超微NaY分子筛的合成(Ⅰ)──添加轻稀土离子的影响

导向剂的陈化时间和反应胶的晶化温度可以影响NaY分子筛的晶化行为.随导向剂陈化时间的增加,NaY分子筛的晶化速度加快,晶粒尺寸减小;随晶化温度的升高,NaY分子筛的晶化速度加快,但晶粒尺寸增加.而向合成体系中添加轻稀土离子(Ln³⁺)对NaY分子筛的晶化行为影响更为明显.与未添加稀土离子时相比较,在一定的稀土离子添加量范围内[n(Ln³⁺)/n(Al³⁺)<0.2],NaY分子筛的晶化速度明显加快而晶粒尺寸显著减小,同时所合成出的NaY分子筛的n(SiO₂)/n(Al₂O₃)比也有较大的提高.添加稀土离子使合成体系中形成异晶晶种的Ln(OH)₃微晶,从而进一步引发NaY分子筛的成核.     

胆固醇(Cholesterol)嵌入卵磷脂(PC)有序体后对其中CaCO3晶型结构的影响

在PC和Chol/PC有序体中进行CaCO₃沉淀反应,用X射线衍射和扫描电镜方法表征了反应物结构,研究了作为有机模板剂的不同分子有序体对CaCO₃的晶型和形态的指导作用.在反胶束合成中出纳米级CaCO₃颗粒.胆固醇对有序体有显著影响,进而影响此体系中形成的CaCO₃晶型,可诱导生成3种CaCO₃异构体:胶体CaCO₃、球霰石和方解石.方解石含量随胆固醇含量增加减少.     

介观结构SiO2/CdO纳米复合物为前驱体原位水热合成半导体CdSe和CdS纳米晶

以高度有序的介观结构SiO₂/CdO纳米复合物为前驱体,在硒源或硫源存在的还原性条件下,利用原位水热反应,合成了介观结构SiO₂/CdSe及SiO₂/CdS纳米复合物,除去SiO₂后,得到半导体CdSe及CdS纳米晶.通过X射线衍射(XRD),高分辨率透射电镜(HRTEM),X射线能散射谱(EDX)及选区电子衍射(SAED)等手段对产物进行了组成和结构表征.结果表明,介观结构SiO₂主体材料在合成过程中起到了一定的形貌和尺寸限制作用,得到的CdSe和CdS均为直径在8 nm左右的类球形六方相纳米晶.     

新型磷酸硅铝分子筛SAPO-56的合成与表征

以N,N,N',N'-四甲基-1,6-己二胺(TMHD)为模板剂,采用水热法在Al₂O₃-P₂O₅-SiO₂体系中合成了SAPO-56分子筛.固定模板剂和水,得到Al-Si-P三元体系相图.当原料物质的量比为0.52)/n(M)<0.7(M=SiO²⁺Al₂O³⁺P₂O₅),0.152O₃)/n(M)<0.4及0.12O₅)/n(M)<0.3时,出现SAPO-56合成的纯相区.固定合成凝胶中硅、铝、磷和水的量,模板剂的用量改变对合成影响较大.n(TMHD)/n(P₂O₅)≥2时,产物是纯SAPO-56.用XRD,SEM,IR,DTA-TG和吸附等方法研究了产物的物化性能.结果表明,SAPO-56分子筛具有较好的热稳定性(骨架坍塌温度为1150℃)和较大的水吸附量(41%).SAPO-56分子筛催化剂对甲醇转化制烯烃反应表现出了良好的催化活性和较高的C₂和C₃烯烃选择性.     

Ni2P/Cu(OH)2催化剂的制备及其全解水性能研究

通过化学处理法在泡沫铜基底表面生成Cu(OH)₂纳米线,大大增加了基底材料的表面积和导电性.采用水热法在Cu(OH)₂纳米线表面制备片状Ni-CH/Cu(OH)₂前驱体,对Ni-CH/Cu(OH)₂前驱体进行低温磷化得到多级结构Ni₂P/Cu(OH)₂催化剂.通过扫描电子显微镜(SEM)、X射线光电子能谱仪(XPS)和X射线衍射仪(XRD)对催化剂的物质结构和表面形貌进行了表征.采用线性伏安法、恒电位等技术对催化剂的电化学性能进行测试.在1.0 mol·L^-1 KOH碱性溶液中,当电流密度为10 mA·cm^-2时,Ni₂P/Cu(OH)₂的析氢反应(HER)和析氧反应(OER)过电位分别为133和333 mV,且均具有较好的稳定性.将这种多级结构Ni₂P/Cu(OH)₂催化剂分别用作阳极和阴极进行全解水电解,电流密度达到10 ...     

