加氢脱硫活性, 在340 ℃, 3.0 MPa, 氢油体积比为500, 质量空速(WHSV)为2.0 h^-1的条件下, 二苯并噻吩转化率为100%, 且催化剂加氢脱硫活性在120 h内基本保持稳定.     

二苯并噻吩和吲哚在NiMoS/γ-Al2O3上加氢脱硫和加氢脱氮反应的相互影响

在固定床高压微反装置上考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩（DBT）加氢脱硫（HDS）反应和吲哚加氢脱氮（HDN）反应之间的相互影响。结果表明,吲哚对DBT的加氢脱硫反应具有抑制作用,其中对加氢路径（HYD）比对氢解路径（DDS）的抑制作用强,温度升高后,吲哚的抑制作用减弱。吲哚对DBT加氢脱硫反应的抑制作用源于吲哚及其HDN反应的中间产物在活性位上的竞争吸附。DBT和原位生成的H2S促进了催化剂表面硫阴离子空穴（CUS）向B酸位的转化,从而提高1,2-二氢吲哚（HIN）分子中C（sp3）—N键的断裂能力,使得吲哚的转化率和产物中邻乙基苯胺（OEA）的相对含量增大。HDN活性相的形成虽然需要硫原子的参与,但是活性相的保持并不需要大量的硫原子,较高含量硫化物存在时加氢活性位减少,不利于脱氮反应。     

二苯并噻吩和吲哚在NiMoS/γ-Al2O3上加氢脱硫和加氢脱氮反应的相互影响

在固定床高压微反装置上考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩（DBT）加氢脱硫（HDS）反应和吲哚加氢脱氮（HDN）反应之间的相互影响。结果表明,吲哚对DBT的加氢脱硫反应具有抑制作用,其中对加氢路径（HYD）比对氢解路径（DDS）的抑制作用强,温度升高后,吲哚的抑制作用减弱。吲哚对DBT加氢脱硫反应的抑制作用源于吲哚及其HDN反应的中间产物在活性位上的竞争吸附。DBT和原位生成的H2S促进了催化剂表面硫阴离子空穴（CUS）向B酸位的转化,从而提高1,2-二氢吲哚（HIN）分子中C(sp3)—N键的断裂能力,使得吲哚的转化率和产物中邻乙基苯胺（OEA）的相对含量增大。HDN活性相的形成虽然需要硫原子的参与,但是活性相的保持并不需要大量的硫原子,较高含量硫化物存在时加氢活性位减少,不利于脱氮反应。     

HY/MCM-41/γ-Al2O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

 采用水热法合成了不同SiO2/Al2O3比的MCM-41介孔分子筛. 并分别以HY/MCM-41/γ-Al2O3, HY/γ-Al2O3和γ-Al2O3为载体,用浸渍法制备了Mo-Ni-P催化剂. 以萘为模型化合物,考察了硫化态Mo-Ni-P催化剂的加氢活性. 结果表明,不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高,其中掺杂大比表面MCM-41的HY/MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大. 由于MCM-41与HY分子筛在酸性和孔结构上存在互补性,因而催化剂对萘加氢存在协同作用. 提出了萘加氢的反应机理,认为反应网络包括两个平行路径: 一是萘加氢生成四氢萘后发生异构化或开环反应; 二是萘加氢生成四氢萘后进一步加氢生成十氢萘,继而发生异构化或开环反应.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.