氯化钠在球形纳米氧化铈形成过程中的作用

以水合碳酸铈为原料, 以氯化钠作为助磨剂和阻聚剂, 采用机械活化法制备了球形纳米氧化铈, 用XRD法研究了水合碳酸铈与氯化钠质量比、球磨时间、煅烧温度对CeO2粉体晶粒度的影响, 用TEM对最终产物粒子进行形貌观察. 结果表明: 在碳酸铈的球磨过程及其随后的煅烧过程中, 氯化钠的存在起到了很好的助磨和阻聚作用, 所得CeO2为类球形粒子, 分散性较好, 晶粒度约为30～50 nm.     

影响纳米CeO2沉淀法合成的工艺因素研究

以Ce(NO3)3·6H2O为铈源, (NH4)2CO3·H2O为沉淀剂, 加入少量表面活性剂作分散剂, 采用液相沉淀法成功合成了纳米CeO2. 研究了反应温度、反应时间、搅拌速率、表面活性剂种类及用量、焙烧温度和焙烧时间等因素对纳米CeO2晶粒尺寸和相对密度的影响, 得出优化工艺条件, 通过XRD, DTA/TG, TEM, BET比表面积、 N2等温吸附与脱附、 BJH脱附孔径分布及杂质含量分析等方法对合成产品性能进行了表征. 结果表明 采用浓度为0.1 mol·L-1的(NH4)2CO3·H2O溶液快速倒入浓度为0.1 mol·L-1 的Ce(NO3)3·6H2O溶液中以化学计量比进行反应, 同时加入0.4% (质量分数) PEG4000, 反应时间为10 min, 反应温度为40 ℃, 搅拌速率为800 r·min-1, 经水洗、醇洗、脱水和真空干燥后所得的前驱体于300 ℃的空气中焙烧1 h, 该条件下合成的CeO2属于立方晶系, 空间群为Fm3m, 原生晶粒粒径为5 nm左右, 颗粒粒径为20 nm以下, 比表面积达140.61 m2·g-1, 孔径分布为5～15 nm, 孔径峰值为9.3 nm, 纯度≥99.97%.     

以葡萄糖、丙烯酰胺和硝酸铈铵为原料制备介孔CeO_2

以葡萄糖、丙烯酰胺和硝酸铈铵为原料, 采用水热法制备出大比表面的介孔CeO2. 研究了铈离子价态、原料组成、 水热处理温度和时间以及原料的加入方式等条件对样品性能的影响, 并运用XRD, FT-IR, N2吸脱附和TG-DTG等手段对样品进行了表征. 结果表明, 铈离子价态由三价到四价可使介孔CeO2的比表面有较大的增加. 单独采用葡萄糖(或丙烯酰胺)和硝酸铈铵为原料所制样品的比表面较小, 而当原料组成为葡萄糖、丙烯酰胺和硝酸铈铵时可制得比表面较大的介孔CeO2, 水热处理时间和原料的加入方式对介孔CeO2的性能有一定的影响, 150 ℃水热处理2 d可获得比表面为162 m2 · g-1 的介孔CeO2.     

附载CeO2的纳米γ-Al2O3合成及其悬浮液的分散稳定研究

以异丙醇铝和六水硝酸亚铈为铈源和铝源,采用溶胶-凝胶法制备了前驱体,并将前驱体在800℃下空气中焙烧2 h得到附载CeO2的高纯纳米γ-Al2O3.样品经X射线衍射(XRD)、透射电镜(TEM)、比表面积(BET)、化学成分和杂质含量分析,结果表明:合成的粉末为由γ-Al2O3和CeO2组成的混合物相,两者均属立方晶系,其中γ-Al2O3空间群为O7H-FD3M,CeO2空间群为Fm3m;晶粒平均粒径为15.7 nm,颗粒平均粒径约60～80 nm,粒子呈类球形,比表面积为159.01 m2·g-1;粒子纯度不低于99.97%,CeO2含量为24.22%.红外光谱(IR)测试结果显示,有Al-O-Ce键生成,表明CeO2与Al2O3并非简单混合.进一步通过对其悬浮液体系Zeta电位和吸光度的测定,研究了不同pH值条件、分散剂种类和用量以及氧化剂对其悬浮液分散稳定性的影响;采用超声波分散法,选择硝酸、氢氧化钾溶液作为pH调节剂,异丙醇胺作为分散剂,过氧化氢作为氧化剂,成功制备了长期存放不沉降的附载CeO2的纳米γ-Al2O3CMP浆料,确定了配制的优化工艺条件.     

纳米CeO2的形貌控制与表征

以Ce(NO3)3·6H2O和(NH4)2CO3为沉淀源,利用柠檬酸作为络合剂和分散剂,实现了对CeO2前驱体的形貌和尺寸控制,并采用TEM,TGA和XRD等方法对前驱体及其热分解所得纳米CeO2的形貌及结晶性等进行了表征.结果表明,随着柠檬酸加入量的提高,前驱体形貌从纳米线向类球形颗粒变化,焙烧生成的纳米CeO2颗粒的形貌具有明显继承性,所得CeO2属于立方萤石结构,且随焙烧温度的提高,晶化程度增大.     