一种新型介孔磷酸硅铝(SAPO)分子筛的合成及表征

以Silicate-1晶种为硅源,水热合成了一种新型介孔磷酸硅铝(SAPO-1)分子筛,并且通过X射线粉末衍射、红外光谱、透射电镜、扫描电镜、热重分析、N2吸附/脱附和氨气程序升温脱附(NH₃-TPD)等多种手段对产物进行了表征.红外光谱表明,Silicate-1导向剂成功地引入了介孔骨架;氨气程序升温脱附(NH₃-TPD)结果表明,SAPO-1具有较强的酸性.催化结果表明,SAPO-1在大分子催化反应中有较高的活性.     

纳米晶材料SrMgxTi1-xO3的合成与表征

采用硬脂酸法合成纳米晶SrMg_xTi_1-xO₃(x=0.1～0.5)材料.用DTA,TG,XRD,IR,XPS和TEM进行表征.结果表明,粉末粒径d随SrMg_xTi_1-xO₃中镁含量、烧结温度和烧结时间的改变而变化;烧结所产生的粉末粒度分布均匀、大小适中;Mg²⁺部分替代SrTiO₃的Ti⁴⁺后,O的1_s光谱随着Mg²⁺含量的不同而发生变化.     

不同形貌WO3的水热合成及其在水处理中的应用研究

三氧化钨(WO₃)以其较窄的带隙,成为继二氧化钛(TiO₂)之后颇具发展潜力的n型半导体光催化剂.本文采用水热合成法,通过调控反应参数,如原料组成、沉淀时间等,合成了不同形貌和晶型的WO₃;采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱(FT-IR)、氮气吸附-脱附(N₂ adsorption-desorption)等表征了所合成的WO₃产品,发现原料组成、沉淀时间等条件对WO₃的晶型和形貌都有影响;研究了所合成的WO₃产品去除水中亚甲基蓝染料污染物的性能,结果表明,所制备的WO₃对水中亚甲基蓝具有较好的去除效果,去除率可达97%.     

方形锐钛矿TiO2纳米晶的合成及表征

在不添加任何模板剂或形状控制剂的条件下,以TiCl₄为前体,经氨水沉淀、乙醇洗涤和超临界干燥(AS制备法)选择性地合成了方形锐钛矿TiO₂纳米单晶.热稳定性研究结果表明,当焙烧温度不超过650℃时,方形锐钛矿TiO₂纳米晶的表面积、孔容、晶粒/颗粒尺寸基本保持不变.XRD和拉曼光谱分析表明,方形锐钛矿TiO₂纳米晶在800℃下焙烧后仍能保持晶相不变,表现出很强的抗晶相转变能力.但在1000℃焙烧后,样品可以完全转变成金红石相TiO₂.     

四氢呋喃/水体系中以蒸气相传输法合成高硅FER沸石

以X射线衍射(XRD), 红外光谱(FT-IR), 扫描电镜(SEM), 低温氮吸附, ²⁹Si固体核磁共振(MAS NMR)等研究了含FER晶种的Na₂O-SiO₂-Al₂O₃干胶(SDG)在四氢呋喃(THF)/水(H₂O)混合蒸气相中的结晶行为, 同时研究了体系中THF分子和[SiO₄], [AlO₄]基团在结晶前后状态的变化. 结果表明, 在THF/H₂O混合蒸气中以蒸气相传输法(VPT)可合成结晶度较高、结构完美且孔道开放的FER沸石. ¹³C交叉极化固体核磁共振(CPMASNMR)和差热分析(TG-DTG-DTA)等研究证明THF分子作为模板剂, 位于FER笼内. FER晶种和水能促进FER沸石的结晶.     

聚丁二酸丁二醇酯的自成核结晶行为

利用差示扫描量热仪(DSC)研究了自成核对聚丁二酸丁二醇酯(PBS)的结晶行为的影响. 研究结果表明, PBS的有效自成核温度处理区间为118～120 ℃. PBS经自成核处理后结晶温度提高, 可以在100~118 ℃温度区间内迅速结晶. 同时, 研究了自成核处理后样品在100～104 ℃范围内的等温结晶行为、动力学过程及熔融行为. 结果表明, 随着等温结晶温度的升高, 结晶速率变慢, 熔融曲线出现多重熔融峰. Hoffman-Weeks方程分析结果表明, 自成核处理对PBS的平衡熔点没有影响. Avrami等温结晶动力学方程适合分析自成核处理样品的等温结晶动力学过程, 获得其动力学参数K与n, 其中n值偏大的原因在于自成核的样品结晶生长点增多. 根据Arrhenius方程, 计算获得PBS自成核处理后等温结晶活化能为-286 kJ/mol.     

Crystallization behavior of biodegradable poly(ethylene adipate) modulated by a benign nucleating agent: Zinc phenylphosphonate

Zinc phenylphosphonate (PPZn), a benign and biocompatible nucleating agent, was prepared and incorporated into the biodegradable poly(ethylene adipate) (PEA) to investigate its effect on the crystallization behavior, crystallization kinetics and spherulite morphology of PEA. Upon addition of PPZn, the crystallization temperature and crystallinity of PEA in the non-isothermal crystallization process increased significantly. Analysis of crystallization kinetics by Avrami equation suggests that the crystallization time shortened greatly and crystallization rate increased markedly after addition of PPZn. In the presence of PPZn, the spherulite size decreased and spherulite density increased significantly. It suggests that PPZn is an efficient nucleating agent for the crystallization of PEA. The accelerated crystallization in the presence of PPZn is mainly attributed to the epitaxial nucleation of PEA crystals on the surface of PPZn crystals, that is, a perfect lattice matching between PEA crystal and PPZn crystal occurs.     

The crystallization behavior of biodegradable poly(butylene succinate) in the presence of organically modified clay with a wide range of loadings

The crystallization behavior of poly(butylene succinate)(PBS) nanocomposites with a wide range of contents of clays was revealed. It was of interest to find that the crystallization rate of PBS was accelerated obviously at relatively low contents of clays; while a retarded crystallization kinetics and a decreased crystallinity of PBS were found in the nanocomposites with higher clay contents. Two interplaying effects existed in the nanocomposites, i.e., a suppression effect of clays on nucleation and a templating effect of clays on crystal growth, were clarified to contribute to this intriguing crystallization behavior.     

Enhancing the Crystallization Performance of Poly(L-lactide) by Intramolecular Hybridizing with Tunable Self-assembly-type Oxalamide Segments

In this work, hydroxyl-terminated oxalamide compounds N~1,N~2-bis(2-hydroxyethyl)oxalamide(OXA1) and N~1,N~(1′)-(ethane-1,2-diyl)bis(N2-(2-hydroxyethyl)oxalamide(OXA2) were synthesized to initiate the ring-opening polymerization of L-lactide for preparation of oxalamide-hybridized poly(L-lactide)(PLA_(OXA)), i.e., PLA_(OXA1) and PLA_(OXA2). The crystallization properties of PLA were improved by the self-assembly of the oxalamide segments in PLA_(OXA) which served as the initial heterogeneous nuclei. The crystal growth kinetics was studied by HoffmanLauritzen theory and it revealed that the nucleation energy barrier of PLA_(OXA1) and PLA_(OXA2) was lower than that of PLA. Consequently, PLA_(OXA) could crystallize much faster than PLA, accompanied with a decrease in spherulite size and half-life crystallization time by 74.8% and 86.5%(T=125 ℃), respectively. In addition, the final crystallinity of PLA_(OXA1) and PLA_(OXA2) was 6 and 8 times higher, respectively, in comparison with that of neat PLA under a controlled cooling rate of 10 ℃/min. The results demonstrate that the hybridization of oxalamide segments in PLA backbone will serve as the self-heteronucleation for promoting the crystallization rate. The higher the content of oxalamide segments(PLA_(OXA2) compared with PLA_(OXA1)) is, the stronger the promotion effect will be. Therefore, this study may provide a universal approach by hybridizing macromolecular structure to facilitate the crystallization of semi-crystalline polymer materials.     