爆轰法制备球形纳米CeO2粉末

采用爆轰合成的方法,以Ce(NO3)3·6H2O为原料,制得了CeO2纳米粒子. 炸药采用黑索金粉,添加剂为CO(NH2)2,NaNO2. 爆轰产物经水洗,烘干后,利用X射线衍射仪器和高分辨率透射电镜对实验结果进行了分析. XRD结果表明,该法所得到的CeO2为立方晶系,颗粒平均粒度为33 nm. TEM图像显示其颗粒呈球形,颗粒大小主要分布在20～40 nm之间,颗粒具有较好的分散性. 球形纳米CeO2颗粒的形成原因有两点:(1) 由于爆轰过程的快速性和急剧冷却的特点,CeO2晶粒来不及择优生长; (2) 产物Na2CO3的熔点较低,爆轰时呈熔融状态包覆在CeO2晶核的周围,阻隔了CeO2晶粒的团聚生长.     

铈掺杂TiO2光催化剂的制备及其催化性能

以TiCl4为原料、Ce(NO3)3·6H2O为稀土掺杂剂,制备了不同掺杂量的Ce/TiO2粉体,并进行了DTA-TG,XRD,SEM和TEM表征.实验主要考察铈掺杂对TiO2粉体的表面形状和光催化活性的影响.结果表明,掺铈能明显改善样品的团聚状态,有利于样品比表面积的增大.SEM和TEM对500℃的焙烧样品表征结果,掺杂样品二次颗粒的成孔性远好于没有掺杂的纯样品.掺杂量从m(CeO2)=0.5%增加到m(CeO2)=8%,样品的比表面积增加了74m2·g-1;活性评价结果表明,掺杂铈可有效提高催化剂的光催化活性,其中m(CeO2)=1%的样品活性最好.     

吸附相反应技术用于不同载体表面纳米TiO2的制备

研究了不同载体对吸附相反应技术制备TiO2粒子的影响, 设计了两种不同表面形貌载体的温度实验(A型SiO2: 粒径20 nm, 比表面积640 m2·g-1; B型SiO2: 粒径12 nm, 比表面积200 m2·g-1), 并用电子能谱仪测定了两种载体表面TiO2含量随温度的变化. 结果表明, 两种载体表面Ti含量都随着温度的升高而减少, 且在一定温度范围内存在着突变, 但A载体突变的温度范围是40-60 ℃, 而B载体为30-50 ℃. TEM表征结果则显示, B表面TiO2粒子要比A表面的均匀. XRD得到的晶粒粒径曲线表明, A 载体表面TiO2晶粒粒径随着温度升高而减小并存在着突变, B载体表面粒子粒径则基本不变. 根据硅胶表面的吸附特性, 提出SiO2吸附的共性导致载体表面Ti含量变化曲线存在着共同点, 而载体内外表面的不同形貌则引起其表面吸附层的形貌以及温度敏感性不同, 最终导致两种载体表面Ti含量、晶粒粒径以及形貌上的差别.     

不同铈添加量对CeO2-ZrO2-Al2O3材料性能的影响

采用共沉淀法制备了一系列不同铈添加量的CeO2-ZrO2-Al2O3(CZA)储氧材料,并通过XRD、低温N2吸附-脱附、氧脉冲吸附(OSC)和H2-TPR等手段进行了表征。XRD结果表明,在1 000和1 100℃高温焙烧后,当CeO2添加量为8%时样品具有最好的结构稳定性能。N2吸附-脱附结果表明,CeO2添加量为8%时样品具有最好的织构性能,1 000℃时,比表面积和孔容分别为:136.6 m2.g-1和0.38 mL.g-1;1 100℃时,比表面积和孔容分别为:83.7 m2.g-1和0.23 mL.g-1。OSC结果显示,CeO2添加量为8%时样品具有最大的储氧量,1 000℃和1 100℃分别为70μmol.g-1和31μmol.g-1。H2-TPR结果表明,CeO2添加量为8%时样品具有最佳的还原性能。     

SnO2纳米微晶的合成及气敏性分析

采用溶剂热技术分别在油酸体系及无水乙醇体系中成功地合成了球形和菱形的 Sn O2 纳米微晶。通过X-射线粉末衍射、选区电子衍射、透射电镜和比表面积测定等手段对合成产物的结构进行了表征 ,并对合成产物的气敏性进行了分析。结果表明 :含有精细结构的球形 Sn O2 纳米微晶的比表面积为 1 4 6 m2· g-1,灵敏温度为 1 6 0℃左右 ,适合于作气敏元件材料     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.