晶种法高效合成低硅铝比LSX型分子筛

分别以工业级的偏铝酸钠和水玻璃为铝源和硅源,氢氧化钠为主要碱源,氢氧化钾为辅助碱源,采用LSX晶种法制备了LSX型分子筛。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线荧光(XRF)、傅里叶变换红外光谱(FTIR)和N2吸附-脱附等表征方式考察了有无晶种、钾钠物质的量之比、晶化条件对合成LSX型分子筛的影响。结果表明,加入LSX晶种不仅能显著缩短晶化时间,提高分子筛的结晶度,还可有效抑制方钠石和A型杂晶的伴生;钾钠比过高或过低均会造成A型或方钠石型杂晶的伴生;直接进行高温晶化会导致亚稳态的LSX型分子筛向热力学稳定相转变;延长老化时间或高温晶化处理降低了产物中的硅铝比;样品的比表面积和N2吸附量随老化时间的延长和高温晶化处理而逐渐下降。     

Li-LSX沸石中阳离子分布与空分性能的研究

利用静态交换与动态柱交换的方法对低硅KNaX沸石进行Li~+交换．用XRD， ICP测定样品的晶相及化学红外光谱对LSX在Li~+交换中的骨架振动进行了研究．结 果表明：在Li~+交换过程中，谱峰的位移与本身性质有关，而且与LSX骨架中的离 子位置有关．还探讨了在高交换度的Li-LSX样品上的空分性能布的关系．     

聚ε-己内酯结晶形态的研究

采用DSC测试了聚ε-己内酯(PCL)的结晶温度(TC)和熔融温度(Tm)。同时采用偏光显微镜(POM)探讨了结晶时间的影响,发现结晶时间的改变只能够改变其晶体的尺寸,对其结晶形态并没有太大的影响。最后采用原子力显微镜(AFM)讨论了基底材料、溶剂和过冷度对PCL结晶形态的影响。结果表明:基底材料对PCL结晶形态的影响是比较显著的,PCL在硅片上呈棒状,在云母和涂有碳膜的云母上呈树枝状。溶剂对PCL结晶形态的影响明显,其结晶形态的差别与蒸汽压有关。在不同的温度下PCL结晶形态都成树枝状晶体,且分枝宽度随着过冷度的降低而增加。     

ROLE AND IMPORTANCE OF RADIUS OF GYRATION OF CHAINS IN THE MELT IN THE CRYSTALIZATION OF POLY(1-BUTENE)

Crystallization in polymer systems actually is a process that transfers the entangled melts into a semi-crystallinelayered structure. Whether or not a chain disentangles may result in different crystallization mechanism. When compared tothe crystal thickness (d_c), the volume occupied by the chain in the melt, i.e., the radius of gyration (R_g), plays a veryimportant role in polymer crystallization. When d_c≤R_g, crystallization does not necessitate a chain disentangling. Theentanglements are just shifted into the amorphous regions. However, as d_c>R_g, i.e., as the crystal thickness ges larger thanthe radius of gyration of the chain in the melt, it becomes necessary for a chain to disentangle. Then a change ofcrystallization mechanism occurs. Such change has been experimentally observed in the crystallization of poly(1-butene). Achange in the crystal morphologies from spherulite to quadrangle, is seen via PLM, as crystalliation temperatures increase.Even more, such a change is molecular weigh dependent and shifts to lower temperature as molecular weigh decreases.There exists a jump of crystal thickness and crystallinity associated with morphological change, as seen via SAXS. A changeof crystallization kinetics and crystallinity is further evidenced via dilatometry. The unique feature of P1b crystallization hasbeen discussed based on the radius of gyration of chain in the melt (R_g), and very good agreement is obtained.     

苯乙烯—丙烯酸钠共聚物改性PET结晶行为的研究

本文用DSC和FT-IR方法研究了PET/苯乙烯-丙烯酸钠共聚物共混体系的相溶性、等温结晶动力学、组成、温度等因素对结晶速率、结晶度等结晶行为的影响,并初步探讨了离聚物对PET的作用。     

聚丙烯“催化合金”组成对结晶行为的影响

用示差扫描量热仪(DSC)和偏光显微镜(POM)研究了聚丙烯“催化合金”(PP-cats)组成对等温结晶行为与动力学的影响,并与等规聚丙烯(iPP)进行比较.结果表明,与纯PP相比较,PP-cats的平衡熔融温度明显下降,表明PP-cats中作为主要组分的丙烯均聚物和乙丙无规共聚物之间存在较强的相互作用.PP-cats的结晶初期动力学可用Avrami模型很好地描述,结晶过程均为预先成核和三维生长方式.PP-cats的结晶速率随体系中乙丙共聚物含量的增加而增大,而PP-cats的晶体生长速率随体系中乙丙共聚物含量的增加而减小.由于PP-cats熔体的粘度远高于纯PP,使得PP-cats中PP分子链运动能力降低,导致了PP-cats较低的晶体生长速率.此外,与纯PP相比,PP-cats的成核密度大幅度提高,被认为是PP-cats具有快的结晶速率的主要原因.